Dont use a screwdriver to pry it out.. my father did this and bent the shaft. The drill a hole and thread a screw to pull method workwd for me! Thx for the helpful video 🤙
Looks like I bought the exact same kit as you and I just got done replacing mine in my sportsman 500 now I am getting coolant leaking out of my weep hole. Not sure if I got bad seal. I am guessing if it is coolant leaking it is the mechanical seal that is the issue.
If you look at the sparkplug and its wet and its blowing coolant out the tail pipe or white smoke..Head gasket. If its dripping from the weep hole...its the seal.
The shaft and bearing inside housing how do you pull that apart to change shaft and bearing inside housing do I have pull while engine to do that thanks
Dumb question been work one one these for a friend seen it was leaking out the lil hole could this cause an overheating problem? And when I pressure test it , it don’t leak out that hole or anywhere else just happened to notice it was dripping
When you pressure test it you might be pushing in the mechanical water pump. If it leaks out the weep hole its leaking somewhere. Check the oil in the engine. see if there is coolant in the block.
97 scrambler 500 non ho: I can’t really tell if it’s the weep hole that’s leaking or if it’s the outer impeller seal AND I ABSOLUTELY DO NOT WANNA PULL MOTOR just because frame is in way of pump (no white smoke)
I thought you said in your previous vidios that this was the incorrect way of doing this job ? I was getting water in the crankcase as well . I recently did this job by taking off the "plate" behind the flywheel . I think the problem was the inner seal . So far no water in the oil .
It's a bitch!!! One advice I can give is to do it on a day your super relax and plan on spending a few tedious hours. Found it to be easier to break the seal piece by piece and once you only are down to just the metal and no other obstructions to punch out the metal by delivering super light blows with a small sharp flat screw driver and then slide out the middle piece off the shaft. Using a hook catching the back of whats left pull slowly and gently towards you. Once you see the first edge/sealing surface pull away just work around and it comes off. Not easy but doable.
Nice job, did you put anything on the gasket before you mounted the pump housing back on?
do you remember which kit you bought?
Dont use a screwdriver to pry it out.. my father did this and bent the shaft. The drill a hole and thread a screw to pull method workwd for me! Thx for the helpful video 🤙
Don’t pry on shaft and a little heat wouldn’t hurt😮
nice job
Looks like I bought the exact same kit as you and I just got done replacing mine in my sportsman 500 now I am getting coolant leaking out of my weep hole. Not sure if I got bad seal. I am guessing if it is coolant leaking it is the mechanical seal that is the issue.
Yup. Its leaking or the rubber seal behind it.
I have coolant in my crankcase. Others have said pump seal or could it be the head gasket?
If you look at the sparkplug and its wet and its blowing coolant out the tail pipe or white smoke..Head gasket. If its dripping from the weep hole...its the seal.
Thank you.
I hope I didn't need to do this
The shaft and bearing inside housing how do you pull that apart to change shaft and bearing inside housing do I have pull while engine to do that thanks
I haven't had to do that. but I believe it is pressed in. You would have to split the case halves to get to it on a 500.
Dumb question been work one one these for a friend seen it was leaking out the lil hole could this cause an overheating problem? And when I pressure test it , it don’t leak out that hole or anywhere else just happened to notice it was dripping
When you pressure test it you might be pushing in the mechanical water pump. If it leaks out the weep hole its leaking somewhere. Check the oil in the engine. see if there is coolant in the block.
97 scrambler 500 non ho: I can’t really tell if it’s the weep hole that’s leaking or if it’s the outer impeller seal AND I ABSOLUTELY DO NOT WANNA PULL MOTOR just because frame is in way of pump (no white smoke)
Is this a scrambler 400 or 500? Also what kit part number did you use?
Its a Sportsman 500. It will work on a Scrambler 500.
I thought you said in your previous vidios that this was the incorrect way of doing this job ? I was getting water in the crankcase as well . I recently did this job by taking off the "plate" behind the flywheel . I think the problem was the inner seal . So far no water in the oil .
It's not the best way to do it because if you dont get the inner seal in correctly it could leak. My first attempt years ago failed.
Do you know we’re I can get a transmission for a Polaris Sportsman 500 2001. It is not an HO
I have one, But I'm in Wisconsin
I won't ship.
Ok thanks and love the videos
Well ours is impossible to pull out
Did you get it out? I’m having the same problem
It's a bitch!!! One advice I can give is to do it on a day your super relax and plan on spending a few tedious hours. Found it to be easier to break the seal piece by piece and once you only are down to just the metal and no other obstructions to punch out the metal by delivering super light blows with a small sharp flat screw driver and then slide out the middle piece off the shaft. Using a hook catching the back of whats left pull slowly and gently towards you. Once you see the first edge/sealing surface pull away just work around and it comes off. Not easy but doable.
I just did one and its still leaking out of the hole.....lame
Did you replace the rubber seal behind the mechanical seal?
why you didn’t take the time to allow the camera to focus on the seal..?? This whole video is out of focus..
Actually, I'll be honest. I can't see.
Out of focus, and you are in front of camera.... Rubbish!