Great video. I bought a similar 4in1 from an Austrian company called Zipper, I live in Germany. I have had some trimmers from them in the past and I was pleased. I got a 4in1 trimmer that just worked 25 minutes the first time I fired it and had to send it return it, because the second time I fired it it did not run at all. For days I tried to make it run and did adjustments just like the one you explain, but nothing. Actually, my machine looks exactly likes yours, maybe they all are made in China and sent out in the world, that is why all of them have the same issues and look the same. Great video!
Sounds a little lean. You want to adjust it rich until you hear the rpm's start to drop, then back lean until it peaks again. Turn it about 1/2 turn back rich and that's your starting point. If you just richen it until the rpm's peak like that you're way too lean when it gets under load. You have to keep going until they start to drop again. In general I err on the rich side as it's bad for the spark plug but good for the motor and spark plugs are a few dollars if I foul one.
Thanks for sharing your experience with me it helped me figure out what was wrong with my new 4 in 1 Strimmer with your video I have fixed it so thanks very much .a fantastic from Ireland.☘️
Hi. Just bought one last week used it and was chocking and flooding a lot this will explain why it’s stopped running! I didn’t understand the process of how the fuel mixture screw work’s so I played about with it and I’ve had to order a new Carb as it wouldn’t start anymore.! Took the carb off to notice the gasket broke. Great explanation thank you!
Thanks ran mine for mabey 3 hours than it started acting up took off the cover and seen it was the wrong way after watching this ... feeling alot better about the buy now
That tool is great for you as you know how to proper set up the carb but, for most of the buyers that don´t know how a carb works and what a choke is that particular machine would be totally unusable. Maybe that´s only a special case but it doesn´t mean that you have to be happy with a tool that need service right out of the box. Have one of that machines waiting on the way, but im sure i would tune it even if it works ok because manufacturer don´t. Great video and review.
I have a 52cc earth auger and it looks same engine. I had issues with the screws to the spacer block to the carb backing out. I put some locktite on it and it seemed to solve the issue. Before I figured out what was going on it was hard to start and run and got increasingly worse.
Mine would bog down and stop after 20 minutes when I bought it. Found it was building a lot of vacuum in the petrol tank because the vent in the petrol cap could not work efficiently enough as the tank is quite large. Replaced cap, - same problem. Fixed by adding a 3 hole grommet where the fuel lines go into tank and fitted a vent line with breather valve. I have 3 Chinese trimmers, all reliable and parts are easy to get. Only weakness is the pull starter so pays to have a spare tucked away so you're not left stranded if it breaks
Thats real handy to know as I couldn't work out why mine today kept stalling when I turned the choke "off" (ON) now I know I'll be able to re-adjust it back (after me messing with it)...lol....cheers, really helpful.
Remember as the filter in the tank gets clogged over time people usuely adjust the carb to compensate for fuel starvation always check tank filter aswell
I think the design makes more sense on that 2-stroke engine than the troy-bilt because of the way the gas-tank is made the gas tank is always up when you put the engine down; while the troy-bilt you have to turn it on the side to pour gas in.
ha this was awwsome i just orderd one this morening before waching this so thanks for the heads up looks like it will be a good product for the house when needed
I was asked if I could have a look at this very same machine for an in-law. I had the choke on when I thought it was off could I get it to run right, nay lad. I removed the intake cover to inspect the filter and figured it out that I was upside down. However when I looked again closely at the printing on the plastic it must have been realised by the manufacturer to be wrong (this must be a younger model than yours ) so on this model they replaced the on /off with two tiny little pictures of a butterfly valve vertically open the other horizontally closed in the correct positions but man not easy to see especially for an auld codger like me. The large word CHOKE at the bottom of the slide space in the plastic is really misleading. I mean usually you move the lever towards the word choke not away from it. I got this thing working the block between the engine and carburettor had come loose and the gasket if there was one was gone so I made one with thin gasket sheet. Thread lock is recommended for the bolts. Great video.
I have one similar to this I have a BC520 52cc 5 in 1 and a timber pro 62cc 6150 had it 3 years and fellow Pennsylvania resident I like your videos I saw the slippery rock hoodie .
