Listen EVERYONE if you have problems like:- -Bt module not blinking -automatically moving wheels -automatically disconnected have this type of problems then try making a voltage divider circuit by taking TX and RX as terminals...Search it on youtube or I will make video for this soon..
I can't use the app to move the car..everything is well connected, the code is working, the Bluetooth is connected, and that red circle🔴 turned into green 🟢, but i can't move the car why is that ?
hi bhaiya, i made the car and its getting connected and the motors are also rotating when i press forward or any command, but for example- if i press forward button it will work, but sometimes it malfunctions and keeps going forward even if i dont press the button, and no other command works after that, i have to disconnect it and connect it again and again the same problem happens, can u tell me why is it happening and how do i resolve it? pls
@@funshot1234 bhaiya can u please make a video on that and upload on your channel or on your drive and share the link to me? I am new to all this and i dont know how to do this perfectly. pls bhaiya i need your help.....thanks a lot for replying 😃
@@funshot1234 bhaiya can u make a video on the voltage divider circuit how to do it and post it on your youtube channel or make a video and upload in drive and share me the link, i am new to all this stuff, and also can you tell me why this problem occurred only in my hardware? is the arduino uno or motor shield defective? bhaiya pls help, thanks a lot for replying😊
@@sanandiyachirag1120 it need continous 6 volt to 9 volt not less than that and 9Volt battery voltage dorps to less than 6volt when it is in load condition ie when the four motor runs it should have the voltage more than 6volt
This problem generally do not occure, it is due to discolabiration of module and code, solution is big I have to make a video in this, A temporary solution is there, you should not long press the forward button just a click you do ok
Bro it's not working and motor shield is small vibrating how to slove please tomorrow is my competition if I connected and start not running and shield is vibrating please rply
Bro I make the Car use the 300 rpm motors. Bluetooth functionality working properly but the tyres are not moving when i detach it from the cardboard i have used they work properly. but it is not working when i set it on cardboard what should i have to do?
Yes brother, but PLEASE NOTE that pinouts are on 1,2,3,4 ok configure accordingly, and be carefull you are using L298N need 12 Volt power supply, Wrong connection could damage your chip.
Bro i did everything as you sayed my car is connecting successfully working also good but the problem is after connecting only once my car moves then stops and no other command works I have to turn off arduino and restart then again same happens only makes one movement and stops give some solution
@@mauryasurajj Don't worry Brother You done it well, Some bt module do not have voltage regulator so it require a perfect 5V so you need this:-www.amazon.in/Electron-C-Type-Charging-Module-Circuit/dp/B0CQWQ1ZG1/ref=mp_s_a_1_8?crid=2FN12IQTAMYA8&dib=eyJ2IjoiMSJ9.aam-mL5eEHlms6Oc8_afLmcy6Os5FVfpcNqn7z5vcuQs2YMgTzIHKVA5RaG1RMfOLWypIMwDaJVoebPR3y6SlVFN5EO_XEtD3XxQ6rV6FT3CAD9O_Tn6Wg-w0OWDYQMFU62XTi6VJp2owNVEawz3bDqQ9Hk1X0UXsP7CL50qfothjf_o-hQdRvY8Jza2t7rL19thavVwVJConLeBSxA-7Q.11mdeDBFBoMQ5721tT9EvDBjPrIFfjwzctksBk9mkU8&dib_tag=se&keywords=power+bank+circuit&qid=1733059695&sprefix=Power+bank+Circuit%2Caps%2C1484&sr=8-8
@@funshot1234 thank-you And I already have that module, But in my case I connected 12v battery to motor driver shield, still do you think I need to something for voltage. I do have L7805cv MOSFET which can help to regulate 5V Or I should change driver shield with L293N motor driver I have that too🙏🙏🙏
@@mauryasurajj Not a bad Idea Yaaa do that Brother use L293N module code for this is also easy, But be carefull using L293N with 12v can damage your Arduino if you connect 5Vin in Arduino from L293N and 12v Vcc without connecting gnd to module as gnd have to be same for 12V vcc and 5v out from module hope you got it Best of Luck Brother.
guys i got same ther error is un plug all motor and power to motor shelid and blutooth module after upload the code connect the bludooth module connect with application and connect the motor one by one test each time while u connecting the motor
Yes brother, but PLEASE NOTE that pinouts are on 1,2,3,4 ok configure accordingly, and be carefull you are using L298N need 12 Volt power supply, Wrong connection could damage your chip.
