One side of the loop broke on me. I grabbed some JB weld and re-enforced both sides. She is solid as a rock now. My issue is she eats batteries unless I remove them after every trip. I called MG about this and they did acknowledge that this was an issue with earlier models. Because it is out of warranty I am sol. I may install a micro switch to electrically break the circuit when not in use.
Glad to see your up and running as far as UA-cam goes! Good video! I had the same problem with my food scale in the kitchen, and I found some narrow insulation out in the garage that was for a pickup bed cover. I cut a small piece of that off, and stuck it to the cover to put pressure against the battery's and haven't had any trouble since..
Thanks for the video! I have not had a problem, yet, with the attachment spot. I do, however, hate that remote. Mine draws down the batteries when they are sitting in the remote when not in use. So, I actually use rubber bands to hold the thing together because every time I'm done fishing I have to take the batteries out and store it all in a sealed bag otherwise the batteries are dead within 2 weeks. Each time I arrive at the ramp, I reassemble using the rubber bands to hold the dang thing together. When that lanyard holder breaks, I'm SOL! Might be time to buy a new remote and get that lanyard mount!
Are you sure? Because the factory batteries were fully working when I powered it on for the first time today and I got the motor back in november. The motor was also sitting in the cold garage.
@@kenz1031 I suspect that mine is defective. I’ve tested many times in various ways. As long as I keep the batteries out, it’s fine when I need it for the day. If I leave them in, they die before the next trip. I should likely buy a new remote!
Wouldn't matter if it did fall in the water, it floats, thankfully. I was leaning over, deploying the motor today and it ripped the remote off my neck and into the water, I just floated over and grabbed it and it was fine.
Hello from New Mexico. Do you like the fob for control? At times I wish both hands were free. Just ordered the wireless foot pedal. Have you tried it? Good job on the video, BTW.
The fob isn't perfect for sure. There are plenty of times I have to use it when I really need to be working the rod. Would love to hear your feedback on the wireless foot control and your set up. Thanks for the kind words too!
Also, the remote isnt waterproof, and wont float. Fill the inside completely with cheap silicone caulk. Holds the batteries in place and keeps water out. Silicone is easy to pull out when its time to change batteries.
I would not go so far as to call it 'a piece of crap", but I understand the frustration! I would have contacted MG directly to drastically improve your chances of actually getting MG to improve the product vs just belly ache over it behind the scenes. Each to his own, but I think it is crappy idea to chose the hand remote over the wireless foot pedal in the first place! The foot pedal is extremely light, effort less to steer (no cables like the useless clunker hard to steer cable driven models! MOST important IT FREES UP Both HANDS for the task at hand..Catching Fish! FISH ON!
Not many kayakers are running the foot pedal due to stability. But if you are able to do it, good on you. By the way, motorguide did improve it by making the piece that breaks a bit thicker but it's still going to break. Thanks for your input
@@Fishin1AZlol I don't know where you're from, but LOTS of guys who run the xi3 in the Hobie BOS use the pedal. If you are comfortable standing and fishing, using the pedal is a no brainer.
I don’t want a kill switch in my kayak. If I fall out and can’t get to my kayak, I’m screwed. I’d rather be able to drive the kayak back to me. This isn’t a powerboat.
@@XploreAz Sure are putting a lot of faith in that controller? When the yak is upside down you're "controlling" nothing and yet the motor is still running! When you right the yak while the motor is running (assuming you don't get chopped up) how do you intend to get back in as the yak launches the second the prop hits the water?
One side of the loop broke on me. I grabbed some JB weld and re-enforced both sides. She is solid as a rock now. My issue is she eats batteries unless I remove them after every trip. I called MG about this and they did acknowledge that this was an issue with earlier models. Because it is out of warranty I am sol. I may install a micro switch to electrically break the circuit when not in use.
That's great info thanks for sharing!
Glad to see your up and running as far as UA-cam goes! Good video! I had the same problem with my food scale in the kitchen, and I found some narrow insulation out in the garage that was for a pickup bed cover. I cut a small piece of that off, and stuck it to the cover to put pressure against the battery's and haven't had any trouble since..
Good idea!
neat video, motorguide could simply reinforce the area with a metal dowel in that area, that would keep from breaking it in the first place.
Yep, that's a great idea, actually.
I love your honesty, and use of the word fixin😂🙌🙏 great fix!
