FENDER STRATOCASTER - How to Setup your Electric Guitar, Step-by-Step
Вставка
- Опубліковано 8 чер 2024
- MusicNomad and Geoff Luttrell team up like no other FENDER STRAT setup video, with easy to follow how-to setup instructions using MusicNomad's Precision Gauges and Tools and the KEEP IT SIMPLE, SETUP (KISS)™ method. To learn more about the setup tool sets used in this video and how to setup your own guitar visit MusicNomad's Setup Hub: www.musicnomadcare.com/How-To...
Since 2001, Geoff Luttrell Master Guitar Tech of SF Guitarworks and Sonoma County Guitarworks sfguitarworks.com/ has setup thousands of guitars and also teaches countless guitar players how to setup their own guitars in his setup workshops. He does an incredible job, like no other, of breaking down each setup task explaining in layman’s terms why your guitar will play and sound better by performing each setup task and then leads you through each step, giving helpful tips and tricks along the way. Using MusicNomad’s Precision Gauges and Tools, the setup process becomes so simple to perform as you will see for yourself. Follow along with your own guitar and you will be amazed that yes you can setup your own electric guitar. Not only is it fun, but a properly setup guitar takes your playing and sound to a whole new level.
Keep in mind, that the steps he goes through in the exact order can be applied to any electric guitar with individually adjustable saddles. If you have a fixed bridge (i.e. Tune-o-matic) commonly found on Gibson guitars there is a slight change in the order you perform switching steps 2 and 3 (doing the string radius followed by the string action on a fixed bridge guitar). We have a video that shows how to setup an electric guitar with fixed bridge also.
Check out MusicNomad's setup hub for lots of how to videos, setup tools and info on the KEEP IT SIMPLE, SETUP (KISS)™.
0:00 Introduction
1:00 Pre-Setup Steps
3:20 Truss Rod
9:35 Action of Strings
15:36 Radius of Strings
20:02 Nut Height
35:23 Intonation
40:07 Pickup Height - Навчання та стиль
You can fast forward to the specific task below:
1:00 Pre-Setup Steps ua-cam.com/video/2QsomaNW_8w/v-deo.html
3:20 Truss Rod ua-cam.com/video/2QsomaNW_8w/v-deo.html
9:35 Action of Strings ua-cam.com/video/2QsomaNW_8w/v-deo.html
15:36 Radius of Strings ua-cam.com/video/2QsomaNW_8w/v-deo.html
20:02 Nut Height ua-cam.com/video/2QsomaNW_8w/v-deo.html
35:23 Intonation ua-cam.com/video/2QsomaNW_8w/v-deo.html
40:07 Pickup Height ua-cam.com/video/2QsomaNW_8w/v-deo.html
Ppkkkklokoolokooookkk
Is it ok if I use a under-string radius guage during the bridge radius step instead of using the over the top method that you use? I know the difference is minimal but the under-string guage is a bit more precise. This has been nagging at me every time I setup a guitar. I use you method and tools except for the way we set the bridge radius.
Just wanted let you know your video brought a smile on my 10 year old son's face. I had bought him a used Squire strat mini to learn on, it was supposedly "professionally" setup. He brought it to me the other day frustrated with it buzzing and just basically unplayable. I had gotten some setup tools for Christmas. Sat down and walked through your video. Handed the guitar back to him and he was totally amazed.
That is awesome! Thanks for all your support
If your son is only 10 and is already complaining about the setup…he’s gonna be an insane player in the future🤯 When I was 10 you’d have to hand me a guitar missing the strings for me to notice something’s wrong with the setup😂
@@juleswinnfield3958 Hahaha! That's funny, Jules!
I was intimidated about trying to set up my own guitars. I have 4 electrics and one acoustic. I have a player strat that really had me frustrated and it was buzzing crazy on the B string. I watched a video and decided I would upgrade and replace the nut with a graph tech nut and string tree. That fixed that problem and then i came across your videos. Having a lot more confidence I decided to go ahead and get the KISS setup tools. I highly recommend this system. The tools are high quality and a lot of thought went into them from a design stand point. I had a set of Fender bridge saddle adjustment allen wrenches that were complete garbage. I got the Nomad tool kit and that solved that problem. I got through the entire setup and what a difference. I can't thank you guys enough. I'm totally confident that I can setup my own guitars now. 5 guitars adds up to a lot of money in setups that will pay for these tools in no time. I'm going to get the nut files and truss wrench set too. I'm impressed with the quality. Thanks for sharing your knowledge and designing a really nice functional set of tools.
