You should have slowed down and emphasized more on the electronics, explain a little bit more what everything it is used for and where everything should be soldered.... cause some of us lack all the knowledge you have. I would love to do this for my gokart but, it seems very dificult without those clear indications. Anyways, thanks for the video and nice job.
maybe on Instructables page might help, I'm not professional so I'm sorry for that, I still learing how to make perfect tutorial videos or project vlogs
You can actualy just tap into the timing wire and manipulate the timing from there, the mosfet will be able to handle it better, but id still use relay, specifically a solid state relay, because its faster and more precise.
Timing wire? You mean crankshaft position sensor? On FI engines it doesn't work it will mess up the counter for ignition and injector timing and check engine light will turn on because on FI engines there are multiple teeth with 1 missing or more on magnet / crank teeth, only engine with CDI works
That little coding Sequence looked very professional. I'll try stroking my keyboard like that too 🤣 but in all honesty, this is a nice project, want to try something similar too!
Watch the video, looked at your instructables page, I have a couple of questions 1) without a display how do you set the delay? 2) watching the video there is a gear up message on the screen, is this some kind of gear shift warning light? 3) How go I get the code and circuit diagram for the display version.
Wow!! Dude.... What a great DIY work you did right there?? I wish to be that smart as you are... I have a cbr 125r carburetor and I'm wandering if I could do the same thing.. And I have a Honda Astrea Dream with a monster motor 150cc on it and I have a wrist problem, so I'm wandering the same thing if I can do it to my astrea too... Do you know??
Yg kayak begini baru mantab di subscribe. Gak pelit ilmu gak pelit code. Nyumbang saran mas lebih mantab lagi di perseneleng operan giginya tambahin switcer starter mobil carry. Jd ngoper giginya pke tombol biar gak terlalu capek kaki.
robbykhen itu udah lumayan 30A kalo ga salah, lagian ribet Pake gituan harus bener negatif positifnya, ada relay bisa bolak balik kenapa diambil pusing
Hi, I'd like to try the version with lcd screen, do you still have the schematic diagram for that version? I also saved the code for lcd version for the last five years , please respond Thanks😊
I have a question, the clutch cable is it a positive connection from 12 volts battery? and I noticed from your schematic for Carb System bike with CDI you added a switch sign for the clutch switch? where does it connect?
Excelent job, Thanks. I habe a question, the squematic where are the conexon of cable C and NC of relay, you say conect "to your motorcycle", I suposse that C conect to the ignition coil but what is the conexion of the other (may be ground?)?
So, ignition coil cable usually has 2 cables on injection motorcycle, except Kawasaki KLX 250 had 1 cable. If there is 2 cables, select 1 cable and unplug, connect it into Common pin on relay, and connect the coil into Normally Closed pin on relay. If there is only 1 cable just select that cable (Low voltage cable or input, not high voltage or output)
Bang saya udah ikuti tutorial nya tapi kok setelah selesai ,begitu switch nya di tekan relay nya cuma berfungsi 1x aja setelah itu di tekan lagi tidak berfungsi. Harus nyala matiin kunci kontak lagi itupun cuma 1x doang l.
di relaynya dikasih kapasitor / dioda ga buat nahan lonjakan listrik dari relay? kalo ga arduino nya suka hang atau kasih kapasitor 220uF 16v di 5v arduino
unfortunately, i have lack of knowledge about ignition timing and it will be high risk doing so. it might knock or even worse piston connecting rod will be bent and maybe crankcase will be exploded if timing was off couple degrees or milliseconds at high revs or rpm. since I don't know much about Arduino AVR timer it will gonna be so hard for me. I also want to make ECU or ECM but there is open source project called speeduino so i do not have to write from scratch.
Sorry brother, so many people struggle with the lcd version because some lcd have different address even with same model and color and I forgot where I place the original code ☹️
@@KazemitoHaruhi no worries :) one thing to ask. the potentiometer on the diagram (the one you called "trimmer), is it the one responsible for adjusting the delay of the ignition cut-off?