You say maybe you'll put a label on the choke, but there is already one. the little square label between the choke lever and the motor shows the correct choke position.
It's unbelievable how cheap this thing is. You said it, for the price of one attachment from one of the name brands you can buy 5 attachments AND the power head. crazy. How is the power compared to a regular 25-28cc string trimmer?
I had exactly the same problem yesterday with my pole pruner.It got me mad and fuming until I removed the air filter to see the choke was ON when it says OFF.
When it rides good it really good, but it's trouble starting and bogs down to shut off after reaching top speed and right before it does, kicks in again. Gets gas then don't, then does and dont.
Ummm you need to pump the light bulb more until it shows mixture of gas and oil through those 2 clear tube. What level do you have the speed, the flat screw head. I would put it on 2.5.
I ah E one like this but it’s blue and SGS branded. First t would not prime but cleaned carb/bulb/diaphragm and it does. The it would start and drop off on applying revs. Now the pull Chord has snapped!! I’m looking at ways to replace it not replace the whole unit.
Same motor as my stand up scooter, it's called a Burner DX but I've yet to find any online that even look similar, your engine is dead on tho. I'm getting ready to ride full speed into a hickory tree...
Yeah man I had the same problem with the choke on my gas powered stand up scooter I bought has this exact same engine as one in video I thought I blew it up but nope choke was upside down
I have a motorsense timberteck ms52-2tl and the engine keeps stopping and kicks back it has had a long history of kick back and the compression was too high and I was un able to pull the cord properly because of kickback. I took of the cylinder off to de coke it and made a plate 4mm thick to soften the compression now the carbourettor needs replacing as it is flooding the engine I think a walbro carb will fit it. I think the strimmer I have is an early version of the one from ebay. Given the problems ive had so far I do not know if it is worth repairing. Given the small space in the combustion chamber it would need to be de- carbonised regularly most likely after 2 seasons. However sinse I reduced the compression its a lot easier to pull the cord and its possible to get to the end of the cord. The pullcord casing is broken because of the kickback problem which is refusing to be solved. I even elonggated the holes in the ignition coil stattor to retard the timming but to no avail.
Coocheer brush 42&58cc cutter carburator cannot be high speed adjusted. For that matter it can't be low speed adjusted either. Only idle speed is adjustable.😱😡
i can't believe it even ran at all if you thought choke was setup correctly...do you have update on it? what the mix ratio? 50 to 1??? also how well does chainsaw and hedge trimmer work ?? will hedge trimmer cut 3/4'' branches? thanks
Green x . Gtx 520 but is the same as eco but here is 175$ only.. and u plough axe... Mine it start but when u exalte it loose power and off and from there u can't start. .. what is the problem..
I have cheap trimmer. Advice: don't buy cheap shit. So much time on fixing that weak garbage 🗑️. Buy normal trimmer which will work and last a lifetime. Mine gave me a headache from the day 1.
Bugger eh! that would be enough to throw for a loop for sure. Good thing you got it figured out. I bought a cheap yardworks string trimmer the other day it wouldin't even run until I adjusted the carb. She runs like a dream now though.
It definitely sounds a lot better. If I was only listening to this video, I'd be swearing you were running the TimberPro. The choke sticker was put on backwards.
@@Lanninglongarmmowing IT looks pretty high quality. You can't go into a dealership and find a 50 CC weed eater and if you order one its over a thousand
You are correct. Mine starts on the third pull. They put grease zerts on the hedge trimmer and the pole saw attachments. I was really surprised at that. You can't beat this machine for the price and what you get. Just know it's not very light however, they give you a harness for it also which makes it a lot easier to hold for long periods of time.
@@Lanninglongarmmowing I'm assuming mine is the same brand as yours. I deduct so because clearly 10 different sellers on Amazon were selling part or all of this setup
What one me over to the "it can be cheap and it can be good" likelihood was buying the Chinese clone 92 CC saw www.huztl.net/Outdoor-Power-Equipments-c6922.html IF the quality is high, I just replaced 1700 worth of equipment for 220
Great video. I bought a similar 4in1 from an Austrian company called Zipper, I live in Germany. I have had some trimmers from them in the past and I was pleased. I got a 4in1 trimmer that just worked 25 minutes the first time I fired it and had to send it return it, because the second time I fired it it did not run at all. For days I tried to make it run and did adjustments just like the one you explain, but nothing. Actually, my machine looks exactly likes yours, maybe they all are made in China and sent out in the world, that is why all of them have the same issues and look the same. Great video!