Awesome! Thank you for sharing your experience with us.
these are the best tutorials. I used your gauges to set up a pbass. I notice on the Strat you did not talk bout the tremalo springs.
The clearest and most helpful setup instructions/video I've ever seen.
I took Geoff's set up workshop at his home shop in petemula some years ago. This video is awesome in that it clearly hits most of the points he taught that day. He's the real deal, a true pro. Thanks Geoff.
Could you give me an idea of what is a light touch vs a heavy touch ? In the Truss rod adjustment part ?
the best set up vid ive seen, i just got a guitar and have been browsing these types of vids and i havent found one nearly as detailed as this one, normally, they will say "well, now youll do this and that" but they wont explain or show what this and that is... thank you, just purchased this kit
I just bought a new American Stratocaster Pro II after watching this video 3 times I ordered all the tools including the Nut files.Thanks for the great video.
The most helpful, informative and complete instructions I’ve seen. Thank you!
I set up my Strat following the steps in this video. Has never played better, excellent step by step process.
This guy makes some cool tools and gives great lessons. I have learned a lot from him and applied this to my own guitar setups.
Excellent video and really well explained for us aspiring luthiers that want to know their instruments better! Many thank yous to you friend 🙌🏽🙏🏽
Easily the best video I’ve ever seen about setting up a strat. Thank you.
Got Setup for Xmas and I'm thrilled. This was the first setup I've done that I felt like it was easy and that I didn't second guess that I was doing it right.
Thanks for this video, tried other videos but they weren't very detailed. Just bought a 6 piece set of the tools you used in the video. Thanks for your time and knowledge
Thank you so much ! That's by far the best video on this topic I've ever seen.
Awesome!
Really excellent video tutorial. I'm using the video with my MusicNomad equipment care package and it's a dream. The care pack is really well thought through as well. Well done!
Thanks a lot for this very precise and well explained video. I just bought the basic kit from amazon and was able to adjust my taylor guitar. I owe you one!!
This presentation is absolutely the easiest to understand of any of the tutorial setup videos I have watched. Given the care that went into this tutorial, I will be purchasing the Music Nomad luthier tools to add to my arsenal of guitar maintenance tools. Great work, and thanks a million!👍✌️🙂
No
No What?
Truly enjoyed the step by step video and explanations. Can't wait to purchase your tools and get my stratocaster set up properly.
Thank You. :)
Excellent video!! I set up one of my Strats this weekend by following your video & it worked perfectly! I've tried setups before, but could never get them quite right. Thanks for putting this together for us.
Awesome! Share the video with your Strat community if the occasion arises so more people can learn now to setup their Strat to play and sound great!
I've been using these Music Nomad tools and the KISS process on all my guitars for a few years now. One thing I failed to do early on was fret the first fret when setting the action. Once I added that to the process I started flying through my setups. I personally find the most common suggested measurements on the guage to be perfect for me. No additional adjustment needed. But even if you personally don't like any of the suggested measurements it's still a great way to at the very least get the guitar setup correctly and close enough to your liking that only minimal further adjustment is needed. The best part is their products aren't overly expensive. Step aside StewMac... there's a new dog in the yard.
Best tutorial and explanation on the internet to date.
This was phenomenal. I love the Music Nomad stuff. I have about 9 of their items.
I bought all your set up products and my guitar never sounded so good. I really appreciate the video. Please keep on making stuff like this 🙏
Love hearing this!!
Thanks for such a well-explained tutorial. I'm looking forward to buying a kit from you guys and trying it out on my own Strat. UPDATE: My setup kit and cradle cube arrived, and I'm setting up my strat now. Thanks again.
oh god, dear god do i love guitars, i came to this video once like 3 months ago when i was new to setting up guitars and stuff, and i thought i set it up perfect, yesterday i noticed that i think the setup is kinda bad cause im noticing some buzz on some strings sometimes, so i come back, i re do the string action with the right tools, making sure the radios of the strings is all correct, intonate it again, and im in love with my guitar again.. Thank You
Great advice and nicely explained. Thanks a lot from Germany. :-)
Thanks so much a well explained tutorial I don't know how I missed this video for the last year's This is nothing but a pure solid Gold What I wanna do right now is to buy the setup kit and the nut files. I hope that you guys keep making this kind of videos For beginners like us. Congratulation, guys, you are amazing.