Hi there, is it safe for the module if you’re not adding stepdown module for a long term use? As we know, the voltage from the motorcycle is 12v-14v. And the arduino only need 5v-6v. Thanks in advance
Hi, the circuit can be installed on a svartpilen / duke 390 Efi ecu, only by disconnecting the black cable of the ignition coil using a hall sensor connected to the pedal crank as a switch? can you post the file to be uploaded to arduino? I thank
Hii sooo I have a 200cc carburated bike and I used one of those limit switches to disconnect the coil and put the switch on right Handel bar and it works fine similar to the setup u are talking about
Bro instead of connecting quick shifter switch to ignition coil can we connect to engine kill switch (because in my bike there are 2 ignition coil name primary coil and secondary coil, primary coil has 2 spark plugs where has secondary coil has 1 spark plug ) plz reply me bro
@@KazemitoHaruhi no there no EFI in my bike it is pulsar as200 single cylinder 3 spark plug engine! Will it work on this perfectly on this bike? Plz reply
@@shravanbpatil007 Pulsar will work just fine, just connect it using kill switch if you want make it simple. If you want harder method, cut the supply cable to the cdi or cable from crank position sensor and connect it to the quick shifter
@@KazemitoHaruhi one last question..do you think i can use delay timer module(with millisecond option/12vdc and 5v-30v relay) only without using arduino?or is it really necessary to use it?
@@KazemitoHaruhi sebelumnya makasih mas sudah share ilmunya. Ini ga bisa lebih cepet lagi mas? 10 ms gitu? Keterbatasan switch relay ya? Kalau pake mosfet mungkin ga mas sampe 10ms
Iwan Setyo Budi relay mentok 40ms, di video kan sudah dijelaskan kalo pake mosfet malah jebol mosfet nya soalnya nyambung nya ke koil bukan pulser, injeksi kalo pulsernya dimatikan beberapa milidetik aja malah ga bener pengapian nya, ga kaya motor CDI/karb
I have a kawasaki bajaj ns200 carb type, im not realy good with motorcycles but i love electronics and diy's, by the way is this quick shifter for carb type engine?
![[И.М.] Квикшифтинг, как оно работает](http://i.ytimg.com/vi/y72j7zwCsq8/mqdefault.jpg)
![[И.М.] Квикшифтинг, как оно работает](/img/tr.png)
Thanksss dude you are asommmm you chanel has the perfect mix betwen anime bikes and electronic
You should have slowed down and emphasized more on the electronics, explain a little bit more what everything it is used for and where everything should be soldered.... cause some of us lack all the knowledge you have. I would love to do this for my gokart but, it seems very dificult without those clear indications. Anyways, thanks for the video and nice job.
maybe on Instructables page might help, I'm not professional so I'm sorry for that, I still learing how to make perfect tutorial videos or project vlogs
You can actualy just tap into the timing wire and manipulate the timing from there, the mosfet will be able to handle it better, but id still use relay, specifically a solid state relay, because its faster and more precise.
Timing wire? You mean crankshaft position sensor?
On FI engines it doesn't work it will mess up the counter for ignition and injector timing and check engine light will turn on because on FI engines there are multiple teeth with 1 missing or more on magnet / crank teeth, only engine with CDI works
@@KazemitoHaruhiI think the timing wire he is saying is the primary coil that the ECU control.
the way you write code , got me
fighter s just old school joke man lol
That little coding Sequence looked very professional. I'll try stroking my keyboard like that too 🤣 but in all honesty, this is a nice project, want to try something similar too!
Great work man! I just finished installing a QS sensor on my bike the change is incredible!
Watch the video, looked at your instructables page, I have a couple of questions 1) without a display how do you set the delay? 2) watching the video there is a gear up message on the screen, is this some kind of gear shift warning light? 3) How go I get the code and circuit diagram for the display version.
I've ordered all thanks to you, hope i will make it work! Thank you
Wow!!
Dude.... What a great DIY work you did right there??
I wish to be that smart as you are...
I have a cbr 125r carburetor and I'm wandering if I could do the same thing..
And I have a Honda Astrea Dream with a monster motor 150cc on it and I have a wrist problem, so I'm wandering the same thing if I can do it to my astrea too...
Do you know??
Yg kayak begini baru mantab di subscribe. Gak pelit ilmu gak pelit code.
Nyumbang saran mas lebih mantab lagi di perseneleng operan giginya tambahin switcer starter mobil carry. Jd ngoper giginya pke tombol biar gak terlalu capek kaki.
tadinya mau pake hidrolik, jadi pake kompresor, tinggal pencet aja gausah injek pedal gigi. tapi mahal
Can u help me to make a
Gear shifter using button..
And sorry for my bad English..
Lol
use hall effect magnetic sensor, it's just easier to install :P
@@KazemitoHaruhi change gear without use your leg.. But tap a button.. Are u sure just use a sensor...