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Listen EVERYONE if you have problems like:-
-Bt module not blinking
-automatically moving wheels
-automatically disconnected
have this type of problems then try making a voltage divider circuit by taking TX and RX as terminals...Search it on youtube or I will make video for this soon..
Bhisab zindagi bachali mari , before a robotics competition on Arduino car 🔥
Thanks bro it work without any slightest problem
it completed and working thank you sir
Congrats brother
@zzzbobbyyt8222 plz upload your Problem in you channel, and Let me check....
If i use same battery as you there will be no problem at any point but how can i charge it. Can i use rechargable battery so how much volt battery
Bro you are such good youtuber but very very less subscriber under rated dog. TAKE MY subscribe
I can't use the app to move the car..everything is well connected, the code is working, the Bluetooth is connected, and that red circle🔴 turned into green 🟢, but i can't move the car why is that ?
Arduino ❤
How i check my hc05 have logistics level converter please
Say tomorrow is my science competition please
@@XPLOOD_X4 You don't have to check it already accept logic level from 3.2 to 5.0 from it's bydefault converter that's the reason hc05 is perfect.
@@XPLOOD_X4 BEST OF LUCK DEAR 👍
@@funshot1234 thanks
hi bhaiya, i made the car and its getting connected and the motors are also rotating when i press forward or any command, but for example- if i press forward button it will work, but sometimes it malfunctions and keeps going forward even if i dont press the button, and no other command works after that, i have to disconnect it and connect it again and again the same problem happens, can u tell me why is it happening and how do i resolve it? pls
It easy brother make a voltage divider circuit taking RX and TX as terminals, as voltage should not exceed 3V at TX RX pins..
@@funshot1234 bhaiya can u please make a video on that and upload on your channel or on your drive and share the link to me? I am new to all this and i dont know how to do this perfectly. pls bhaiya i need your help.....thanks a lot for replying 😃
@@funshot1234 bhaiya can u make a video on the voltage divider circuit how to do it and post it on your youtube channel or make a video and upload in drive and share me the link, i am new to all this stuff, and also can you tell me why this problem occurred only in my hardware? is the arduino uno or motor shield defective? bhaiya pls help, thanks a lot for replying😊
Good
Thanks A lot keep Supporting
bro i am using single 9v battery and it's not working how much power supply do this car need?
@@sanandiyachirag1120 it need continous 6 volt to 9 volt not less than that and 9Volt battery voltage dorps to less than 6volt when it is in load condition ie when the four motor runs it should have the voltage more than 6volt
Hi when I am pressing forward button it's running automatically what problem
This problem generally do not occure, it is due to discolabiration of module and code, solution is big I have to make a video in this, A temporary solution is there, you should not long press the forward button just a click you do ok
And do not press two buttons at the same time try this and reply..
Or try to make a voltage divider circuit
Thankyou brother👍👍👍
Bro bluetooth is working but not running car and disconnected connection please say the solution
@@XPLOOD_X4 ok upload video in you channel of your problem by showing all the connection you have done, let me see what's wrong.
@@funshot1234 ok
Can we use normal 3.3v 2 batterys
@@XPLOOD_X4 yes but in series
Bro it's not working and motor shield is small vibrating how to slove please tomorrow is my competition if I connected and start not running and shield is vibrating please rply
How much mah is the battery of?
2000 mah
Cost under 60 -75
Dublicate battary cost 40-55
@@funshot1234 ok thnk u so much ,can u plz also tell me is it 3.7V battery ?
Yes you are right
Hello sir
Canwe use Arduino uno only for this
Yes but controlling four motors will damage your arduino, I have tried and Within 5 sec Arduino Ic got damaged.
So Don't try without Driver Shield ok Thank you
Great work 🔥
Bro I make the Car use the 300 rpm motors.
Bluetooth functionality working properly but the tyres are not moving when i detach it from the cardboard i have used they work properly. but it is not working when i set it on cardboard what should i have to do?
@@BhavikBhimani ok can you upload your problem in your channel, let me see what's wrong..and have you seen the circuit diagram?
Can we use 9v battery ?