GREAT LEARNING FOR BEGINNER JUST GETTING STARTED THANK YOU
thank you for this lucid explanation. very helpful and instructive. love xxx
Fantastic video. I bought myself the music nomad nut files and the nut height gauge here in New Zealand.
Thank you man. It helps me a lot. Salute 👍
This is a godsend! Please, don't ever take this video down. Subscribed/Bell
Great video thank you. I purchased the files and the radius gauge (from NM)
and will attempt my first ever set up, can't wait.
excellent tutorial 👏 thank you
This was extremely helpful.
Great work Geoff!
Now That is A Strat! Thank You !
Exactly what I’ve been wanting to find
This video made my day...
Great guide. Thanks.
Very good setup video.
Absolutely thankful. Best setup video I have seen so far. A keeper in my "guitar library". Thank you, guys. The tools are a little bit high, at least to me. Any discount or code you can share?
Thanks Geoff, that was super helpful... I tweaked everything, but the nut height, as I don't have the proper file for that currently. My Strat plays and sounds better...thx again!
Nice setup video, but the whole reason a Strat is a Strat is the tremolo and there is no mention on how to set it up.
Take it off.
Done.
After watching the Clapton ‘Crossroad videos’ I’ve noticed that 99% of those players either don’t have the tremolo on their guitar or they just don’t use it. I’ve hard tailed mine, so the whammy bar is lost in the case somewhere.
This was a SUPER great detailed video, very well explained. But I would have made another video for the sales pitch of the tools.
I enjoyed watching the acoustic setup video and now this one. You sold me already (these are great long form commercials!)
I just bought an inexpensive Yamaha FS800 and when I opened it yesterday, I found the action too high right out of the box. I took a chance and sanded 1 mm off the bottom of the saddle (my first attempt) and that improved the action quite a bit. But the action at the 1st fret, especially on the low E is still too high, and I might have the neck a little too straight after tightening the truss rod 1/8 of a turn. So I just ordered the Music Nomad Setup Kit, six individual Music Nomad nut files, the Music Nomad table mat and neck support block, and TUSQ replacement nut and saddle from Graph Tech.
The tools alone cost almost as much as I paid for the guitar! Oh well, I am excited to learn the skills and to have the tools so I can work on my own instruments. Of course, this means I'll need more nut files for my electric guitars which use different string gages! And after I get the action set right on the new Yamaha FS800, I might end up with some buzzing frets and have to buy more tools to level, crown, and polish frets. Oh boy, what did I get myself into?
well guys.....Thanks much for an absolutely great vid and you do a way better job than other sites.....Will invest in your tools as well..................
Thanks for the feedback - we're glad you like the videos!
great video!
Mike McCready showing you how to setuo a guitar 😉 Great video 😊
Awesome
Great Video! Can you please do a full set-up of a Prs? I am purchasing your PRS feeler gauge and would also love to find out how to adjust string action height on one of their bridges as well
We are working it. Stay tuned and subscribe to our channel so you can be alerted as we launch new videos
@@MusicNomadCare Awesome Thanks! I'm actually a subscriber already and own a lot of your products. You guys are great!
Great Tutorial!! I just received my set and I will work on my guitars. Just a little question, if my guitar has a compound radius 8 to 12. Should I use the 12 radius gauge?
Yes, you use the largest number on a compound radius fretboard, which is the radius at the last fret.
Awesome vid, one of the best (maybe the best) out there that I have found thus far coupled with excellent tools.
When you are checking your 'action' on the 12th fret, do you look to actually see the desired line on the tool OR so the line is just NOT visible?
Thanks! The bottom of the string should meet the top of the line and be visible. This makes it easier to see and how our string action works. We are not sure about other string action gauges.
