First off, thank you for all of your fantastic videos! I have spent about 12 hours redo-ing this lab, and everything looks good, then DHCP fails on PC-B. I just noticed that on Part 1, step 9, show intf trunk, my lab has vlan 100,200,100 in STP forwarding state for f0/5,...While your 'show intf trunk' shows 'none' under spanning-tree fwd mode. I can't figure out what I'm doing that's different. Typically I write down what I think all the correct steps should be, then compare to you before going into virtual lab. My steps seem all the same as yours (some I didn't have correct before checking your video, great learning tool you're providing). If you have any suggestions, I'd love to hear. I believe I can do 'no spanning-tree vlan 100,200,1000', but I still wonde how I have different results from you. Much thanks.
Hello, thank you, for now the only way to practice is repeat all, be careful all switches should have the same vlans and the same native vlan on trunks
@@romeroc24 thank you, but no idea of how my vlans would be in a different STP mode than yours, after following same commands and configuration?? Again, thank you so much for the great instruction. Also, your excel chart for subnetting confuses me. Mine is simpler, Maybe I can show if you want, but clearly you already have it figured out. I just don't quite understand some of your layout. Either way, still, thank you so much. Obviously you put a lot of time and care into this
@@romeroc24 Will do. It is amazing how much time you put into this. You put more effort in than my professor. I hope you are being paid . I'll upload it. if you have time to take a look, that would be great
Can I do the dhcp excluded and pool from router 2 instead? Will that work? Like doing one pool on one router and another one in the other? O I have to add both pool in one router in order to work for both? I don’t know if I explained myself correctly. Awesome video by the way.
This is a helpful video! Got me out from commands I was stuck, thank you so much. Although I am curious, connecting crossover cables for router-to-router connection is just optional too right? But newer routers allow for connection with straight through to other new routers?
I know im randomly asking but does someone know of a way to get back into an Instagram account..? I was stupid forgot the password. I would love any assistance you can give me.
the lab doesn't work for me I did exactly the same as you until part 2 step2 and I always get the error DHCP failed APIPA is being used any idea what it could be?
@@romeroc24 I just found it the pdf tells us to use the something221 router, I used the something331 router but I Needed to use the something321 router I don't know if that was the main problem 😀
First off, I so appreciate all these videos you have made. I found you here in CISCO 1 and now I am back for CISCO 2 and I'm sure 3 when I get there. You have helped soooo much. Second, I'm doing this lab on packet tracer at home and I'm at the part where I need to input on R1(config)# ip route 0.0.0.0.0.0.0.0 10.0.0.2 & R2 (config)# ip route 0.0.0.0.0.0.0.0 10.0.0.1 and it will not work. it keeps telling me invalid input detected at ^ maker and it's placed under the first 0, this happens on both routers. I am going to stop for now to see if you respond. I did make the IP chart and filled in the IP address's on the lab sheet also step by step to this point. Help please, if you can. Thank you!!!
Christian Augusto Romero Goyzueta oh man I have spent a few hours on this lab. I can’t believe that’s all it was. Thank you very much Christian. You rock!!
well here I am again. This lab has been hell. At time 53.17, PC-A IP Address should be showing 192.168.1.6, but that is not what mine is showing. It is showing 169.254.53.116. I redid the steps, I lost count. I clicked on static then back to DHCP and it wont change. PC-B worked fine and I have the right IP Address on that pc. I don't know what to do, but start all the way from the beginning.
Thank you for the video helped guide me through a lot. When I issue the ipconfig /renew command on pc B it says unable to connect to DHCP server, timed out. I'm on NetLab, could it be because im using Chrome or do you have any idea why it would say that? Pings are all successful, did this as well on 8.5.1 DHCPv6 kept on timing out.
Thank you very much. Keep up the good work.
I appreciate your comment, thank you
thank youuu so much i found you in the last night ur a life saver
Thank you for all your support my friend!!!!!
Very helpful again , thank you a lot sir
Always welcome, thank you
Thank you sir!
Thank you for all your support, thanks again
Hermano tus vídeos me ayudan mucho gracias.
Gracias por verlos, aprecio bastante tu mensaje
THANKS
Thanks to you
First off, thank you for all of your fantastic videos! I have spent about 12 hours redo-ing this lab, and everything looks good, then DHCP fails on PC-B. I just noticed that on Part 1, step 9, show intf trunk, my lab has vlan 100,200,100 in STP forwarding state for f0/5,...While your 'show intf trunk' shows 'none' under spanning-tree fwd mode. I can't figure out what I'm doing that's different. Typically I write down what I think all the correct steps should be, then compare to you before going into virtual lab. My steps seem all the same as yours (some I didn't have correct before checking your video, great learning tool you're providing). If you have any suggestions, I'd love to hear. I believe I can do 'no spanning-tree vlan 100,200,1000', but I still wonde how I have different results from you. Much thanks.
