Nice man I'm definitely going to do this mod it will help the GDI engine with carbon build up every precaution matters. Plugs oil clean air PVC valve catch can will help make your engine last.
Mine is about 16 inches away from the intake and I used the OEM hose, just bought 1 hose for the PCV to inlet. I didn’t disconnect the one to the manifold because it looked out of reach.
Aguyfromdubjay I installed an L bracket under the passenger side of the strut bar, on top of the bolt pinning down the ground ribbon cable. If you do this, be sure to sit it as snug as possible, or you get loud rattling between your strut bar and the metal of the can.
Nice DIY! Just curious to see if you've read anything about removing the line going from the valve cover to the intake? I've read on the forums that it's a good idea to remove it, put a breather filter on it and tuck it under the engine. Or use another OCC.
Jeffrey Dale This oil catch can i used on the other line. And it didnt pick up any oil at all. So i stuck it on this one where alot of people say they catch alot of oil. Thank you for the compliment also. Much appreciated.
wouldnt you want the catch can inlet lower the the hose coming off the engine so gravity will assist in puling the oil to the can? Otherwise wont it just run back into the engine?
installed same way,,,except added a check valve in line going into intake...approx 700 miles later emptied 4ounces of tan fuel soaked oil outta catch can...?wth? is this normal?please help.
Dustyaman, I installed my catch following this as the guide. Same parts, 3/8 fuel line, plastic 3/8 to 3/8 vaccum connector, fed under the cover. Do you notice an extra ticking noise coming from the vaccum connector you installed for the out line?
So i installed it the way your video shows. Everything is tight etc...The can catches a light brown fuel/oil mix but also i get fumes inside tge cabin of the car. Do you experience that?
+Michael Charles - Use the same size as your Car / Trucks. Don't go under 1/2" if you are running long hose..... Also, LESS / SHORT hoses... The better!!!
Unfortunately the ADD W1 are really terrible catch cans. They don't have any sort of proper baffling, and won't filter too much. You could use stainless steel mesh, but that wouldn't be as good as the other options.
Lazaro Roman In testing the W2 allows more oil through than other cans. Just because it's doing something doesn't mean it's doing everything it should.
lol i got the same car, color, and catch can. Do you have a tune yet? I got a the 91 octane tune from btr and it really wakes it up. Also i put my occ under the cai where the stock airbox was to save all the tubing.
TheDustyaman tork has blown up like 23 motors so far. idk if you live near Illinois but i would recommend btr for a custom tune in there shop or ordering a seperate ecu. when i ordered mine it was an 8 week nightmare. I gave them my ecu to work on as a comparison because the one they sent me wouldnt start the car. when they finally sent it back they just tuned my ecu and not the stealthy replacement. which honestly is fucking bullshit. but the tune is not a bad deal. If there is a place near you that tunes hyundais though i would just tune there. Oh and are you getting an odd idle with the can?
Adam Gottschalk www.ebay.com/itm/like/201600784538?lpid=82&chn=ps&ul_ref=http%253A%252F%252Frover.ebay.com%252Frover%252F1%252F711-117182-37290-0%252F2%253Fmtid%253D1588%2526kwid%253D1%2526crlp%253D53601919689_324272%2526itemid%253D201600784538%2526targetid%253D186360209049%2526rpc%253D0.33%2526rpc_upld_id%253D83599%2526device%253Dm%2526mpre%253Dhttp%25253A%25252F%25252Fwww.ebay.com%25252Fulk%25252Fitm%25252Flike%25252F201600784538%25253Flpid%25253D82%252526chn%25253Dps%2526adtype%253Dpla%2526googleloc%253D9025754%2526poi%253D9025755%2526campaignid%253D239125209%2526adgroupid%253D14978428809%2526rlsatarget%253Dpla-186360209049%2526gclid%253DCjwKEAjws5zABRDqkoOniLqfywESJACjdoiGZajN3zGsGaSqkDfrX5R4FAfvi6bPcF4Y0AeFxZ72HhoCJwnw_wcB%2526srcrot%253D711-117182-37290-0%2526rvr_id%253D1111809638243&ul_noapp=true
best routing demonstration ive seen ,, thank you sir...
Your explanations are spot on , no fillers like everyone else talking other shit over talking.. thank you
the one I try to get to the point in my videos. Some guys put 15 minutes of vlogging before the even start on something. I think that’s pointless.