Hey, thanks a lot! This is an excellent video! I know that there are lots of people asking for the tremolo setup, any news on that? Let's imagine that I know how to setup the tremolo, at what point should I do it? Like the first thing, or the last one, or in the middle before setting pickups high? Thanks again!!
Thanks for watching our how to videos, we spend a lot of time making them to help our community. Check out this video we did on how to set up a floyd rose step-by-step: ua-cam.com/video/lS2YwAilgu0/v-deo.html
Thanks for the video! Do you firmly recommend following the steps in this specific order? Any of you folks in comments do it in a different order?
Yes you need to perform the full setup in the proper KISS flow because its a linear process and all the steps are using a fixed reference point at the 1st fret so if your nut height slots are incorrect it doesnt change the other measurements and adjustments you made in the previous steps so you will not need to go back and remeasure and adjust
I've been playing 10s on my strat forever as strictly a rhythm player. Thinking of changing to 9s to start doing some lead work and make the bends a bit easier. Would I need to have a new setup going from 10s to 9s? Thanks. I love these videos.
There should be no issue as long as your string gauge is no higher or lower than 3-4 thousand of an inch of the nut slot size which it shouldn't be going from 9s to 10s but you can always use our precision setup gauge set to check to see if you need a setup
HI, thanks for the great video and product. One question, can I use a regular capo on the first fret instead of your pick capo? I bought your action gauge but I lost the pick capo. Thanks
The pick capo allows you to hold the string down on top of the 1st fret with just enough tension and is easy to slip in without worrying about where it sits on the fret and how much tension is on it. Yes, you can use a regular capo but you need to make sure it is holding down the string directly on top of the 1st fret using the least amount of tension. You will have an inaccurate string height if the capo is too far forward on the fret.
Great video! Once this process is complete should the strings on an electric guitar buzz when played acoustically?
There should be no buzzing. The KISS setup method is based on doing all the steps in order and having level frets.
For worn or un-even frets you will have to compensate for that until you are able to get fretwork done. To achieve clean notes and no buzzing without fretwork, you will need to raise the action until you achieve no buzz. More relief in the neck and higher string action can solve this but is harder to play and can lead to intonation issues. Another cause for buzzing can be that your nut slots are too low or were cut too low. If you are having any of these issues, we recommend you take your guitar to a qualified repair shop.
I have bought many of your tools and they are top notch! Best on the market. I have a question about intonation if you don’t mind. When I’m done with intonation saddles don’t always follow the typical shape. ( bass string saddles further from nut and Treble string saddles closer to the nut). My guitar always plays well anyway. Should I care? Thanks ;)
It is normal where your strings are positioned on the saddle.
You have a really nice set of videos. This one is great! However, I would have loved a mic'd amp audio example of a clean string sound experiencing worrble from being too close to the pickups.
How about neck angle ( shim or not )
7:24 your headstock went into another dimension 😨
great video! i have a 62 reissue, so couldn’t ask for a more perfect setup vid! quick question. fender specs and guitar setup guys like dan erlewine and gerry haze capo at 1st like you, but when measure action and relief while pressing down at the 17th fret, not the 12th like you. what is your rational for that? i know others do as well. thanks again!
We're glad this video helped you out with your 62 reissue! We respect the different ways manufacturers and repair techs approach neck relief. With Master Guitar Tech Geoff Luttrell along with other top repair techs we developed our KISS method using the 1st and 12th fret and measuring at the 6th fret to accommodate most all guitars using a common measurement. The relief of the neck at the 6th fret is in the middle of the span between the 1st and 12th fret.
So, and this is just to be clear since I did not hear it mentioned in the video, if you set the electric guitar to these recommended settings and you then get fret buzz, the solutions would be 1) raise the action a bit higher at the saddle, or 2) try to determine where the fret is buzzing and address that with either your luthier or, if you have the skills, crown or shave those specific "high" fret areas? Hope that makes sense. Thanks. Great video.
The KISS setup method is based on doing all the steps in order and having level frets. For example, if you do the String Action Height adjustment only and you have fret buzz, it may be because you did not adjust your Truss Rod. Make sure you follow all the steps in the setup process.
