В целом очень понравилось. Уже присутствуют современрые технологии. Это хорошо, приятно смотреть, когда не из старых бочек сваренных электродами! И даже сварщики уже в масках, а некоторые даже в перчатках. Почти конвейер, пусть и с ручным приводом!
It’s great to see the old skills still being used. After 40 years in manufacturing, I still remember when it was done this way in the US. I can see some room for process improvement, like there are several steps where the part gets put down then picked up and put on racks. You’d save time by having more racks, but I’m guessing the labor cost is cheap so maybe efficiency isn’t the cost determining factor. Anyway, you have a great labor force and I’d happily hire any of these guys. Most young Americans can barely unwrap a Big Mac.
Finally, workers from Pakistan working on raised platforms, instead of squatting on the ground. Also good to see MIG and TIG welding, instead of the ubiquitous 'stick' welding that proliferates across many of these videos.
@@JayantSewtahal you can hire people to develop, design, market, sell...etc and let the robots deal with this type of work and have people do things robots can not do, you don't replace people but rather you elevate them to do much more sophisticated work than wasting their lives doing this.
Pre rusted brackets and tabs spot welded to the side of the frame? Ps Rusty steering head tubes. Pps after chemical dipping rust was still visible under the floor of the battery box as they were wheeled to the powder coating booth.
Quy trình sản xuất khung sườn xe mô tô gắn máy là đây từng công đoạn thứ tự rất khoa học xin chúc mọi người sức khỏe chăm chỉ làm việc đạt hiệu quả cao. ❤❤❤❤❤
Looks like an old Honda S90 frame, but better as the welding spatter is knocked off! (although original spot welding should be stronger as it wasn't butt welded along seam ) Being powder coated its actually better than the Japanese pressed frames form 1960's, particularly as they did spray inside battery enclosure.
I don't think they use the same steel as the original Honda, it even looks like even they use different steel for some of the frame components as they rusted already
You know I got to hand it to this country. I might be wrong but it looks like India. Correct me if I'm wrong but I got to hand it to that country. They make everything and anything way more of the United States and I live here in California and that's California. California can't make their own crap that they have to get somebody else to make their stuff for the United States. So my hat's off to this guys. Keep up the good work. Thanks for the video😢
These are most definitely almost identical to the original Honda SS50. This version uses the same frame but a 3 speed auto clutch 70cc version of the Cub engine. The SS50 was a very good bike. I wonder if they now have the licenece/tooling to be able to copy it?
Que legal nos anos 80 eu tive uma moto desse modelo só que éra 50 cilindrada eu sou do Brasil se viar aqui dessas Eu vou comprar uma prá mim adoro esse modelo de chassi
Pengurus kilang kedekut mengeluarkan sedikit perbelanjaan peralatan pekerja mereka. Kasut keselamatan, sarung tangan kulit, penutup hidung.. Sarung tangan yang mereka pakai tentu beli sendiri.. Jika kilang punya semua warna sama😂
البته باز هم اثر تحقیق و توسعه د ر روند تولید در این مستند هم متاسفانه دیده نمی شود ولی تجهیزات استفاده شده ومکان تولید قابل قبول است و بوی حرفی بودن و پختگی را میدهد (البته باز هم مسالئه ایمنی شایسته مردم سخت کوش منطقه ما نیست)
So many fundamental mistakes. Why they stake frames horizontally on top of the vertically frames during galvanizing is so wrong: the fluids remain inside, you see afterwards the wet floor. The powder coating is so wrong. They guy in grey touches everywhere. For such production rate they should use a line with baking furnace. The same grey guy bangs the ready coated parts on each other The pressings are bad: you see the dents ( and during pressing you see the toolings shift) The welding is so ad randomly Throwing frames on the floor?!?!? Grinding on the dirt floor, and all the grid flies everywhere The manual powder coating gives zero assurance of layer thickness and good surface cover in every corner On some moments you see the welders not using eye protection Banging with that steel hammer is proof of irregular toolings. He bangs on surfaces but there is no gauge measuring afterwards. Imho: i think that all welding can be done in 2 set ups with cheap robots. The handling of the presses is unnecessary with a magnetic lift. I wonder how the edge looks after the clipping operation, with worn out clipping tool no sharp cut but bended/ torn surface
Just to think that whole presentation is for a SINGLE motorcycle brand and specific CC. I cant imagine how much time you need to re tool to a different one😮😮.. 🤔🤔
@globalartiisans Honda design form the late 1960s. CL70 in the US. I have one now, and it still works well. A well engineered motorcycle for the cost. They are reliable transportation still in many countries.