@@marmotorwork49 why u need my leg to change your gear? I still need ma leg.
Anyway, I'm not interested with it, it just make your life harder
@@KazemitoHaruhi hahahhaha lol OK tq kazemito 👍
yeay.... finally another worthy misqueen technique... keep it up cuy....
Mosfetnya nggak bisa cari yg ampernya lebih besar? Yg ke arah koil masih arus dc kan?
robbykhen itu udah lumayan 30A kalo ga salah, lagian ribet Pake gituan harus bener negatif positifnya, ada relay bisa bolak balik kenapa diambil pusing
would have been better if you explained how everything is working. What's actually happening.
Nice idea and circuit design... but man that soldering iron and hot glue is sketchy😂😂😂
I don't wanna use hot glue gun again, last time just 2 days after I bought one and that gun exploded.
Don't blame me if I use soldering iron.
Just buy a Pingel quick shifter fit and forget. They are cheap at 1,040 USA dollars. Do not mess around with this home made stuff that does not work.
Who said that's not work?.
For you it's cheap, for me? It's better buy something else with $1.000
Instead of using switch with spring as a trigger
can you use gear position sensor as a trigger?
Hi, I'd like to try the version with lcd screen, do you still have the schematic diagram for that version? I also saved the code for lcd version for the last five years , please respond
Thanks😊
Bang itu bisa di tambahin fitur launch control ?buatin tutorial nya yg pake launch control bang keren
no ariuno is required for this project
Mas kalo quick shifter agak keras gitu nyetting delay dan cut of nya di angka berapa yah mas yg enak?soalnya buat rpm tinggi rada keras dikit
Cutoff nya 70-80 aja coba
how much you charge to make couple of the eletronic box for me?
I made it but i have one question....clutch cable i will connect it to negative side of clutch switch or positive?
Do you know how i could connect to the pickup sensor, to get a rpm reading?
I have a question, the clutch cable is it a positive connection from 12 volts battery? and I noticed from your schematic for Carb System bike with CDI you added a switch sign for the clutch switch? where does it connect?
Cool, nice job. Sempat kukira channel luar
shiet i knew it from the accent... you're from indonesia ...
yang penting pintar!!
Excelent job, Thanks. I habe a question, the squematic where are the conexon of cable C and NC of relay, you say conect "to your motorcycle", I suposse that C conect to the ignition coil but what is the conexion of the other (may be ground?)?
So, ignition coil cable usually has 2 cables on injection motorcycle, except Kawasaki KLX 250 had 1 cable.
If there is 2 cables, select 1 cable and unplug, connect it into Common pin on relay, and connect the coil into Normally Closed pin on relay.
If there is only 1 cable just select that cable (Low voltage cable or input, not high voltage or output)
@@KazemitoHaruhi i plan to try igbt replace relay.
The brake light switch cant compress when you downshift. what is your solution to that?
no downshift feature on this project bro, if you want to downshift, you need servo motor to move the throttle. it's complicated
Can you please share the code that are you using
I make .. ..works 100% tks
Nice! Have a good day!
Make video of new version without lcd... i see in instructable. ;)
Link
Can you draw a diagram for Speedo tuner for motorcycles.
I just heard that product and haven't tried it yet, so I can't.
Maybe I can try to make one with Arduino
Bang saya udah ikuti tutorial nya tapi kok setelah selesai ,begitu switch nya di tekan relay nya cuma berfungsi 1x aja setelah itu di tekan lagi tidak berfungsi. Harus nyala matiin kunci kontak lagi itupun cuma 1x doang l.
di relaynya dikasih kapasitor / dioda ga buat nahan lonjakan listrik dari relay? kalo ga arduino nya suka hang atau kasih kapasitor 220uF 16v di 5v arduino
Diy programmable cheap cdi please
unfortunately, i have lack of knowledge about ignition timing and it will be high risk doing so.
it might knock or even worse piston connecting rod will be bent and maybe crankcase will be exploded if timing was off couple degrees or milliseconds at high revs or rpm.
since I don't know much about Arduino AVR timer it will gonna be so hard for me.
I also want to make ECU or ECM but there is open source project called speeduino so i do not have to write from scratch.
Pemutus arus pakek relay kah..????
What are the resistors used? Also, can you please post the picture of the breadboard up close? I am a little confused.
Yeah, hardcore coder try to speeding...cool bro
How to ruin a solder iron
Cypaubr that's just a cheap soldering iron so it's ok
hi. i'd like to try the version with the LCD screen. do you have the code for that version?. thanks!