For worn or un-even frets you will have to compensate for that until you are able to get fretwork done. To achieve clean notes and no buzzing without fretwork, you will need to raise the action until you achieve no buzz. More relief in the neck and higher string action can solve this but is harder to play and can lead to intonation issues. Another cause for buzzing can be that your nut slots are too low or were cut too low. If you are having any of these issues, we recommend you take your guitar to a qualified repair shop.
Do these measurements translate to lower tuned guitars (G, A, etc.) as well with a 7 or 8 strings? Is there a way to figure out the rough measurements needed for those types of situations?
Our measurements we provide are the most common measurements for 6 string guitars that are tuned to standard pitch.
Is it possible that pickup height causes 1st string to choke a bit when bending north from 12th fret? Amazing tutorial by the way, one of the best I have seen!
It could be a possibility. Can you reach out to tech@musicnomad.com, and we can help you with your specific instrument needs. Thanks!
@@MusicNomadCare Thanks! Another quick question - I have just filed my nut slots, and the strings are quite deep now. Does this affect the sound in any way? I can't really tell, I see there are all kinds of string "depths", so perhaps it is just a visual preference?
How do you set the string height/saddle height, when working on a neck with compound radius?
Use the largest number / flattest part of the compound radius to work with. If you have any further questions, please reach out to tech@musicnomad.com
I've had the musicnomad string action gauge for a few years and absolutely love it. It will probably last me a lifetime and is easy to use. I also have all guitar surface cleaning products. I don't have any other set up tools from musicnomad, and I want to follow this guide. It's a little bit tricky to follow along with different tools, for example, when measuring the nut height. Because the musicnomad nut height gauge doesn't show us any quantitative units of measurement, I have no idea how to use something else. I think it's cool that musicnomad keeps it simple by telling the user "yes, this is fine" or "not fine, file the nut". But I have no idea what I am supposed to aim for when using a tool that does actually show the quantity that is being measured. I figured the easiest solution is just to buy all of the music nomad tools. But now I'm a little irritated to see that you sell all of these gauges separately. For example, why not just sell one set of feeler gauges that includes what we need for truss rod relief and nut height? I'd rather have a more compact set of tools, and I bet the price would be lower if these were both a part of a single set. Instead, there are 6 different pieces that are needed for the complete set of guages, and it comes out to a whopping 60 bucks. I have seen complete sets of feeler gauges for like $10 before. Granted, they are not as easy to use and are not as conveniently labeled, but I don't think I can justify paying that much just for convenience.
Only $60.00 ?
Pedro, it sounds like you need to do more overtime at McDonald's.
We need to put capo on 1st fret for adjusting string action (string height) ?
I was not aware of this.
I never put capo for setting up action. So the action on my guitar was 2.5mm at 12th fret, both on low e and high E strings without any capo.
Didn't like that action but anything lower than that, I get fret buzz on all of my guitars.
In the flow, string height comes before nut height. The measurements we have are based on using the pick capo at the first fret. Since the nut has not been addressed yet, you would be using a height reference point that could be off. The first fret is a fixed height to adjust from. After going through the KISS method and using the most common measurements, if you get fret buzz then you may have uneven fret or some type of fret issues and may want to get it looked at.
When checking string action, is it industry standard to fret the 1st fret prior to measuring? If you leave the 1st fret open measurements can differ dramatically.
Holding down the string at the first fret with the Pick Capo allows you to make an accurate adjustment following the KISS methods linear flow. In the flow you have not yet addressed your nut slot height which makes it a nonvalid reference point. Adjusting the nut slot height is the last step in the playability part of the setup. Following the KISS linear flow allows you to setup your guitar to play and sound great without having to go back and repeat steps.
I learned a lot on this vedio. Great tutorial lot of theory and experience thanks..
Question: Your Intonation Setup is the first I've ever seen using the 12th and 17th Fret. I've been used to the 12th Fret Harmonic/Fretted Note or the measure of the octaves. Could you please elaborate on the rationale of the 12th and 17th Method? Thanks for any help!
measuring at the 12th & 17th fret is making sure you're properly intonated through out neck.
Excellent video but a question for you. Around 11:24 you are speaking in terms of inches (1.50 and 1.25). Did you switch to millimeters at 11:32? 1.50 inches equates to .060 and 1.25 equates to .050 correct? Thanks very much.
