excellent - thank you for this video - I had replaced the whole lens assembly and now there's no stress to drive by night... the OEM lenses were totally burned inside...
Just finished the projector lens swap and lemme just say this video helped ALOT; IN WHAT TO EXPECT. Especially the hidden screw that holds the HEADLIGHT lens besides just the butyl sealant. The headlight is very hard to pry open and takes a few trips to the oven to heat it up again. Also gotta watch how you pry it open cause it has to be in a straight motion if not you can twist and break the inside reflectors, etc. thanks again for the video. Keep up the great work.
I think the real culprit of such poor light output was the actual projector lens. Thank you for the video, I am tackling a projector lens replacement this week and this video helps a lot! Thanks
Hats off to you sir, That is one complicated retrofit, I have to say by just the number of bolts around that AFS system. Evox-R projectors look very basic, but for sure they will not be easily entertained in any housing & having said that they are a performer. Again, great work as usual.
Hi!just a quick question.If the headlight is an AFL one from a right hand drive car,and I wanna fit it on a left hand drive car,replacing the lense will fix the light direction issue?as UK healights are like this \_\_ while Europe is _/_/. What I mean,are this lenses built for left hand drive?Thanks!
I have a few questions: How is the rotational sensor handled properly? Will the headlight need an adjustment after this? (i mean the baseline adjustment which needs to be done with Star Diagnosis)
i have same issue in my escalade. I think its E55 projector and light output is almost non-exsistent. i think my bowl is burnt and should replace with evox-r
Great video, my Pacifica xenon lens are getting clouded. Looks like I have to do similar procedure to replace the lens. Do you know ifnthe Pac is using 2.5" or a 3" lens?
Hello do i need same wires adaptor for igniter for skoda superb 3u with factory xenon d2s and can you tell me what else do i need fort the job to retrofit evox r or evox r 2.0
I own an Opel Vectra C,2005, with bixenon-afl-cornering headlights.Having this kit installed,will it affect any of the functions?will the afl/cornering still work ok?because I assume this are diferrent lenses which don't do the afl job.
Hey @Retrofitlab, I have two questions please: 1. Why did you also change the lenses? Couldn't you just swap the whole assembly (lens and mirror) over with the old one? 2. I have the Vectra C with AFL. If I buy the EVOXR C1, will I need to make the exact same mods as in your video? Thank you!
The headlight is sealed with butyl. When butyl is heated it gets soft and can be opened and for it can be heated again for sealing the headlight. So no need for other sealant.
When you have changed te projectors it can be the sensor screw is tightened too hard. Otherwise probably an electrical problem with a sensor, maybe a dealership can help you finding the problem.
I had the very same problem. It appears that the sensor-alike red circle have to be tightened to the very same position when you fix it back. Not to mention that the position of the black bracket has to be the same. It worked for me. Remember to take a picture of this wheel when you are about to take it off.
combination of heat and uv rays burn bowls , if you use a higher wattage ballast , or a cheaper bulbs , the produce more uv rays the burning will happen quicker
The projector itself doesn't have a leveling motor, only the bi-xenon mechanism, the same as with original projectors. In general leveling is done on the complete inner part of the headlight, so that the high beam part also is adjusted.
@@TheHarooni Halogen (even with projectors) usually not. Cars with xenon are usually equipped with this system because a lot of countries have or had the rule xenon headlights needed to be self leveling.
depends what bulbs your using or if you have upgraded the ballast to higher then a 35 watt unit the burning will happen quicker , all projectors will burn , just a matter of time
i dont mean to be offtopic but does anyone know of a way to log back into an Instagram account? I was dumb lost the account password. I love any tricks you can give me!
@Diego Aarav Thanks so much for your reply. I found the site through google and im trying it out atm. Looks like it's gonna take quite some time so I will reply here later with my results.
excellent - thank you for this video - I had replaced the whole lens assembly and now there's no stress to drive by night... the OEM lenses were totally burned inside...
Thanks, good to hear 🙂
Just finished the projector lens swap and lemme just say this video helped ALOT; IN WHAT TO EXPECT. Especially the hidden screw that holds the HEADLIGHT lens besides just the butyl sealant. The headlight is very hard to pry open and takes a few trips to the oven to heat it up again. Also gotta watch how you pry it open cause it has to be in a straight motion if not you can twist and break the inside reflectors, etc. thanks again for the video. Keep up the great work.
I think the real culprit of such poor light output was the actual projector lens. Thank you for the video, I am tackling a projector lens replacement this week and this video helps a lot! Thanks
no it was the burnt bowl lol
Hats off to you sir,
That is one complicated retrofit, I have to say by just the number of bolts around that AFS system. Evox-R projectors look very basic, but for sure they will not be easily entertained in any housing & having said that they are a performer. Again, great work as usual.