Sorry brother, so many people struggle with the lcd version because some lcd have different address even with same model and color and I forgot where I place the original code ☹️
@@KazemitoHaruhi no worries :) one thing to ask. the potentiometer on the diagram (the one you called "trimmer), is it the one responsible for adjusting the delay of the ignition cut-off?
omg i don't know how to make it
Hi there, is it safe for the module if you’re not adding stepdown module for a long term use? As we know, the voltage from the motorcycle is 12v-14v. And the arduino only need 5v-6v.
Thanks in advance
If you read the schematic and datasheet of the Arduino, you will know there's built in 5v or 3.3v regulator connected to VIN pin at Arduino.
Is that mean, we dont need any stepdown module ?
@@muhammadilham6895 yes, with load no more than 900mA for safe usage (1A max for the regulator), that's why I use 12v relay.
@@muhammadilham6895 you still need external regulator if the load is greater than 1A
So you are using 12v relay ? But, in the schematic the relay is using 5v pin from arduino.
Any explanation for that? Coz im really confuse rn 😕
Can you build me one? How much $ do you want? Let me know please 🙏.
What country? I'm afraid shipping cost more than the device itself
Hi, the circuit can be installed on a svartpilen / duke 390 Efi ecu, only by disconnecting the black cable of the ignition coil
using a hall sensor connected to the pedal crank as a switch?
can you post the file to be uploaded to arduino?
I thank
Hii sooo I have a 200cc carburated bike and I used one of those limit switches to disconnect the coil and put the switch on right Handel bar and it works fine similar to the setup u are talking about
Dont use an hall sensor, they arent sensitive enough!
Hi bro...can u make it up for suzuki fxr150...with carburator.
it works with injection and carb bikes. try it.
Bisa matching dengan ecu brand ecushop untuk motor exciter 150?
Semua motor injeksi pnp kok udah di tes
You have update on this project?
No, last update maybe a year ago
Maybe you can give feedback for the sensor so I can make update
but its still good on fi engine? @@KazemitoHaruhi
Om bisa pesan ga buat GSX-R150
Abang dari Indonesia?
Betul
Bro instead of connecting quick shifter switch to ignition coil can we connect to engine kill switch (because in my bike there are 2 ignition coil name primary coil and secondary coil, primary coil has 2 spark plugs where has secondary coil has 1 spark plug ) plz reply me bro
You can, but if you using multi-cylinder efi bike it might trigger check engine
@@KazemitoHaruhi no there no EFI in my bike it is pulsar as200 single cylinder 3 spark plug engine!
Will it work on this perfectly on this bike? Plz reply
@@shravanbpatil007 Pulsar will work just fine, just connect it using kill switch if you want make it simple.
If you want harder method, cut the supply cable to the cdi or cable from crank position sensor and connect it to the quick shifter
@@KazemitoHaruhi tq very much bro, if it becomes successful means i will definitely say you ok 😉
@@shravanbpatil007 I'll always be ok if I still reading and replying comments on my videos. I'll not okay if I never come back
bro minta rangkaiannya dong sama kode programnya
Where do you connect the two switches for time scheduling
Thanks if you can help me
@@santiagorojas2124 i think you change time scheduling by changing the code, its no longer from the I2C led
Ini bisa pesen ga bro buat r25?
bang yg benar sambung ke 12v koil atau negatif koil
12v koil yang positip bang, positip kopit
Bro klo aq mau beli yg dah jadi bisa?
Work it gak.. ada yg tanpa relay jadi lebih slim
worth it, lagi dicoba bikin tanpa relay
@@KazemitoHaruhi ditunggu video yg tanpa relay broo
Bikin, terus jual di lupabapak gan
Bisa pesen ga bro? Kayaknya orang tangerang nih :v
Buat motor karbu bisa ngga bang?
Bisa
Maksudnya gmn ni? Masukin gigi pakai tombol?
tanpa tombol dan tanpa kopling, kayak motor balap atau moge
How should I do the coding part?
Buat motor karbu ga bisa ya
Bisa, udah dicoba dan work
bro kalo di 2 silinder gabisa?
Anggoro Sakti ngga, ini buat 1 silinder.
Mas pesen boleh...minta no konteknya....
kalau ke injak terus gimana mesinnyaa
Ya jangan diinjak dong, kasian mesinnya diinjak injak
Great work man! I finished it but haven't installed it yet. Does it support downshift?
No. Downshift need mechanical actuator to rotate throttle.