Hoje as grandes empresas, usam mão de obra praticamente escrava e ainda fica gente batendo palmas pra isso. Quantos trabalhadores são mortos ou terão danos graves sem assistência das empresas. Isso é horrível e não algo para admirar.
To me the build quality and attention to detail seem very poor. Also this rough handling and rushed assembly don't help. That being said I think that the low production cost of these frames is unbeatable
Very good that all the workers are wearing their safety-sandals.
And their loosest fitting clothing.
dont making fun of them actually one of them much 10 of you you egnorent
В целом очень понравилось. Уже присутствуют современрые технологии. Это хорошо, приятно смотреть, когда не из старых бочек сваренных электродами!
И даже сварщики уже в масках, а некоторые даже в перчатках.
Почти конвейер, пусть и с ручным приводом!
It’s great to see the old skills still being used. After 40 years in manufacturing, I still remember when it was done this way in the US. I can see some room for process improvement, like there are several steps where the part gets put down then picked up and put on racks. You’d save time by having more racks, but I’m guessing the labor cost is cheap so maybe efficiency isn’t the cost determining factor. Anyway, you have a great labor force and I’d happily hire any of these guys. Most young Americans can barely unwrap a Big Mac.
Finally, workers from Pakistan working on raised platforms, instead of squatting on the ground. Also good to see MIG and TIG welding, instead of the ubiquitous 'stick' welding that proliferates across many of these videos.
Many steps are on the ground.
Grinding was on the dirty floor
Great work. How we used to be before we lost our way!
Loved how u did not use music ❤
The attention to detail, care and attention not given is amazing. Also what’s with Aqua man at 3:14
This is true of ESAF (enhance & smart architecture frame) Build Quality is no 1 👍 love from 🇮🇩
Respect 🫡
ini las nya bagus, kalo yg di tempat kita lasnya pakai las kanopi pakai elektroda
Seharusnya begitu proses nya, bnyak tahap.. Yg udah2 di Indonesia pada terbelah kropos krn habis di las langsung cat biar biaya produksi minim
@@irwaniswadidan di celupkan ke cairan anti karat,di Indonesia mungkin tidak di celupkan ke cairan anti karat 😁
@@olaartanakola ya smacam coating logam
awesome, cutting,stemping, welding,tapping, grinding, pre-treatment, painting until drying with oven
Respect 🫡
Powder coat, not paint.
Trabalhadores experientes fazem a diferença. Fazem arte com poucos recursos. Esses caras consegue tirar leite de pedras. Muito bons.
Why do Americans and Westerners always criticize Pakistani while most Russians admire the work done by Pakistanis here ??? Interesting 🤔
Om dat we goed kranten en TV hebben misschien?
Russians aren't used to quality products. A great percentage of Russians rely on Vodka for their good judgment.
Criticize? Hahahhahahahhaha😂😅😊😂😅😊😂😅😊😂 who told you ? Sleep.
Потому что у нас даже такого производства нет. А телевидение и газеты работают хорошо, делая людей идиотами.
Cause Americans are a holes.
Looks very pro,good work.
you guys make our robots look slow.great work
Thanks🫶🏻
I Hubble agree with you mine (if i can writing like thise) FRIEND.Thise kind off production is good fore Jobs fore many people instead off Robot.
robots belong to no one, they are a product of humanity. so it's a bit pretoncious to say ..our robots..
@@JayantSewtahal you can hire people to develop, design, market, sell...etc and let the robots deal with this type of work and have people do things robots can not do, you don't replace people but rather you elevate them to do much more sophisticated work than wasting their lives doing this.
I guess it's not obvious the video is at 2x speed
Pre rusted brackets and tabs spot welded to the side of the frame? Ps Rusty steering head tubes. Pps after chemical dipping rust was still visible under the floor of the battery box as they were wheeled to the powder coating booth.
They are so professional
Respect 🫡
Rangka esaf ini, ngga perlu gimik2 teknologi canggih, teknologi lama di gimik teknologi canggih kaya gimiknya adnoh
this guys in pajamas are skilled ..