THank you for taking the time to make this, I just ordered my oil catch following your instruction.
Thank you for this, I'm installing mine tomorrow and I finally understand what hoses go where with an aftermarket intake.
thank you. your install was the best I've seen on this subject for a veloster turbo.
Jason Givens Thank you much appreciated!!
Nice man I'm definitely going to do this mod it will help the GDI engine with carbon build up every precaution matters. Plugs oil clean air PVC valve catch can will help make your engine last.
just did it!
just installed mine today!!! goodluck with the rest of your project!
emanuel emanuel Thank you kind sir
Mine is about 16 inches away from the intake and I used the OEM hose, just bought 1 hose for the PCV to inlet. I didn’t disconnect the one to the manifold because it looked out of reach.
Salut! Adaugă-mă pe Facebook te rog, să îmi arăți și mie cum se procedează. Vlad Alexandru Petrescu 😁
Thanks man this helped a lot and added my catch can the same as you.
alex andrade very cool. Glad to help
I hope my catch can that I ordered fits there with a strut bar as well. Didn't even think about it until I watched you put yours there
Aguyfromdubjay you can always make it work. 😁
Aguyfromdubjay I installed an L bracket under the passenger side of the strut bar, on top of the bolt pinning down the ground ribbon cable. If you do this, be sure to sit it as snug as possible, or you get loud rattling between your strut bar and the metal of the can.
BallestraToad sorry for the super late reply, but I got it! Thank you!
put on a provent 200 catch can , they are filted to one micron and have pressure re-leaf values on them,there the best.
Hello, my friend, I liked the project, I'm from Brazil and I wanted to know how many millimeters is the hose used? Thank you and congratulations.
Edinho Oliveira 15mm and thank you for the kind comments
Should have started the car we wanted to hear how old is going to sound and even if it was going to work
Good video brotha 👍🏼
Thank you man!!!
I’m wondering what’s that strap thing that’s attached to the coilover. Is that a ground for something?
Nice DIY! Just curious to see if you've read anything about removing the line going from the valve cover to the intake? I've read on the forums that it's a good idea to remove it, put a breather filter on it and tuck it under the engine. Or use another OCC.
Jeffrey Dale This oil catch can i used on the other line. And it didnt pick up any oil at all. So i stuck it on this one where alot of people say they catch alot of oil. Thank you for the compliment also. Much appreciated.
Great video! Are the fittings on the can 10mm?
wouldnt you want the catch can inlet lower the the hose coming off the engine so gravity will assist in puling the oil to the can? Otherwise wont it just run back into the engine?
Hopefully you've learned about pressure since writing this comment
I know this is an old video but did it catch a lot of oil? Some people say there's hasn't caught any.
installed same way,,,except added a check valve in line going into intake...approx 700 miles later emptied 4ounces of tan fuel soaked oil outta catch can...?wth? is this normal?please help.
So did you change the vacuum connector I personally am using the same one because the copper one gets stuck almost impossible to get it off again ????
Dustyaman, I installed my catch following this as the guide. Same parts, 3/8 fuel line, plastic 3/8 to 3/8 vaccum connector, fed under the cover. Do you notice an extra ticking noise coming from the vaccum connector you installed for the out line?
ljz1988 your just hearing the gdi injection. It's fine
So i installed it the way your video shows. Everything is tight etc...The can catches a light brown fuel/oil mix but also i get fumes inside tge cabin of the car. Do you experience that?
K C I have not.
What size hose?
three eighths
What size hose and connector did u use ?
+Michael Charles - Use the same size as your Car / Trucks. Don't go under 1/2" if you are running long hose..... Also, LESS / SHORT hoses... The better!!!
You should be using a check valve!
Unfortunately the ADD W1 are really terrible catch cans. They don't have any sort of proper baffling, and won't filter too much. You could use stainless steel mesh, but that wouldn't be as good as the other options.
Nathan Amons I have had no issues with mine.
Lazaro Roman What do you qualify as issues? Lol. No baffling, high condensation content, no seals. Bad can.
Nathan Amons my catch can baffle just fine it does the job it's suppose to do. idk what your expecting!
Lazaro Roman In testing the W2 allows more oil through than other cans. Just because it's doing something doesn't mean it's doing everything it should.
do u remember what drill bit u use to drill to the side of that strut tower?