You have it slightly backwards, the 1.50 is a measurement in millimeters which converts to 0.060 thousands of an inch.
its confused me mate because if u measure with capo on first fret 60 thou and 50 thou when u take capo off its 2mm and 175mm
Fender recommends 10/ 1000 in. For truss rod string height
I purchased the tools you recommended. I followed your instructions including the Low-Med action. My American Standard Strat (circa 2014) turned out fine. My 1979 Strat didn't. The action is such that I get buzzing on the low E and fret out when I bend a note a whole step on the high E above the 12th fret. Any ideas why?
Sounds like you may need some fret work on your vintage guitar. For worn or un-even frets you will have to compensate for that until you are able to get fretwork done. To achieve clean notes and no buzzing without fretwork, you will need to raise the action until you achieve no buzz. More relief in the neck and higher string action can solve this but is harder to play and can lead to intonation issues. Another cause for buzzing can be that your nut slots are too low or were cut too low. If you are having any of these issues, we recommend you take your guitar to a qualified repair shop.
So what curve profile should you adjust the action on the bridge to when you have a compound curve on your neck. e.g. on a fender American Ultra?
With your strings off, you will still measure the fretboard radius at the last fret. You will then match your string radius to the fretboard radius. For example if you have a 9.5" to 12" compound radius you will want to use the larger number which is the flattest part of the radius.
@@MusicNomadCare thanks very much. I’m on it. 😎
Once you've filed the nut slots, would the top of the nut also need to be filed down/reshaped? The strings would sit deeper and ideally the strings should protrude out of the top of the nut slightly
The procedure for this would be to take off material on the bottom of the nut then set the nut slots to the proper height so the strings sit above the nut about 1/4”
How about a setting up a Fender Precision / Jazz Bass video?
Eric, it will happen but a few months out. Hope to have a lot more brands dropping throughout 2021. A lot goes into each video so we are excited about more for our community.
How about the trem?
after i measured the action and set it right for my strat i started to get buzz when i fret anything above 12th fret so i rechecked my truss rod but everyting seems fine how do i get rid of buzz? i got a compund radius fret board (7-1/4 first fret and 9-1/2 on 12th fret) would i use the 9.5" side?
The KISS setup method is based on doing all the steps in order and having level frets. After going through the entire flow in the proper order and still getting buzz you may have worn or un-even frets and will have to compensate for that until you are able to get fretwork done. To achieve clean notes and no buzzing without fretwork, you will need to raise the action until you achieve no buzz. More relief in the neck and higher string action can solve this but is harder to play and can lead to intonation issues. Another cause for buzzing can be that your nut slots are too low or were cut too low. If you are having any of these issues, we recommend you take your guitar to a qualified repair shop.
For the neck relief, shouldn't you use a notched straightedge?
the KISS method is designed to pick capo at the 1st fret, press down on the 12th fret and use the feeler gauge at the 6th fret to determine your relief.
So what if I have a player series ssh.. strat will this work
Yes it will work great
When you the Nut files set will be available?
We are starting to ship our pre order this week.
Great job but I still have an issue intonating the high E-string.
I have an American Strat. It has two bolts / screws in front securing the bridge.
My strobe shows the high E string slightly flat and I cannot shorten the string anymore because the saddle mechanism is right up against the bridge bolt. Neck relief and string height are set to spec.
Do you have a solution?
Thanks.
It sounds like your spring is not allowing your saddle to move back far enough. Our guitar tech can help determine the solution, shoot him an email at tech@musicnomad.com and he will help you out.
I tend to have a problem when restringing a guitar with a floating tremolo system where the floating trem will lift and be angled downward toward the pickups rather than parallel to the body. How do I correct this?
It sounds like you may need to tighten your springs, for more info on how to do this and your scenario email our guitar th at tech@musicnomad.com
I have acompound radius neck on my strat ultra. 10"-14". What should I use for setting action on A,D,G, and B strings? Thanks
match the measurement at your last fret
Our method is designed to match the radius of the last fret with the bridge. These measurements are the most commonly used. For more information on how to use the gauges, email us at tech@musicnomad.com
Want to save a couple hundred bucks per guitar? This video is an easy-to-understand guild to doing your own neck setup, which is what I do to every one of my instruments.