Hello, thank you, for now the only way to practice is repeat all, be careful all switches should have the same vlans and the same native vlan on trunks
@@romeroc24 thank you, but no idea of how my vlans would be in a different STP mode than yours, after following same commands and configuration?? Again, thank you so much for the great instruction. Also, your excel chart for subnetting confuses me. Mine is simpler, Maybe I can show if you want, but clearly you already have it figured out. I just don't quite understand some of your layout. Either way, still, thank you so much. Obviously you put a lot of time and care into this
@@scottspa74 also you can send me your packet tracer file using social networks shown on 00:03
@@romeroc24 Will do. It is amazing how much time you put into this. You put more effort in than my professor. I hope you are being paid . I'll upload it. if you have time to take a look, that would be great
@@scottspa74 ok very nice
Can I do the dhcp excluded and pool from router 2 instead? Will that work?
Like doing one pool on one router and another one in the other?
O I have to add both pool in one router in order to work for both?
I don’t know if I explained myself correctly.
Awesome video by the way.
you can use dhcp excluded and pools on two routers or more, just only be careful with the subnets and excluded addresses
This is a helpful video! Got me out from commands I was stuck, thank you so much. Although I am curious, connecting crossover cables for router-to-router connection is just optional too right? But newer routers allow for connection with straight through to other new routers?
you alright, MDI and MDIX technologies permit this new feature
@@romeroc24 Woaa, thanks sir! Following more contents like this!
@@aurelvlaicu_c45u4l thank you
I know im randomly asking but does someone know of a way to get back into an Instagram account..?
I was stupid forgot the password. I would love any assistance you can give me.
@Kingsley Ayden Instablaster =)
Hi Sir, can i get the finish product file? The packet tracer app is not compatible on my cellphone :(
you can use a PC or Mac
the lab doesn't work for me I did exactly the same as you until part 2 step2 and I always get the error DHCP failed APIPA is being used any idea what it could be?
be careful with the dhcp specifications, an incorrect range of excluded addresses or incorrect network may cause that
@@romeroc24 I just found it the pdf tells us to use the something221 router, I used the something331 router but I Needed to use the something321 router I don't know if that was the main problem 😀
@@stijnpaepe652 Please try again from the scratch, it is better than troubleshooting
Hola¿ porque cuando quiero hacer pin desde la PC-A a la PC-B no reconoce al host?
verifica el enrutamiento, si no está presente, debe configurarse para hacer la conectividad
Si que me ayudó mucho, podrías también subir la practica de lab. 16.5.2 y 17.8.1?. muchas gracias!
OK lo haré esta semana
Thanks man ❤
You're welcome 😊 Thank you my friend
First off, I so appreciate all these videos you have made. I found you here in CISCO 1 and now I am back for CISCO 2 and I'm sure 3 when I get there. You have helped soooo much. Second, I'm doing this lab on packet tracer at home and I'm at the part where I need to input on
R1(config)# ip route 0.0.0.0.0.0.0.0 10.0.0.2 & R2 (config)# ip route 0.0.0.0.0.0.0.0 10.0.0.1 and it will not work. it keeps telling me invalid input detected at ^ maker and it's placed under the first 0, this happens on both routers. I am going to stop for now to see if you respond. I did make the IP chart and filled in the IP address's on the lab sheet also step by step to this point. Help please, if you can. Thank you!!!
0.0.0.0 (space) 0.0.0.0
Christian Augusto Romero Goyzueta oh man I have spent a few hours on this lab. I can’t believe that’s all it was. Thank you very much Christian. You rock!!
@@dinman68 I appreciate
well here I am again. This lab has been hell. At time 53.17, PC-A IP Address should be showing 192.168.1.6, but that is not what mine is showing. It is showing 169.254.53.116. I redid the steps, I lost count. I clicked on static then back to DHCP and it wont change. PC-B worked fine and I have the right IP Address on that pc. I don't know what to do, but start all the way from the beginning.
you can send me your file using social networks shown in 00:03
Christian Augusto Romero Goyzueta the PT lab file?
@@dinman68 yes
@@romeroc24 I sent it to your email. Thank you for looking at it.
@@dinman68 ok
No tienes una versión en español de este video?
no, pero por ahora puedes usar la traducción automática
No me dejo aplicar ip route:(
bueno , talvez el dispositivo que usas no es el mismo que yo estoy usando, verifica algunos detalles desde el inicio del video
Tienes el archivo pkt? Me lo podrías compartir por favor?
Puedes usar el video para crear tu propio archivo
Please send packet tracer file
You can follow all steps to create your own file
can you send the excel sheet please? btw...your videos help me so much! thanks!!
this is the file drive.google.com/file/d/0B0PJN0z8d6HRdFVQRVYzNmxmNWM/view?usp=sharing
@@romeroc24 Thank you!
do you have a video to configure firewall settings?
firewall on router with access lists or ASA firewall?
Christian Augusto Romero Goyzueta I’m not too sure. It’s on the Packet Tracer 6.1.4.7 - Configure Firewall Settings on Cisco Packet Tracer
@@MaverickReviewss please send me the file to romeroc42@gmail.com
Thank you for the video helped guide me through a lot. When I issue the ipconfig /renew command on pc B it says unable to connect to DHCP server, timed out. I'm on NetLab, could it be because im using Chrome or do you have any idea why it would say that? Pings are all successful, did this as well on 8.5.1 DHCPv6 kept on timing out.
on NetLab be sure switches not have the dhcp snooping activated in a a previous lab
Oye christian me puedes dar tu correo y lo revisas por favor
puedes usar las redes sociales mostradas en 00:03
Thank u Sir!
Most welcome! Thank you for all your support