Lazaro Roman 1/8 bit then a self tapping screw
Just installed this on 2013 Veloster non turbo. You will need 5 ft of 3/8 and 5 ft 0f 7/16
After installing my occ this way, it threw a code.
Says Idle Air Control System RPM Higher Than Expected.
db That’s weird I never got a code. And all my veloster buds never did either. There has to be something else going on in your car.
@@TheDustyaman i have an occ with a breather. Veloster Turbo Forum said most likely its my breather.
Does any of ur VT buds use an occ w/ breather?
@@dbrzy8989 no. The breather breaks the vacuum.
Dusty does this void warranty? I can't find any posts that confirm or deny it.
Aguyfromdubjay No it wont. It only helps the motor.
Aguyfromdubjay any modifications will void the warranty
I should get me one of those. Mine has 12k miles on it
Never to late for one man.
TheDustyaman you don't use a small scourer in the catch can to capture oil particles?
The top of it has a specific type of baffles inside so no need forr any type of mesh. you would be amazed on how much it catches.
This is a 80 dollar catch can. very well made
Well I'm looking at a $20 occ instead lol!
Why not just vent to atmosphere? Catch Cans don’t do as good a job as they say tbh
lol i got the same car, color, and catch can. Do you have a tune yet? I got a the 91 octane tune from btr and it really wakes it up. Also i put my occ under the cai where the stock airbox was to save all the tubing.
blakekrocks do you have the dct
TheDustyaman nope 6-speed
Ah ok. I'm trying to decide the best tuner for the dct. I've heard nightmare stories about tork tuning
TheDustyaman tork has blown up like 23 motors so far. idk if you live near Illinois but i would recommend btr for a custom tune in there shop or ordering a seperate ecu. when i ordered mine it was an 8 week nightmare. I gave them my ecu to work on as a comparison because the one they sent me wouldnt start the car. when they finally sent it back they just tuned my ecu and not the stealthy replacement. which honestly is fucking bullshit. but the tune is not a bad deal. If there is a place near you that tunes hyundais though i would just tune there. Oh and are you getting an odd idle with the can?
blakekrocks yeah in the mornings I get a pretty nasty idle. But it doesn't do it on every start up. So was that tork that took 8 weeks or btr?
5ft of hose enough or did you use more?
OreShqipe get 10 feet
Thanks, good lookin out
Any updates?
stephen trinidad the car has been gone for a couple years now
dat dere oil catch can- extra 300 hp brah😂🤣
Ruvinskikauski Amourelius u dumb!
ulises santoyo easy there bud it's youchoob. stickers add more torque 1lb per letter and 1.5lb if it's CAPS yo
Do you have a link to the oil catch can you use?
Adam Gottschalk www.ebay.com/itm/like/201600784538?lpid=82&chn=ps&ul_ref=http%253A%252F%252Frover.ebay.com%252Frover%252F1%252F711-117182-37290-0%252F2%253Fmtid%253D1588%2526kwid%253D1%2526crlp%253D53601919689_324272%2526itemid%253D201600784538%2526targetid%253D186360209049%2526rpc%253D0.33%2526rpc_upld_id%253D83599%2526device%253Dm%2526mpre%253Dhttp%25253A%25252F%25252Fwww.ebay.com%25252Fulk%25252Fitm%25252Flike%25252F201600784538%25253Flpid%25253D82%252526chn%25253Dps%2526adtype%253Dpla%2526googleloc%253D9025754%2526poi%253D9025755%2526campaignid%253D239125209%2526adgroupid%253D14978428809%2526rlsatarget%253Dpla-186360209049%2526gclid%253DCjwKEAjws5zABRDqkoOniLqfywESJACjdoiGZajN3zGsGaSqkDfrX5R4FAfvi6bPcF4Y0AeFxZ72HhoCJwnw_wcB%2526srcrot%253D711-117182-37290-0%2526rvr_id%253D1111809638243&ul_noapp=true
Thank you very much! cant wait to install on the 2014 matte grey veloster turbo I just bought. Still waiting for it to be delivered!
Adam Gottschalk Awesome! i really like the matte grey velosters. Hope you enjoy it.
what did you use as a baffle for this, if anything?
Adam Gottschalk Its got one built in