Hi.. I have a Xiaomi dreametech and stopped working because it took like a spoon of water, it charges but doesn’t move. Don’t know if it completely damaged.
Thank you for these videos! I feel like I've watched every video having to do with mopping, as I'm having issues with my 950. I've taken it apart and checked the pipes for blockage, made sure there isn't a pressure issue in the reservoir, checked the pipe in the reservoir to make sure it wasn't blocked, made sure the inlet wasn't damaged...nada. Is there any way to test the water pump to see if it even cycles? I have no issue taking this guy apart again if it gets it mopping again. :) It's a life saver.
😅😅😅 ok ok.. sometimes pump motor just jammed so what you can do..use 9-12 v any charger & give that connection directly to motor only...plz disconnect motor before doing all this experiment... give this connection only for 3-4 second only... twice..if motor start working then assemble back.. should work...but it can spoil again..try ur luck
I think in my case the problem is the pump because following your suggestion in my case seems that the water flow in the three hole present in the water plate
@@ecovacstechnicalsupport5278 how is possible to fix my T8 water tank pipe like? Is possible to open the water thank to change the part into it? Thanks
What happens when that hose inside the mopping tank comes off? It's just floating inside the water in the tank. Is there a video on how to pull apart the tank without damaging it so I can replace? Mine is still under warranty anyway, perhaps it is better to take to the shop for a replacement.
@ecovacstechnicalsupport5278 Hi can you tell me if the pump of the deebot950 is the same of the deebot T9PLUS?? Or the two pump are different in power?
My n10 Robo is not mopping properly. It is overlapping the map, and when I reset the map now, it is not tackling the small obstructions like some small foot Mat or any other thing comes in way it does not go back to the mapping, rather start rotating and moving in circle direction over there, could you tell me the reason I have deep cleaned also?
I have purchased deboot N10 recently... Bt its not mopping properly and am not getting it resolved bt the ecovas technician also....its leaving a gap in btwn while moppings ... I can see yhe lines on floor while mopping... Please can u guide me in this
Hi Sir, thanks for the video. For T8 Aivi I already changed a new water pump, but water still has not been dispensed. May I know how to fix it ?. I'm so glad if you can answer me. Thank you.
Hi, thanks for your videos - very helpful. I have a slightly different issue, wondering if you have any advice? My OMNI X1 leaks water from underneath the base station when filling. It seems to fill up the actual vacuum itself, then then it speaks an error saying "Cleaning sink is dirty, please clean" or similar (but it very clean). About 2-3 seconds later it says "problem cleared, can continue (or similar). I press the Play/Go button and it does continue and I can see the clean water tank dropping, except that about half of it goes into the vacuum, and half leaks out the station. I had a closer look and it's leaking from directly underneath the base station (i.e. not inside the docking space). Any ideas or suggestions from your experience would be greatly appreciated.
@@ecovacstechnicalsupport5278 - Yes I'm quite certain what you have described is what needs to happen and is what would resolve my issue. I'm just wondering how difficult it is to open the whole station up to do this (being careful of course)? Interested to hear your opinion/thoughts with what you've seen and worked on in the past. Appreciate it.
Hi, I have Ozmo 950 unit and usually when I install the mopping the the reboot says that the mopping plate is installed, but all of a sudden it stopped mentioning it and as a result it doesn’t mop. What might be the issue.
Check the mop plate lock got a small magnet is it there...or inside the deebot next to water pump a sensor might be came off from its place or damadged
Good one. Fixed my deebot by disasembling and testing the pump plumbing. Thanks for sharing. As always some redundant screws are left :)
Welcome
I can confirm --> As always some redundant screws are left :)
I have the same problem. Where did you order the water plate from? I am in Europe so any help would be apprciated.
Hi.. I have a Xiaomi dreametech and stopped working because it took like a spoon of water, it charges but doesn’t move. Don’t know if it completely damaged.
Dear Sir, can you share the link or website where to buy the plate?
Thank you for these videos! I feel like I've watched every video having to do with mopping, as I'm having issues with my 950.
I've taken it apart and checked the pipes for blockage, made sure there isn't a pressure issue in the reservoir, checked the pipe in the reservoir to make sure it wasn't blocked, made sure the inlet wasn't damaged...nada. Is there any way to test the water pump to see if it even cycles? I have no issue taking this guy apart again if it gets it mopping again. :) It's a life saver.