En Venezuela podemos hacer cosas así de buenas también 👍😀
Quy trình sản xuất khung sườn xe mô tô gắn máy là đây từng công đoạn thứ tự rất khoa học xin chúc mọi người sức khỏe chăm chỉ làm việc đạt hiệu quả cao. ❤❤❤❤❤
powder coating without protective mask is wild😮😮😮
AHM harus nonton ini
Looks like an old Honda S90 frame, but better as the welding spatter is knocked off! (although original spot welding should be stronger as it wasn't butt welded along seam )
Being powder coated its actually better than the Japanese pressed frames form 1960's, particularly as they did spray inside battery enclosure.
Respect 🫡
Nobody pays attention to quality control, material specs., workmanship safety measures. A greed to become a millionaire in one day
I don't think they use the same steel as the original Honda, it even looks like even they use different steel for some of the frame components as they rusted already
excellent work in my beloved country. Well done keep it up.
Pakistan Zindabad ... Perfect ♥
Trabalho incrível, parabéns! Muito bom de assistir!
Amazing video
Thanks
También montaré mi fábrica viva Venezuela 💪💪🤨🤨👍👍
Chế tạo sườn xe rất là tuyệt vời ❤
First time frame video good work and keep it up👍👍👍👍👍
Respect 🫡
AMAZING
Bon courage 🇩🇿
Incredibly cool
Masahallah zabrdisat will don very nice good job made in Pakistan 🇵🇰🇵🇰💕🌹👍💐🏏🏏 zandaibad love from Iraq 💕🇮🇶🇮🇶🇵🇰🇵🇰💕🌹👍
Respect 🫡
You know I got to hand it to this country. I might be wrong but it looks like India. Correct me if I'm wrong but I got to hand it to that country. They make everything and anything way more of the United States and I live here in California and that's California. California can't make their own crap that they have to get somebody else to make their stuff for the United States. So my hat's off to this guys. Keep up the good work. Thanks for the video😢
This is Pakistan and all artisans are Pakistani respect 🫡
Good❤
Thanks❤️
Qual será o modelo de moto que usa esse quadro...
70cc Tezraftar
❤❤❤❤❤❤❤
Excellent
❤ Amazing Work 👍❤
Thanks
@@globalartiisans I'm From India 🇮🇳
@@saini_sahab_g_blogs respect 🫡
These are most definitely almost identical to the original Honda SS50. This version uses the same frame but a 3 speed auto clutch 70cc version of the Cub engine.
The SS50 was a very good bike. I wonder if they now have the licenece/tooling to be able to copy it?
Good work ❤❤❤
Thanks🫶🏻
Show! Show! Parabéns!
Hello,me dear friend! I am a motorcycle seat cushion factory,we are the supply manufacturers.😀
@Yitai788 Please share your contact details at pakartisan96@gmail.com
Thank you for your reply, I have successfully sent you an email.@@globalartiisans
Informative.
Thanks❤️
Keep it up .
🫶🏻
At about 14:00 or so, one of the tanks looks like it might be dilute phosphoric acid - gets any rust down, and helps paint, etc. bond.
Que legal nos anos 80 eu tive uma moto desse modelo só que éra 50 cilindrada eu sou do Brasil se viar aqui dessas Eu vou comprar uma prá mim adoro esse modelo de chassi
Please make video of tubular chassis or back bone frame making video of two wheeler
E’ incredibile come lavorino senza i più elementari dispositivi di sicurezza 😮
Pengurus kilang kedekut mengeluarkan sedikit perbelanjaan peralatan pekerja mereka. Kasut keselamatan, sarung tangan kulit, penutup hidung.. Sarung tangan yang mereka pakai tentu beli sendiri.. Jika kilang punya semua warna sama😂
top,
Me gusta cuando todo lo tiran al piso
9:41 "hey look at him. he think hes professional"
"hehehe"
Local idea but perfect .
البته باز هم اثر تحقیق و توسعه د ر روند تولید در این مستند هم متاسفانه دیده نمی شود ولی تجهیزات استفاده شده ومکان تولید قابل قبول است و بوی حرفی بودن و پختگی را میدهد (البته باز هم مسالئه ایمنی شایسته مردم سخت کوش منطقه ما نیست)
Het is gewoon slecht, en al die handjes van arme mensen die elkaar zowat verdringer.
پاکستانی کاریگر زندہ باد
Respect
đây có phải là khung sườn xe Honda 67 không..? loại xe này ở VN đem nấu phế liệu lâu rồi, loại xe ngó chướng con mắt…!