This helped me clean the projector in my R500
Good to hear :-)
Yes it is :D
Hi!just a quick question.If the headlight is an AFL one from a right hand drive car,and I wanna fit it on a left hand drive car,replacing the lense will fix the light direction issue?as UK healights are like this \_\_ while Europe is _/_/. What I mean,are this lenses built for left hand drive?Thanks!
I have a few questions: How is the rotational sensor handled properly? Will the headlight need an adjustment after this? (i mean the baseline adjustment which needs to be done with Star Diagnosis)
Hi Alexander,
Could you mayeb send us an Email, There i can provide you with some more info on this topic.
info@retrofitlab.com
i have same issue in my escalade. I think its E55 projector and light output is almost non-exsistent. i think my bowl is burnt and should replace with evox-r
Yes, early model Escalde should have the E55 projector and yes it is a major upgrade for the old burned ones :-)
@@Retrofitlab thank you. This is the 2010 Escalade with OEM HID American spec
Great video, my Pacifica xenon lens are getting clouded. Looks like I have to do similar procedure to replace the lens. Do you know ifnthe Pac is using 2.5" or a 3" lens?
hello I would change the lens on my mercedes c w204 is which model to be put ? and dismantled the lighthouse is complicated ? Thank you
would it be possible to replace it on a Mercedes CLS W219 and instal a bigger BiXenon Lens with a better light? and keep it on stock DS2?
did you use a heat gun or a hair dryer? would a hair dryer work like that?
I am having the same issue on my R Class. How much do you charge for this service?
Do you have any direct replacement projectors for the 2010 Mercedes E coupe with ILS?
Sorry for AFS we do, but for ILS there is no replacement
Great video. But now I need the adapters to insert between the igniter and the evox bulb holder. Where can I find them? Thanks
Yes, thank you very much.I ordered the items...and now it works perfectly!!! :-)
Hello do i need same wires adaptor for igniter for skoda superb 3u with factory xenon d2s and can you tell me what else do i need fort the job to retrofit evox r or evox r 2.0
Retrofitlab What do you prefer more evox r or evoxr 2.0 and can you send me a foto or a link of this adaptor
Just by heating and reusing the same glue is that enough for a perfect seal ?
Yes, when the headlight is sealed with butyl it can be re-used. When it would be sealed with permaseal, new sealant (butyl needs to be used).
@@Retrofitlab Thank you very much !
At what temperature putting Valeo and Hella headlights?
I own an Opel Vectra C,2005, with bixenon-afl-cornering headlights.Having this kit installed,will it affect any of the functions?will the afl/cornering still work ok?because I assume this are diferrent lenses which don't do the afl job.
***** so basically the AFL focus and the cornering is given by a mechanism located where the lense is fixed?
***** I was lucky,the lenses and mirrors were dirty.Had them cleaned up and now the work perfect:)!
***** adg u ub
Hey @Retrofitlab, I have two questions please:
1. Why did you also change the lenses? Couldn't you just swap the whole assembly (lens and mirror) over with the old one?
2. I have the Vectra C with AFL. If I buy the EVOXR C1, will I need to make the exact same mods as in your video?
Thank you!
Thank you! But will I require to do the same modifications as in the video or not?
Where i can see pictures of rotational sensor, i have problem, my projector turn left and stay there
drzga did you find the solution for this? Same thing here!
I have the same issue, my Left lamp is stuck in left position.
Do you find solution?
In my W219 after repair projector light stuck in right side? If you find solution please replay
@@okejminjadid you solve this issue? I have the same fail
Why did you use same sealant? Is it ok? Still waterproof?
The headlight is sealed with butyl. When butyl is heated it gets soft and can be opened and for it can be heated again for sealing the headlight. So no need for other sealant.
My projectors turn left and stuck There. Where is problem?
Sensor?
When you have changed te projectors it can be the sensor screw is tightened too hard. Otherwise probably an electrical problem with a sensor, maybe a dealership can help you finding the problem.
@@Retrofitlab
Thank you
I had the very same problem. It appears that the sensor-alike red circle have to be tightened to the very same position when you fix it back. Not to mention that the position of the black bracket has to be the same. It worked for me. Remember to take a picture of this wheel when you are about to take it off.
Is the EvoX R 2.0 a direct instal on the 06-10 Mercedes R Class? If not, what projector is?
We would recommend the EvoX-R ECE or DOT :)
Please tell me where can I get pictures of rotational sensor correct position?
What is the correct position for the rotational sensor? I don't see a link for photos?
can we fix burned reflectors? like paint with spaz stix or alclad chrome colour spray.
thanks
Do you have video of replacement Volvo XC60 2012? Thanks
ua-cam.com/video/FcNgv0q9rsg/v-deo.html&ab_channel=Retrofitlab.com please check out this video!
I’m doing this! Thanks for the video👍👍
Nice! You are welcome :)
Retrofitlab.com Do the 2.0 projector need cutting like the one shown in the video?