Hello bhi jo bluetooth ka rx hai vo Arduino ke rx mai jayega no vo to pin no.0 par hai Arduino mai likha hai
Bhai code file open nahi horaha hai
Bro tomorrow I have competition can you wish all the best??😢
Sir the car is working but after a few minutes it is disconnecting by its own what can be the reason
Low voltage battery
How to recharge the battery please say sir
Ok see this video:- ua-cam.com/video/3TlzJ5NJr-U/v-deo.htmlsi=FEKsIucMUAzSG9YS
@@XPLOOD_X4 or buy a charging module
Can we use 3 2000mh lithium cell
@@Flexo_ff2699 no
Code file not opening bro please help me
Here is the Solution :-ua-cam.com/users/shortsFhszWC6nCPg?si=sbvetYxk4VUHPUSS
Nice I will Try
All the best
Bro isme + voice+ gestures kaise dale
Can i use L298N motordriver
Yes brother, but PLEASE NOTE that pinouts are on 1,2,3,4 ok configure accordingly, and be carefull you are using L298N need 12 Volt power supply, Wrong connection could damage your chip.
👌👌👌
Apload video on Bluetooth connected grass cutter please sir...
You mean an As Usual car with grass cutting facility
If yes then reply yes
Bro i did everything as you sayed my car is connecting successfully working also good but the problem is after connecting only once my car moves then stops and no other command works
I have to turn off arduino and restart then again same happens only makes one movement and stops give some solution
Tell something to solve this
@@mauryasurajj Don't worry Brother You done it well, Some bt module do not have voltage regulator so it require a perfect 5V so you need this:-www.amazon.in/Electron-C-Type-Charging-Module-Circuit/dp/B0CQWQ1ZG1/ref=mp_s_a_1_8?crid=2FN12IQTAMYA8&dib=eyJ2IjoiMSJ9.aam-mL5eEHlms6Oc8_afLmcy6Os5FVfpcNqn7z5vcuQs2YMgTzIHKVA5RaG1RMfOLWypIMwDaJVoebPR3y6SlVFN5EO_XEtD3XxQ6rV6FT3CAD9O_Tn6Wg-w0OWDYQMFU62XTi6VJp2owNVEawz3bDqQ9Hk1X0UXsP7CL50qfothjf_o-hQdRvY8Jza2t7rL19thavVwVJConLeBSxA-7Q.11mdeDBFBoMQ5721tT9EvDBjPrIFfjwzctksBk9mkU8&dib_tag=se&keywords=power+bank+circuit&qid=1733059695&sprefix=Power+bank+Circuit%2Caps%2C1484&sr=8-8
@@mauryasurajj And Give me Time I will make a circuit diagram in which you will be able to Know how to connect it Thank you..❣️❣️
@@funshot1234 thank-you
And I already have that module,
But in my case I connected 12v battery to motor driver shield, still do you think I need to something for voltage.
I do have L7805cv MOSFET which can help to regulate 5V
Or
I should change driver shield with L293N motor driver I have that too🙏🙏🙏
@@mauryasurajj Not a bad Idea Yaaa do that Brother use L293N module code for this is also easy, But be carefull using L293N with 12v can damage your Arduino if you connect 5Vin in Arduino from L293N and 12v Vcc without connecting gnd to module as gnd have to be same for 12V vcc and 5v out from module hope you got it Best of Luck Brother.
Sir code error bata raha hai please solution
Library pehele install karna hai with proper version as per video and tx rx pin should be disconected while uploading the code
Sab thik hey bhai but move nahi horaha kya kare?
Bhai please voice command robot banaker batao
App kas gnd line sold kiya ha
Sir code send kar dijiye open nahi ho raha hai😢
@@iswarchand4379 Just relax and try again if not let me know...
Not working the code😢😢😢😢😢😢
@@SaranyaVenkateshGallery try looking for the uploaded code
How to download code
No preview available showing
Not showing brother
Pls tell brother
@@raghulspace356 Here is the Video Solution ua-cam.com/users/shortsFhszWC6nCPg?si=DqJ9G2PJ_AD5qyUz
I am using Arduinodroid it's ok
Bluetooth se connect hogai lekin Chal nai rahi
Same bro 😢
Same
guys i got same ther error is un plug all motor and power to motor shelid and blutooth module after upload the code connect the bludooth module connect with application and connect the motor one by one test each time while u connecting the motor
Same problem
With the same Code
Yes brother, but PLEASE NOTE that pinouts are on 1,2,3,4 ok configure accordingly, and be carefull you are using L298N need 12 Volt power supply, Wrong connection could damage your chip.
pls be vegan ANIMALS also have lifes Radhe Radhe
Tasty chicken