Good job. When you said it would start and then stop, my first thought was an optical encoded disk on the treadmill drive wheel was loose. Sometimes those are held on with basically double-side tape on the disk and over time it fall down to the shaft. Symptoms are the same. The belt starts to move and then stops then the speed controller doesn't get feedback. I guess we need to stock various power mosfets anymore. I'm starting to run across more and more of them.
One thing I would like to know is when you applied speed using the console when it was broke did the LED flash ? I am reading that a flashing LED indicates the console control signal is getting to the motor control board even if the motor control board is not working right. So a flashing LED would indicate a working console. It would seem they would have this to isolate the console out of the possible faults. Just don"t know. Anybody ? Thanks. Nice repair job. Tooth pick, nice tip.
I’m having the same problem! The belt motor briefly turns on then cuts out! the power light on the controller board is lit but turns off at the same time I hit the start button and the motor briefly starts and shuts off! Then the power light comes back and resets to do the same thing over & over! Also the ceramic part 7W 3K3J FY gets really hot is this normal? Pls advise!
Great Video. Need input....Still more issues on my end. Moffett burned twice now. Cleaned belt rollers. Bearings smooth belt ok and greased with proform silicone. Tested pulse sensor is working. Unit runs great after changed twice mosfett by itself no issues. If one gets on control light blinks alternate red motor stops. If done several times burns mosfett shorts it out(both times). I think power is not regulated well upon runner on treadmill. Will not compensate well. Tested dc motor 18v battery. Works fine. As I mentioned runs great without me running on treadmill at level 1 through 10 from console. If I get on treadmill it bogs down and shuts off or overheats and burns the mosfetts twice now. As seeing videos maybe a broken winding in motor shaft. From tear wear giving no torque on ones weight on treadmill run and forces a burn?. Did you experience on your norditrack similar after your repair? Any other situation? Thanks.
@@TarmiziHamid found my problem. The controller fixed, motor hold torque and belt. What was the issue was the running board(wooden deck) of the running belt. It was worn and scratch of the black smooth surface. So, I flipped the board around. Redo the holes snd is working. Yet not as new since the belt is to expensive to replace and has some life left in it. Unit is old and is best to get a newer one. Tear and wear product.
Hi, Thank you for sharing your video, i've got the same problem as you. I replace the defective MOSFET by new one. The belt run approx 500m and the MOSFET burn again. Do you have any ideas what is the cause ? MOSFET is a IRFP250N from China
I have the same board, but my problem is once I start walking on it after a few seconds the treadmill just stops. If I take my feet off the belt it starts up again. You think this could be the issue?
I've replaced the mosfet twice now. After replacing works great. Upon running board light showing alternate red light no longer constant motor stops. If done constantly burns Moffett. Must be something in the board power dc not regulating pulse and lacks self power adjustment till burn out. Tested speed pulse sensor and works fine. Did you find a repair?
Good
Good job. When you said it would start and then stop, my first thought was an optical encoded disk on the treadmill drive wheel was loose. Sometimes those are held on with basically double-side tape on the disk and over time it fall down to the shaft. Symptoms are the same. The belt starts to move and then stops then the speed controller doesn't get feedback. I guess we need to stock various power mosfets anymore. I'm starting to run across more and more of them.
Hello I need this parts,where find.
WTF are you talking about. These things have one board. It’s not an SR 72
This is a bandaid fix. You don't explain what caused it to blow in the first place.
One thing I would like to know is when you applied speed using the console when it was broke did the LED flash ? I am reading that a flashing LED indicates the console control signal is getting to the motor control board even if the motor control board is not working right. So a flashing LED would indicate a working console. It would seem they would have this to isolate the console out of the possible faults. Just don"t know. Anybody ? Thanks. Nice repair job. Tooth pick, nice tip.
I’m having the same problem! The belt motor briefly turns on then cuts out! the power light on the controller board is lit but turns off at the same time I hit the start button and the motor briefly starts and shuts off! Then the power light comes back and resets to do the same thing over & over! Also the ceramic part 7W 3K3J FY gets really hot is this normal? Pls advise!
Great Video. Need input....Still more issues on my end. Moffett burned twice now. Cleaned belt rollers. Bearings smooth belt ok and greased with proform silicone. Tested pulse sensor is working. Unit runs great after changed twice mosfett by itself no issues. If one gets on control light blinks alternate red motor stops. If done several times burns mosfett shorts it out(both times). I think power is not regulated well upon runner on treadmill. Will not compensate well. Tested dc motor 18v battery. Works fine. As I mentioned runs great without me running on treadmill at level 1 through 10 from console. If I get on treadmill it bogs down and shuts off or overheats and burns the mosfetts twice now. As seeing videos maybe a broken winding in motor shaft. From tear wear giving no torque on ones weight on treadmill run and forces a burn?. Did you experience on your norditrack similar after your repair? Any other situation?
Thanks.
if it happening more than once its the motor issue. the motor will runs on 18vdc but when running on 180vdc the current too high burned the IGBT.
@@TarmiziHamid found my problem. The controller fixed, motor hold torque and belt. What was the issue was the running board(wooden deck) of the running belt. It was worn and scratch of the black smooth surface. So, I flipped the board around. Redo the holes snd is working. Yet not as new since the belt is to expensive to replace and has some life left in it. Unit is old and is best to get a newer one. Tear and wear product.
I have error 04 and I changed the mosfet but nothing happened the same error
Which numbers should I pay attention to when ordering a transistor for my treadmill
Can you tell me the name of the part I have the same treadmill doing the same thing
Hi does any one could tell me what to do my tread mill belt won't move, I have a Diamondtrack tread mill.
Hi, Thank you for sharing your video, i've got the same problem as you. I replace the defective MOSFET by new one. The belt run approx 500m and the MOSFET burn again. Do you have any ideas what is the cause ? MOSFET is a IRFP250N from China
Could be bad motor blew the MOSFET to begin with.
thanks found the same shorted mosfet ordered a pack of 5 hope there real lotta fakes out there
I have the same board, but my problem is once I start walking on it after a few seconds the treadmill just stops. If I take my feet off the belt it starts up again. You think this could be the issue?
Same here
Might be the speed sensor.
I've replaced the mosfet twice now. After replacing works great. Upon running board light showing alternate red light no longer constant motor stops. If done constantly burns Moffett. Must be something in the board power dc not regulating pulse and lacks self power adjustment till burn out. Tested speed pulse sensor and works fine. Did you find a repair?