Sounds a little lean. You want to adjust it rich until you hear the rpm's start to drop, then back lean until it peaks again. Turn it about 1/2 turn back rich and that's your starting point. If you just richen it until the rpm's peak like that you're way too lean when it gets under load. You have to keep going until they start to drop again. In general I err on the rich side as it's bad for the spark plug but good for the motor and spark plugs are a few dollars if I foul one.
Running it to rich is bad for the motor and piston rings but rebuild kits are cheap
Thanks for sharing your experience with me it helped me figure out what was wrong with my new 4 in 1 Strimmer with your video I have fixed it so thanks very much .a fantastic from Ireland.☘️
Hi. Just bought one last week used it and was chocking and flooding a lot this will explain why it’s stopped running! I didn’t understand the process of how the fuel mixture screw work’s so I played about with it and I’ve had to order a new Carb as it wouldn’t start anymore.! Took the carb off to notice the gasket broke. Great explanation thank you!
I have the same machine, different manufacture which I am having simular situation, many thanks for putting this up, cheers.
Thanks ran mine for mabey 3 hours than it started acting up took off the cover and seen it was the wrong way after watching this ... feeling alot better about the buy now
I cant believe it pal i am having the same issue with mine and it was driving me crazy. Thank you for sharing this video my friend.
That tool is great for you as you know how to proper set up the carb but, for most of the buyers that don´t know how a carb works and what a choke is that particular machine would be totally unusable. Maybe that´s only a special case but it doesn´t mean that you have to be happy with a tool that need service right out of the box.
Have one of that machines waiting on the way, but im sure i would tune it even if it works ok because manufacturer don´t. Great video and review.
I have a 52cc earth auger and it looks same engine. I had issues with the screws to the spacer block to the carb backing out. I put some locktite on it and it seemed to solve the issue. Before I figured out what was going on it was hard to start and run and got increasingly worse.
Mine would bog down and stop after 20 minutes when I bought it. Found it was building a lot of vacuum in the petrol tank because the vent in the petrol cap could not work efficiently enough as the tank is quite large. Replaced cap, - same problem. Fixed by adding a 3 hole grommet where the fuel lines go into tank and fitted a vent line with breather valve. I have 3 Chinese trimmers, all reliable and parts are easy to get. Only weakness is the pull starter so pays to have a spare tucked away so you're not left stranded if it breaks
Same here. I’ve 2 Chinese strimmers and they’re fucking beast the only thing is that I can’t seem to tune it properly on the new one
Thats real handy to know as I couldn't work out why mine today kept stalling when I turned the choke "off" (ON) now I know I'll be able to re-adjust it back (after me messing with it)...lol....cheers, really helpful.
Remember as the filter in the tank gets clogged over time people usuely adjust the carb to compensate for fuel starvation always check tank filter aswell
I think the design makes more sense on that 2-stroke engine than the troy-bilt because of the way the gas-tank is made the gas tank is always up when you put the engine down; while the troy-bilt you have to turn it on the side to pour gas in.
ha this was awwsome i just orderd one this morening before waching this so thanks for the heads up looks like it will be a good product for the house when needed
I was asked if I could have a look at this very same machine for an in-law. I had the choke on when I thought it was off could I get it to run right, nay lad.
I removed the intake cover to inspect the filter and figured it out that I was upside down. However when I looked again closely at the printing on the plastic it must have been realised by the manufacturer to be wrong (this must be a younger model than yours ) so on this model they replaced the on /off with two tiny little pictures of a butterfly valve vertically open the other horizontally closed in the correct positions but man not easy to see especially for an auld codger like me. The large word CHOKE at the bottom of the slide space in the plastic is really misleading. I mean usually you move the lever towards the word choke not away from it.