How do we set radius for a compound radius neck.
For example my Charvel pro mod has 12-16” radius.
Do I set the strings to the 16” radius?
With your strings off, you will still measure the fretboard radius at the last fret. You will then match your string radius to the fretboard radius. For example, if you have a 9.5" to 12" compound radius, you will want to use the larger number, which is the flattest part of the radius.
@@MusicNomadCare thanks so much ! This is the best explanation I’ve heard or seen anywhere.
I don’t regret buying several music nomad products !
Thanks so much for responding !
question: I have a 62 strat and when I lower the high e string to 50/1000s it tends to choke out when I bend. How do I fix this?
Hi, Your guitar may need fret work. You can try raising the action until you can get the frets evaluated. Feel free to reach out to tech@musicnomad.com for additional help.
I have one silly question, why no 9 gauge nut file? I'm looking to buy the full set, but there are a lot of people who use 9 - 42 and 9 - 46 strings, so one would think that it would be at least available.
The general rule is that the file should be the same size as the string, up to no more than .003" - .004" larger than the string. If you go much larger, the slot can become so large that the string vibrates in the slot, causing a buzz. If you use a file smaller than the string, the slot will be too tight, causing tuning issues.
Is it ok if I use a under-string radius guage during the bridge radius step instead of using the over the top method that you use? I know the difference is minimal but the under-string guage is a bit more precise. This has been nagging at me every time I setup a guitar. I use you method and tools except for the way we set the bridge radius.
That's fine. The under string is a bit more accurate, as it is measuring the part of the string that touches the fret. Many people have trouble seeing it, so the over string gauge is more than accurate enough. The difference is just a few thousandths. Thanks for watching! Geoff
if i measure 60 thou low and 50 thou high with capo on first fret when i take the plectrum off it measures at 2mm low and 175mm high please help????
Reach out to our tech, he will be be able to troubleshoot and walk you through any questions and the process. email him at tech@musicnomad.com
I am a bit confused here. Capo on 1st fret and pressed on the 12th fret? Last fret? Or where the neck meets the body?
You capo at the first fret using the pick capo and press down on the top of the 12th fret or at the 13th fret so the string terminates on the 12th fret and then measure at the 6th fret. Feel free to email us at tech@musicnomad.com to discuss your specific instrument needs. Thanks!
Is it necessary to loosen the strings prior to the truss rod adjustment? Thank you.
No you want to have your guitar in tune to measure and adjust your truss rod
Got it, thank you!!
If I have 56 gauge will there be one for that gauge in the nut file set?
With a .056 low E our Acoustic Set MN670 has a .056 and the rest of the sizes may accommodate your string set. We also sell the .056 MN661 as a single file that you can add to the Electric Light Set MN668. Email tech@musicnomad.com for more information.
great video but missing one crucial element on the strat setup which is the floating bridge . setting this up has an impact on all the rest of the setup as well
For further info on the trem bridge on your fender strat reach out to our guitar tech at tech@musicnomad.com
okay but why don’t you add this in your stratocaster set up video ? it’s a major part of it .
You're correct but we do have plans on launching more videos and addressing that type of tremolo. For the time being check out our setup video on how to setup a guitar with a Floyd Rose system. There are some similarities in the setup process that may help you with the tremolo setup on your strat. ua-cam.com/video/lS2YwAilgu0/v-deo.html
Ok - I adjusted the truss rod and did everything all the way down to intonation. The first few frets on a few strings are pretty sharp. What could this be?
It sounds like you may have slightly high nut slots. We recommend to go back and measure your nut heights and see if you need to make any adjustments. if your nut slots are slightly high it can cause sharp notes. You can always email our guitar tech at Tech@musicnomad.com for more questions and clarification
Does this work for fender squires?
Yes the process is the same but the truss rod adjustment is slightly different since on a squire the truss rod is located at the headstock and Geoff addresses this in the video during Step 1.
My strat is a no radius neck it’s a us ultra and it’s flat across the fret board would I need a radius gauge ?
If your fretboard is truly flat you will not need a radius gauge.
@@MusicNomadCare hey thanks and thanks for the video, matter fact I’m ordering your product as I type , awesome easy step by step