So many fundamental mistakes. Why they stake frames horizontally on top of the vertically frames during galvanizing is so wrong: the fluids remain inside, you see afterwards the wet floor.
The powder coating is so wrong. They guy in grey touches everywhere. For such production rate they should use a line with baking furnace.
The same grey guy bangs the ready coated parts on each other
The pressings are bad: you see the dents ( and during pressing you see the toolings shift)
The welding is so ad randomly
Throwing frames on the floor?!?!?
Grinding on the dirt floor, and all the grid flies everywhere
The manual powder coating gives zero assurance of layer thickness and good surface cover in every corner
On some moments you see the welders not using eye protection
Banging with that steel hammer is proof of irregular toolings. He bangs on surfaces but there is no gauge measuring afterwards.
Imho: i think that all welding can be done in 2 set ups with cheap robots.
The handling of the presses is unnecessary with a magnetic lift.
I wonder how the edge looks after the clipping operation, with worn out clipping tool no sharp cut but bended/ torn surface
Cool. What is the weight of final frame .?
Just to think that whole presentation is for a SINGLE motorcycle brand and specific CC. I cant imagine how much time you need to re tool to a different one😮😮.. 🤔🤔
This is one of the better run factories.
Có bán về Việt Nam ko bạn?
Wuiihh, mbah nya esaf nihh wkwkkw😅
Wkwkwkwk....😂
?
@@agcxd wkwk orag mudeng,mesak eee coookk cooookkk...
🤣🤣🤣
@@Ketuaguild88 :?
That powder painter guy must be crazy with not wearing a mask of any kind.
❤❤❤❤
❤️
Safety? What is it?
Honda beat rangka esaf menangis melihat ini
iy qualitas ok beda AHMPass
3:28 чувак в ластах зачетный😏😏
Уважаемый человек- начальник бригады.
👍👍👍👍💪
Rupanya disinilah rangka esaf Honda dibuat, pantas jadi Honda lipat.
Tidak cat celup, nanti kasusnya sama seperti rabgka esaf di Indonesia hahaha😊
👍👍👍
High performance frames, hardley? What are these frames for 125 cc bikes?
No sir these frames r cd 70 bike
@globalartiisans Honda design form the late 1960s.
CL70 in the US. I have one now, and it still works well. A well engineered motorcycle for the cost. They are reliable transportation still in many countries.
#Кто заметил чювака в ластах?
5:45
😂😂😂😂😂
Cardboard on feet to stop sparks getting into the sandals, but that's the first thing I thought too.
Pressing a couple of sheets at the same time means that the pressed parts are different sizes even marginally.
exellen
What Make and Model of bike is this frame for?
Honda-Kopie 😮😊
70cc
❤
हीरो होंडा cd 100का फ्रेम है ये।
For everyone who knocked them, keep in mind they are a nuclear power
Pelo chassis.é.a.dafra super.100 tive duas! E super 50
Mùa có thể là màu xanh da trời hoặt màu đỏ hay là màu vàng.
At least they use clean new metal
Rangka motor yg kursbg bgs ds tidak kuat mudsh berkarat dan mudah patah
tau darimana?
Esaf 😁
Между прочим это мопеды хонда
Sorry to see a country still stuck in 1900’s
which company os this
what model is this bike?
2024 model
apakah alasan di negara pakistan tidak membuat motor-motor dengan model terbaru?
Chinese Clones of Honda CD70 4-Stroke. Total production in Pakistan 2.5M. Honda makes >1.3M, while Clones make up the rest.
These people use the small resources they have to come up with good products
Hoje as grandes empresas, usam mão de obra praticamente escrava e ainda fica gente batendo palmas pra isso. Quantos trabalhadores são mortos ou terão danos graves sem assistência das empresas. Isso é horrível e não algo para admirar.
To me the build quality and attention to detail seem very poor. Also this rough handling and rushed assembly don't help. That being said I think that the low production cost of these frames is unbeatable
Zero QC
@@truantrayrubbish statement
@@teewizz6089you have no idea why the remark was made because you have no idea about quality control
Meny old model ka frame now model my convert kerwana hy
Sir asy nai ho skhta yeh proper factory ka kam haii
tôi suy nghỉ ra rồi về màu sắt sường xe
Gujranwala my Hy
00:17 wow
Honda C50 frame ???
@@AM9410._- cd70
Those are honda motorcycle frames
Yes
No. These are frames for honda copies. Honda would never use frames of such low production quality.