I got this thing working the block between the engine and carburettor had come loose and the gasket if there was one was gone so I made one with thin gasket sheet. Thread lock is recommended for the bolts.
Great video.
damn right thread lock is recommended, it's a must or you'll blow your muffler into the neighbors yard for sure!
Perfectly tuned, well done mate :)
I have one similar to this I have a BC520 52cc 5 in 1 and a timber pro 62cc 6150 had it 3 years and fellow Pennsylvania resident I like your videos I saw the slippery rock hoodie .
What type of fuel are you using for
@@tongombota8853 I use 25 to 1 that what my owners manual says i 87 octane I used VP racing 2 stroke oil from tractor supply
Up=start=air closed
Down=run= air opened
Here in the UK , it comes under the Parker brand name and properly labeled . Down for choke off .
You say maybe you'll put a label on the choke, but there is already one. the little square label between the choke lever and the motor shows the correct choke position.
Yes I see what you mean, its as if they have made the cover about face an realised it and added the sticker on the left, which is the correct way.
These are the same as the Komatsu G4K, they are all replicas of a very good machine!
This video helped me out alot. You gave me a good starting point. Let you know thanks
It's unbelievable how cheap this thing is. You said it, for the price of one attachment from one of the name brands you can buy 5 attachments AND the power head. crazy. How is the power compared to a regular 25-28cc string trimmer?
I had exactly the same problem yesterday with my pole pruner.It got me mad and fuming until I removed the air filter to see the choke was ON when it says OFF.
At 5:21 I see a big square white label with a diagram saying "Cold start" at the top, lever in raised position.
The choke is in run position / OFF / engine warm always way down.
Yes absolutely, too lean . It's funny about this motor because it looks similar to my stand-up scooter, a 2 stroke, 49cc. But it rides great.
I too have a stand up scooter with this motor and I've had it a month and still trying to get it right
When it rides good it really good, but it's trouble starting and bogs down to shut off after reaching top speed and right before it does, kicks in again. Gets gas then don't, then does and dont.
Ummm you need to pump the light bulb more until it shows mixture of gas and oil through those 2 clear tube. What level do you have the speed, the flat screw head. I would put it on 2.5.
I'll check in the morn and get back with you
Yes ok
So that is the single screw one, some have two adjustment screws H and L adjustments.
Mine is exactly the same but has no adjustment screw. There's something there but it's smooth headed and doesn't adjust
I ah E one like this but it’s blue and SGS branded.
First t would not prime but cleaned carb/bulb/diaphragm and it does.
The it would start and drop off on applying revs.
Now the pull
Chord has snapped!!
I’m looking at ways to replace it not replace the whole unit.
My advice is if yr not a mechanic dont mess with it...
Same motor as my stand up scooter, it's called a Burner DX but I've yet to find any online that even look similar, your engine is dead on tho. I'm getting ready to ride full speed into a hickory tree...
Yeah man I had the same problem with the choke on my gas powered stand up scooter I bought has this exact same engine as one in video I thought I blew it up but nope choke was upside down
Can u do a video on where the carb filter is
Can you please tell me what the black screw is for on the trigger handle.
Also when it is now being used it really vibrates, any suggestions
In terms of vibration there is no solution for it unless you grease it
I’m trying to replace a carburetor on one of these. Can’t seem to find anyone with pictures of the full carburetor to tell which one to order.
I have a motorsense timberteck ms52-2tl and the engine keeps stopping and kicks back it has had a long history of kick back and the compression was too high and I was un able to pull the cord properly because of kickback.
I took of the cylinder off to de coke it and made a plate 4mm thick to soften the compression now the carbourettor needs replacing as it is flooding the engine I think a walbro carb will fit it.
I think the strimmer I have is an early version of the one from ebay.
Given the problems ive had so far I do not know if it is worth repairing.
Given the small space in the combustion chamber it would need to be de- carbonised regularly most likely after 2 seasons.
However sinse I reduced the compression its a lot easier to pull the cord and its possible to get to the end of the cord. The pullcord casing is broken because of the kickback problem which is refusing to be solved. I even elonggated the holes in the ignition coil stattor to retard the timming but to no avail.