@retrofitlab did you use any aftermarket replacement or the originals one ?
Thank you very helpful 👍
which torx screwbits you use ? T5 ?
Hi cane you add replace projector for w204 bi xenon? Plz add for w204 upgrate projector bi xenon.
:) please see this link: retrofitlab.com/collections/mercedes-c-class-w204
Hi, when you put the heat gun. At what temperature do you put it during the 12 minutes?
Thanks
Celsius o Fahrenheit?
Retrofitlab ok thanks
So what exactly causes the lenses to burn in the first place? are they just bad quality?
combination of heat and uv rays burn bowls , if you use a higher wattage ballast , or a cheaper bulbs , the produce more uv rays the burning will happen quicker
wher we can buy just back part reflector?
Hi, please contact the customer support of retrofitlab. They should be able to help you! info@retrofitlab.com
Hallo welche xsenon passen für r klasse ds1 oder ds2?
Beide Optionen sind mit der R-Klasse möglich, die 2010 von D2S auf D1S umgestellt wurde.
Evox-r 2.0 can be retrofited to such a system? I ve read that some modifications have to be done. Some tips please?
Yes, it is possible but needs a lot of custom work. The EvoX-R ECE or DOT is a direct install, we would recommend this one!
@@Retrofitlab so 2.0 are not exact like the e55? Like the 1.0 are? I tought they are exactly like the 1.0
@@caesar_rex, no they are slightly different..
y el ajuste de optic shield? puede que tenga problemas de fotometria
I'm interested in this kit. Does it have a self leveling motor?
The projector itself doesn't have a leveling motor, only the bi-xenon mechanism, the same as with original projectors. In general leveling is done on the complete inner part of the headlight, so that the high beam part also is adjusted.
@@Retrofitlab I currently have halogen headlights with projectors. Does that mean I will already have the self leveling mechanism then? thanks
@@TheHarooni Halogen (even with projectors) usually not. Cars with xenon are usually equipped with this system because a lot of countries have or had the rule xenon headlights needed to be self leveling.
Viewers thing this was sped up but he had three espresso's an hour before.
Are this Adaptive headlights or normal headlights?
Adaptive
What's the Durability/Time until this kind of Burn happens?
depends what bulbs your using or if you have upgraded the ballast to higher then a 35 watt unit the burning will happen quicker , all projectors will burn , just a matter of time
One of my projectors burned after 1 year 35W system. Other ones lasted many many years
can you tell me the exact type and model of the bulb please ? thanks
The bulbs that we've used are D2S xenon bulbs.
The secret for that light is not only the bulb, but the projector as well.
Just wrap the old reflector with chromed alu foil and use heat resist glue. Easy cheap and usable
+Mike Johansson, I can't believe it will be as good as a brand new projector.. Do you have some output shots? :)
Did this R got ILS lights or normal bi xenon?
Retrofitlab ok. I already have evox-r projectors and cables in my warehouse. im going to install those to my w211 merc. so its exactly same project.
Simpura69 hey did you install the evox-r projectors yet in your w211?
yes i did.
HAY QUE TENER BOLAS GRANDES PARA DESARMAR EL FARO DE UN MB!! CONGRATS! ITS BEUTIFULL
What size is that 2.5 inch?...
3" :-) www.retrofitlab.com/en/aharon-evox-r-bi-xenon-projectors-hella-design-2.html
These are the ones used in the all spyder prototypes?... if so thanks man you have been a real help 💯...
How do you know it’s 3inch tho I’m trying to see where it says that...
@@bossmanlos8850 Because we sell them :-) (also in the text: "The 3.0 inch crystal clear lenses")
@@Retrofitlab thank you 🙏🏻...
Podrías transformar los faros normales de un w203 MB por favor! Gracias!
i dont mean to be offtopic but does anyone know of a way to log back into an Instagram account?
I was dumb lost the account password. I love any tricks you can give me!
@Kian Kellen Instablaster =)
@Diego Aarav Thanks so much for your reply. I found the site through google and im trying it out atm.
Looks like it's gonna take quite some time so I will reply here later with my results.
@Diego Aarav It did the trick and I finally got access to my account again. I'm so happy:D
Thank you so much, you saved my account!
@Kian Kellen No problem :)
i can install on hyundai accent 2012
+Retrofitlab what's about q5
you can retrofit any headlight
Yeah fuck that. 1000 screws
i will keep using incandescent bulbs.
and have crappy lighting , go ahead lol
Lord of the rings ?? ;-)
Dio merda quanto e' complicato xo...
What a waste of time to remove a perfectly good OEM hid projector or an aftermarket one to get SLIGHTLY better light output.
The difference is more than 500%.. So that is more than slightly isn't it? :)
Remind me not to buy a Mercedes.
Any car with projector headlights