😅😅😅 ok ok.. sometimes pump motor just jammed so what you can do..use 9-12 v any charger & give that connection directly to motor only...plz disconnect motor before doing all this experiment... give this connection only for 3-4 second only... twice..if motor start working then assemble back.. should work...but it can spoil again..try ur luck
Actually Is the old pump working or not? Can you unclog the hose and use the pump?
How to purchase n8 water tank?
Hi is possible to check it the pump is broken wiring with some power source? Thanks
Actually that's not possible to break any wiring...if wheels we can understand because they always turn got vibrations...but pump neve wiring issue
Thanks but i i disassembly the pump can I attach the pump to some power source like a 12 volts buttery to check if the pump is working or not?
Regards
Hi what’s the correct name of the plate that are you replacing? I would try the same on my T8. Thanks
We call it water plate..
I think in my case the problem is the pump because following your suggestion in my case seems that the water flow in the three hole present in the water plate
@@ecovacstechnicalsupport5278 how is possible to fix my T8 water tank pipe like? Is possible to open the water thank to change the part into it? Thanks
What happens when that hose inside the mopping tank comes off? It's just floating inside the water in the tank. Is there a video on how to pull apart the tank without damaging it so I can replace? Mine is still under warranty anyway, perhaps it is better to take to the shop for a replacement.
Water tank is sealed. Can not open . If under warranty then plz just request for ur warranty claim..
@ecovacstechnicalsupport5278
Hi can you tell me if the pump of the deebot950 is the same of the deebot T9PLUS??
Or the two pump are different in power?
Pump is same
So vac and yeedi brand are same pls let me know❤ from india
Some parts looks like same but I received for repair..some parts are different from ecovacs
My n10 Robo is not mopping properly. It is overlapping the map, and when I reset the map now, it is not tackling the small obstructions like some small foot Mat or any other thing comes in way it does not go back to the mapping, rather start rotating and moving in circle direction over there, could you tell me the reason I have deep cleaned also?
Try to clean as all sensors.. specially Front bumper n top black cover glass
I have purchased deboot N10 recently... Bt its not mopping properly and am not getting it resolved bt the ecovas technician also....its leaving a gap in btwn while moppings ... I can see yhe lines on floor while mopping... Please can u guide me in this
I also have Ecovacs N10, it's normal, just go to settings and put mopping water to high level, then you won't see the gap.
Hi Sir, thanks for the video. For T8 Aivi I already changed a new water pump, but water still has not been dispensed. May I know how to fix it ?. I'm so glad if you can answer me. Thank you.
Plz WhatsApp a video clip at this no. +601137973018
Hi, thanks for your videos - very helpful. I have a slightly different issue, wondering if you have any advice? My OMNI X1 leaks water from underneath the base station when filling. It seems to fill up the actual vacuum itself, then then it speaks an error saying "Cleaning sink is dirty, please clean" or similar (but it very clean). About 2-3 seconds later it says "problem cleared, can continue (or similar). I press the Play/Go button and it does continue and I can see the clean water tank dropping, except that about half of it goes into the vacuum, and half leaks out the station. I had a closer look and it's leaking from directly underneath the base station (i.e. not inside the docking space). Any ideas or suggestions from your experience would be greatly appreciated.
I received one case similar to ur....but after I open the whole station... reconnect all pipe line & general service..after that tested no leakage...
@@ecovacstechnicalsupport5278 - Yes I'm quite certain what you have described is what needs to happen and is what would resolve my issue. I'm just wondering how difficult it is to open the whole station up to do this (being careful of course)? Interested to hear your opinion/thoughts with what you've seen and worked on in the past. Appreciate it.
Can we use the detergent that Deebot has for the new models on the model you repaired?
I don't recommend...even for new model also I don't recommend..as a technician I know which part will spoil in few months if we use these detergent
Can we use detol or some disinfectant with water?
I don't recommend bro... because daily I receive many deebots using detergent, detol, liquid soap etc... got water tank n pump issues
Hi there. My deebot ozmo t9 no vibration while mopping. How to fix this issue?
Ozmo connector need to replace
Hi, I have Ozmo 950 unit and usually when I install the mopping the the reboot says that the mopping plate is installed, but all of a sudden it stopped mentioning it and as a result it doesn’t mop. What might be the issue.
Check the mop plate lock got a small magnet is it there...or inside the deebot next to water pump a sensor might be came off from its place or damadged
Sir, where are from, can we send machine to you. Are you the official support for ecovacs india
I'm from Pakistan.. working in Malaysia since 2013
Send me the screw driver details
Any screw driver can use..
Hi Sir, I have the same issue, Can please ping me the what’s app details