Can u share the details of the setup? Can u also please share the setup of the helicopter itself like model make and everything i wanna build or buy this system.
It is recommended to start reading from the official wiki page of Ardupilot, which has a very detailed introduction of each link:ardupilot.org/copter/docs/traditional-helicopters.html
I think the pixhack 5 has more damping than the pixhawk and even the pixhack 3 use more damping! That is why people use them to manage vibration( low frequency is always problem) also the belt drive is less vibration than TT
That's right, the Pixhack V5 and Pixhack V3 series have built-in IMU dampers that do filter a portion of the vibration. The belt drive vibration may be smaller than the shaft drive, but it is not absolute. The shaft drive assembly and debugging are in place, and good vibration control can be obtained.
The V5 and V5+ have built-in damping damping, which has a better elimination effect on the mechanical vibration of the helicopter, but the volume and quality will be bigger and heavier. If it is a larger proportion of RC helicopters, it is definitely more suitable for V5 / V5+.
Sorry, this 420-class RC helicopter, I have now replaced the Pixhack V5 nano flight controller without built-in damping, still have good flight performance, because the V5 nano is smaller, here is its flight video:ua-cam.com/video/xv0QlTODa7s/v-deo.html
@@zhangpengsir I am thinking to go with v5+ this time for my 900 size homebuild heli I just installed pixhawk 1 for my Trex 450 but I noticed when I do prefligt check the axis not moving only very little When I move the heli left or right or yaw any direction the correction of the FC is very little And the heli will not lift the ground! And shutting off the motor 😠
The parameters of the total distance and the periodic variable distance to be set are adapted to the mechanical action, and the appropriate flight mode, such as the primary test flight, is used, and the "stablels" mode is used.
@@zhangpengsir oh so you mean there is no parameters to increase or decrease the FC movments? My other 600 size has better response and more movement when I shake the heli ! The swash and the tail move more ! This one j very little movement ! Thank you for your reply !
Use wifi radio to connect to the flight control on the plane, and edit the automatic task on the mobile phone ground station to send the flight control to the helicopter. I think if you have operated ardupilot, you should know it when you see it!
Very good and awesome research!
Thank you for your attention
hey. Is there any way to configure a Pixhawk 6c on the helicopter 450?
I saw CUAV pixhack V5 ardupilot , it is so cool , thanks so much dear !!
Can u share the details of the setup? Can u also please share the setup of the helicopter itself like model make and everything i wanna build or buy this system.
It is recommended to start reading from the official wiki page of Ardupilot, which has a very detailed introduction of each link:ardupilot.org/copter/docs/traditional-helicopters.html
I think the pixhack 5 has more damping than the pixhawk and even the pixhack 3 use more damping! That is why people use them to manage vibration( low frequency is always problem) also the belt drive is less vibration than TT
That's right, the Pixhack V5 and Pixhack V3 series have built-in IMU dampers that do filter a portion of the vibration. The belt drive vibration may be smaller than the shaft drive, but it is not absolute. The shaft drive assembly and debugging are in place, and good vibration control can be obtained.
dose PIXHAWK V5 is better than this one? I mean newer! did you notice any different in the dampening or vib between the V5 and this one?
thank you
The V5 and V5+ have built-in damping damping, which has a better elimination effect on the mechanical vibration of the helicopter, but the volume and quality will be bigger and heavier. If it is a larger proportion of RC helicopters, it is definitely more suitable for V5 / V5+.
Sorry, this 420-class RC helicopter, I have now replaced the Pixhack V5 nano flight controller without built-in damping, still have good flight performance, because the V5 nano is smaller, here is its flight video:ua-cam.com/video/xv0QlTODa7s/v-deo.html
@@zhangpengsir I am thinking to go with v5+ this time for my 900 size homebuild heli
I just installed pixhawk 1 for my Trex 450 but I noticed when I do prefligt check the axis not moving only
very little
When I move the heli left or right or yaw any direction the correction of the FC is very little
And the heli will not lift the ground!
And shutting off the motor 😠
The parameters of the total distance and the periodic variable distance to be set are adapted to the mechanical action, and the appropriate flight mode, such as the primary test flight, is used, and the "stablels" mode is used.
@@zhangpengsir oh so you mean there is no parameters to increase or decrease the FC movments?
My other 600 size has better response and more movement when I shake the heli ! The swash and the tail move more !
This one j very little movement !
Thank you for your reply !
What setup are you using on transmitter, normal Plane, or helicopter .. that is what i can´t find information anywhere...
Use wifi radio to connect to the flight control on the plane, and edit the automatic task on the mobile phone ground station to send the flight control to the helicopter. I think if you have operated ardupilot, you should know it when you see it!
What size blades you use ? 360 or 380, thanks bro
420mm blades
张朋大哥 这个地面站和飞控之间的数传是什么解决方案? 我也想在遥控器上放个平板当地面站
wifi数传,可以近距离通讯
How does this differ from other flight controllers used for fpv quadcopters?
No difference, just when used on a traditional helicopter, debugging is much more difficult.
what is rotor speed ? looks so stable
about 2000rpm
Bro ..What the pixhawk PX4 2.4.8 can also be used on helicopters
it is pixhack V5 , HAHA
Hello,
Are you using an external FLB system?
Rotem Shfaim Did not use the fbl unit, just use the independent pixhack v5 flight control!
美丽 :D
thanks
_好厲害,我也想學!
从wiki开始,www.ardupilot.org
Is this easy to set up on a 600 size?
yes
请问在哪里可以买到这个Pixhawk系统?
www.taobao.com,CUAV雷迅创新
nice
张sir 我也想学习飞控,能收我为徒吗?
交学费可以
@@zhangpengsir 没有问题 可以给一个联系方式吗?
@@yetrex539 qq:19654241,注明youtube