My weed trimmer is also giving problems it starts but won’t operate what could be the issue?
On the top of mine is a tiny brass screw, any idea what that is for. Thanks
Coocheer brush 42&58cc cutter carburator cannot be high speed adjusted. For that matter it can't be low speed adjusted either. Only idle speed is adjustable.😱😡
i can't believe it even ran at all if you thought choke was setup correctly...do you have update on it? what the mix ratio? 50 to 1??? also how well does chainsaw and hedge trimmer work ?? will hedge trimmer cut 3/4'' branches? thanks
I just mix it without even measuring it
Hi there can i ask you why the hedge trimming tool moves whilst in idle mode interesting about the choke
excellent video.....thanks
If you look closely at the white label it is mentioned correctly.
Do you know if the trimmer head and saw come pre packed with grease have not ran um yet
Mine is doing the Samething where do I find the adjust
Green x . Gtx 520 but is the same as eco but here is 175$ only.. and u plough axe... Mine it start but when u exalte it loose power and off and from there u can't start. .. what is the problem..
Same issue. Did you ever find the solution? Please share.
i have just got one off these when i pull the string it just judders any idear what am doing wrong pls help
Flip the choke the other direction.
Do you know there's another mix adjust screw.
$175.00 is not cheap!
Well considering everything it comes with and the size of the engine it's pretty cheap.
Yo bro, i just bought one but won't start despite using the right fuel-oil ratio. Any suggestions bro?
The choke is marked incorrect on these machines. That is probably your reason it won't start. Check the spark plug also.
I had the same problem.
My choke is the same.
I have cheap trimmer. Advice: don't buy cheap shit. So much time on fixing that weak garbage 🗑️. Buy normal trimmer which will work and last a lifetime. Mine gave me a headache from the day 1.
How much did you pay for it and what is the brand name? It looks like a copy of a shindaiwa.
Got it 175.00
What is the oil mixture ratio? 2 per cent?
25 to 1
@@roblord7610 That's a lot of oil !!
@@mathieutallard6328 Agreed, but that's what they all spec in the manuals
Did it last long?
Yes still running good today.
300 bucks now.
sound is to low
This engine is a mitsubishi TL32 brand knock off....
It's still to lean
हींदी मे बताए
Bugger eh! that would be enough to throw for a loop for sure. Good thing you got it figured out. I bought a cheap yardworks string trimmer the other day it wouldin't even run until I adjusted the carb. She runs like a dream now though.
Great video! People helping people I'm getting one soon.
Always adjust the carborator under load get the correct high side
Entertaining and helpful thank you
But other than that, ive used all the attachments and this thing KICKS ASS!
It definitely sounds a lot better. If I was only listening to this video, I'd be swearing you were running the TimberPro. The choke sticker was put on backwards.
That's molded into the plastic. No sticker
Then is a horrible job ny the mold designer.
@@MrBooMY3 The sticker says the same thing as the mold.
Is that a shindaiwa trimmer I have one I don’t use but it runs good kinda looks like it
Ive got about 4 hrs of use on mine. And it seems that it works itself out of adjustment after about 30-45 mins of use. Have you had this same issue?
same problem.....this video explains it all
I ordered one of these and get it Monday
Glad to hear it. You won't believe how much power it has.
@@Lanninglongarmmowing IT looks pretty high quality. You can't go into a dealership and find a 50 CC weed eater and if you order one its over a thousand
You are correct. Mine starts on the third pull. They put grease zerts on the hedge trimmer and the pole saw attachments. I was really surprised at that. You can't beat this machine for the price and what you get. Just know it's not very light however, they give you a harness for it also which makes it a lot easier to hold for long periods of time.
@@Lanninglongarmmowing I'm assuming mine is the same brand as yours. I deduct so because clearly 10 different sellers on Amazon were selling part or all of this setup
What one me over to the "it can be cheap and it can be good" likelihood was buying the Chinese clone 92 CC saw
www.huztl.net/Outdoor-Power-Equipments-c6922.html
IF the quality is high, I just replaced 1700 worth of equipment for 220