very good tutorial. Can you help with MAF of SKODA RAPID 2013 1,6 TDI 77kw? I ve bought a second MAF but always the same problem, blinking light on dashboard.
Hi I'm hoping you can help with an issue I have, getting a P0103 error, I've disconnected the MAF and tested using a multimeter as per the video and the middle pin doesn't seem to be receiving 12v, showing between 0.1 and 0.5 volts, 3rd pin showing 4.9-4-95 so no issue there, could this indicate an issue with the wiring itself rather than the MAF sensor?
My vw passat is chugging when i accelerating it only happens when the car temperature reaches 90. But engine is cold no problems.but when car is hot you can't drive it it chugging and cutting out when you accelerating. Have you any answers to my problem. Thanks
Hello from India, I drive a VW Polo 1.2 TDI driven for 150000kms till date from December 2011, 1. Firstly, my car doesn't show the thrust in the pickup as it used to show earlier like it threw us back in the seats while picking up , but now it has turned sluggish inspite of maintaining it very nicely. 2. Secondly, the mileage per litre has gone down inspite of driving with light foot and on low rpms. Should I also clean my MAF sensor? Will it help ?
On my Golf 6 1.6TDI Cayc i have the error n. P0101, i changed the maf senzor, nothing...check engine on the board but the car function correctly, it made also the regeneration...all...just check engine
You taught me so much on fixing my audi a4 🙏🏾
That's cool ! what else do would you like to see ?
very good tutorial. Can you help with MAF of SKODA RAPID 2013 1,6 TDI 77kw? I ve bought a second MAF but always the same problem, blinking light on dashboard.
Hi, my passat 2011 maf sensor only reads 10,000 ohm between pins 1 and 3 and no continuity between other pins does this mean the sensor is bad? Cheers
Super tutorial
Hi I'm hoping you can help with an issue I have, getting a P0103 error, I've disconnected the MAF and tested using a multimeter as per the video and the middle pin doesn't seem to be receiving 12v, showing between 0.1 and 0.5 volts, 3rd pin showing 4.9-4-95 so no issue there, could this indicate an issue with the wiring itself rather than the MAF sensor?
Nice
My vw passat is chugging when i accelerating it only happens when the car temperature reaches 90. But engine is cold no problems.but when car is hot you can't drive it it chugging and cutting out when you accelerating. Have you any answers to my problem. Thanks
Were you able to resolve this?
What was the fault error?my car shaking on idle nothing show me up.on tester
Hello from India, I drive a VW Polo 1.2 TDI driven for 150000kms till date from December 2011,
1. Firstly, my car doesn't show the thrust in the pickup as it used to show earlier like it threw us back in the seats while picking up , but now it has turned sluggish inspite of maintaining it very nicely.
2. Secondly, the mileage per litre has gone down inspite of driving with light foot and on low rpms.
Should I also clean my MAF sensor? Will it help ?
Yes it can help , so try to inspect the intake pipes for any residual oil and clean it
can a mass air flow sensor cause a no start?
no
Please do know that a Battery uses DIRECT CURRENT (DC) not AC.
On my Golf 6 1.6TDI Cayc i have the error n. P0101, i changed the maf senzor, nothing...check engine on the board but the car function correctly, it made also the regeneration...all...just check engine
did you find out the issue?
I háve problem with Passat B7 1.6 TDI (P2279)
Goog❤ 2:07