Thank you! I got it
mantaps
does it work for yamaha r6 2007 ?
Works on any bike. If your bike has 4 cylinders, use 2 dpdt relay, or 4 spdt relay
i have 4 cylinders @@KazemitoHaruhi
@@arabivideos6140 So, if you have 4 cylinders you have to cut the power to all CDIs. Please check your r6's wiring diagram
Halo bg
Anjir baru ngeh gw jdi quick shifter fungsinny matiin ignition , buat ganti coupling ngelepas cluctch ea , CMIW.
bikin laaaaaaaa, udah gua share gratis juga, asal jangan dijual belikan hehe
Pakai subtitel indonesia bang.. nggak paham
Di tombol caption nanti ditambahin bahasa indo
Ada Instagram gak bang ?
Di deskripsi ada tulisannya 😁
Hello i have problem when i press the botton the light is not working
If i release my hand the light works
Why
bisa pesan buatim om...keren..bisa buat s3ndiri
EKO SUSANTO boleh, tapi ga pakai layar ya.. ga tanggung jawab kalo layarnya retak diperjalanan, dan cuma kepakai sekali jadi sayang
Sirilus Realin Hardiyanto 170 tapi gak pakai layar, soalnya cuma kepakai sekali dan resiko retak diperjalanan
@@KazemitoHaruhi sy pesen 1 om
@@yayansudiana8698 motor apa? Karbu atau injeksi?
@@KazemitoHaruhi injeksi, new r15 vva
do you have schematic for r6?
Just connect it to engine kill switch in parallel
@@KazemitoHaruhi thank you..will try this
@@KazemitoHaruhi one last question..do you think i can use delay timer module(with millisecond option/12vdc and 5v-30v relay) only without using arduino?or is it really necessary to use it?
@@milecyclevlogs9106 maybe yes maybe no, you can try it if you want. but I don't think it will work flawlessly
@@KazemitoHaruhi again..thanks..:D
Bro,why u trolling with the keyboard...how to code properly
Adeknya Bayu skak yaa
Bisa pesan gak gan . Please jawab
roy rohman bole aja tapi ga pake layar ya..
@@KazemitoHaruhi minta WhatsApp nya hu
Dm aja dulu di ig
Cek DM Bang
How do you power the arduino?
Read the schematic.
Itu bisa di adjust ( di program) kan seberapa lama matiin pengapian nya
Khadafi Yusuf 40-150ms, paling mentok 255ms kalo minta ditambahin lagi
@@KazemitoHaruhi ouuu ms berarti milisecond ya bang berarti segitu sama aja berapa detik apa 0, sekian detik
@@KazemitoHaruhi sebelumnya makasih mas sudah share ilmunya. Ini ga bisa lebih cepet lagi mas? 10 ms gitu? Keterbatasan switch relay ya? Kalau pake mosfet mungkin ga mas sampe 10ms
Iwan Setyo Budi relay mentok 40ms, di video kan sudah dijelaskan kalo pake mosfet malah jebol mosfet nya soalnya nyambung nya ke koil bukan pulser, injeksi kalo pulsernya dimatikan beberapa milidetik aja malah ga bener pengapian nya, ga kaya motor CDI/karb
@@KazemitoHaruhi terimakasih mas Penjelasannya.
Can you make a rev limmiter?
I have a kawasaki bajaj ns200 carb type, im not realy good with motorcycles but i love electronics and diy's, by the way is this quick shifter for carb type engine?
Kazemito Haruhi no wories its not something that needs to be rushed :)
Dijual kaga bang?
Fahri breaker jualan mah ngga, kalo mau mesen bole aja tapi gabisa buru buru ya
@@KazemitoHaruhi berapa duit ngmng ngmng??
Fahri breaker motornya apa?
@@KazemitoHaruhi GSX R 150
Fahri breaker injeksi ya, paling ga pake layar mau? 170an lah kalo ga pake layar
Bro minta kontak person dong
@@KazemitoHaruhi untuk nanya nanya tentang arduino, coba cek dm instagram aja
@@KazemitoHaruhi udah kuliah ato masih SMA? Mau nawarin ngajar juga kalo bisa
@@KazemitoHaruhi kalo ga nge tutorin bikin project doang kalo ternyata gabisa bikin projectnya gpp, pkoknya bantu bantuin doang gitu. Gua bukan penipu -_- makanya buka dm instagram cek aja profile gua zz
cut that nails
@@user-ge9mt2pu6p hehe