HAHAHA That's from when I lived in Texas as a kid! Too funny.
Thanks for the video! I have not had a problem, yet, with the attachment spot. I do, however, hate that remote. Mine draws down the batteries when they are sitting in the remote when not in use. So, I actually use rubber bands to hold the thing together because every time I'm done fishing I have to take the batteries out and store it all in a sealed bag otherwise the batteries are dead within 2 weeks. Each time I arrive at the ramp, I reassemble using the rubber bands to hold the dang thing together. When that lanyard holder breaks, I'm SOL! Might be time to buy a new remote and get that lanyard mount!
Good tip, thanks! I just bought a spare remote and am going to look and see if I can do something with the batteries. Thanks for posting!
Are you sure? Because the factory batteries were fully working when I powered it on for the first time today and I got the motor back in november. The motor was also sitting in the cold garage.
@@kenz1031 I suspect that mine is defective. I’ve tested many times in various ways. As long as I keep the batteries out, it’s fine when I need it for the day. If I leave them in, they die before the next trip. I should likely buy a new remote!
Thanks for the info sharing bro. I just ordered mines using the link you provided.
That's cool man, both work great
You are going to love it! I just ordered a spare remote and will add one to it as well. Thanks for the comment!
Wouldn't matter if it did fall in the water, it floats, thankfully. I was leaning over, deploying the motor today and it ripped the remote off my neck and into the water, I just floated over and grabbed it and it was fine.
Yep you are correct it does float and it still floats with the stronger lanyard holders that won't break
Mine broke and I made the same type of repair that you did the first time . Definitely a flaw
Get one of those kits and it won't happen again. I knew I wasn't the only one that had a problem! Thanks for the comment!
Hello from New Mexico. Do you like the fob for control? At times I wish both hands were free. Just ordered the wireless foot pedal. Have you tried it? Good job on the video, BTW.
The fob isn't perfect for sure. There are plenty of times I have to use it when I really need to be working the rod. Would love to hear your feedback on the wireless foot control and your set up. Thanks for the kind words too!
Also, the remote isnt waterproof, and wont float. Fill the inside completely with cheap silicone caulk. Holds the batteries in place and keeps water out. Silicone is easy to pull out when its time to change batteries.
Mine floats, at least for as long as I have allowed it too. Love that silicone idea!! Thanks for sharing!
Awesome video!
Thanks Mark!
Thank you sir!
I would not go so far as to call it 'a piece of crap", but I understand the frustration! I would have contacted MG directly to drastically improve your chances of actually getting MG to improve the product vs just belly ache over it behind the scenes. Each to his own, but I think it is crappy idea to chose the hand remote over the wireless foot pedal in the first place! The foot pedal is extremely light, effort less to steer (no cables like the useless clunker hard to steer cable driven models! MOST important IT FREES UP Both HANDS for the task at hand..Catching Fish! FISH ON!
Not many kayakers are running the foot pedal due to stability. But if you are able to do it, good on you. By the way, motorguide did improve it by making the piece that breaks a bit thicker but it's still going to break. Thanks for your input
Why anyone wouldn't rather use the WIRELESS pedal is beyond me.
@@Fishin1AZlol I don't know where you're from, but LOTS of guys who run the xi3 in the Hobie BOS use the pedal. If you are comfortable standing and fishing, using the pedal is a no brainer.
@@bradleyrussell1973 I've only see one with a foot controller but I would agree it would be a great option!
Nice bird lol, did you think I wouldn’t notice?
Hahaha that's funny. It's a bad habit!
Mine broke too.
I think most will at some point
www.tkicnc.com , Also a similar one can be found at www.etsy.com/shop/ferrousmetalworksllc
No kill switch in a Yak, think again!
You are correct. I do have the controller attached to me and I always have that life vest on.
I don’t want a kill switch in my kayak. If I fall out and can’t get to my kayak, I’m screwed. I’d rather be able to drive the kayak back to me. This isn’t a powerboat.
@@XploreAz Sure are putting a lot of faith in that controller? When the yak is upside down you're "controlling" nothing and yet the motor is still running! When you right the yak while the motor is running (assuming you don't get chopped up) how do you intend to get back in as the yak launches the second the prop hits the water?
@@fishntools well if the kayak is upside down, it’s not going to be driving away from me, so I guess it doesn’t matter.
@@XploreAz It matters if the prop is still turning.