DIY: HOW TO REPLACE

/ @sajalazlanesh
DIY: HOW TO REPLACE MICRA K11 DISTRIBUTOR BEARING & OIL SEAL
this video brings you full detail on changing and inspecting the condition of distributor oil seal and bearing condition of Nissan Micra K11 z10 CG13 CGA3 engines.
when your engine distributor start leaking oil from distributor it means distributor o ring or internal seal worn out. so you need to replace it by dissembling the distributor properly. after installation of seal and bearing properly reassemble it confidently.
Welcome to our tutorial on replacing the distributor seal and bearing on a Nissan Micra. In this video, we will guide you through the step-by-step process of removing and replacing these components to keep your Micra running smoothly.
If you've noticed oil leaking from the distributor or a whining noise coming from the engine, it may be time to replace the seal and bearing. This maintenance task is essential to prevent further damage to your engine and ensure optimal performance.
To begin, you will need a few basic tools and replacement parts. Make sure to have a new distributor seal and bearing on hand before starting the job.
Follow along as we demonstrate each stage of the replacement process, from removing the distributor to installing the new seal and bearing. We'll provide helpful tips and tricks along the way to make the job easier for you.
Don't hesitate to reach out if you have any questions or need further assistance. We're here to help you get your Nissan Micra back on the road in top condition.
Thanks for watching, and be sure to like and subscribe for more helpful tutorials on car maintenance and repair.
#nissan #Micra #k11 #distributor
How to Adjust Sparkplug Gap on Micra
• Adjusting #Sparkplug G...
Detail on Mass Airflow sensor MAF
• Mass Air Flow Sensor: ...
Detail on Throttle position sensor TPS
• Throttle position sens...
Detail on IDLE CONTROL Valve IAAC FICD
• Idle Control Valve:Und...
Detail on Cleaning Hot Wire of Throttle body MAF sensor
• How to clean dirty Mas...
Detail on Solenoid starter armature winding check
• Car Solenoid Starter D...
#k11
#Micrak11distributor
#Nissanmicradistributorcap
#nissanmicrak11
#Howto
#Micrak11distributordisassembly
#scottykilmer
#Nissanmarchdistributor

[@cannaroe1213]

Wow dude, you are amazing at this!

[@user-de2di1gi6i]

very well explained. Thank you

[@atanasionhambongo2344]

O meu Nissan micra no distribuidor não chega corrente oque Faço?

[@SajalAzlanEsh]

On ignition and Check pin No.2 volts from left to right reference to ground. Also check capacitor wire volts (12) with ground. If no voltage then check ignition relay

[@SajalAzlanEsh]

Also check capacitor a small steel cap bottle with one wire if you have 6 pin distributor on the top of the volts

[@atanasionhambongo2344]

Já fiz isso douctor mas ainda.

[@SajalAzlanEsh]

​@@atanasionhambongo2344if volts coming to capacitor ua-cam.com/video/ujJdoeuLE_k/v-deo.html or if ignition coil is ok ua-cam.com/video/M9YJ2QaOo9g/v-deo.html then do the following

[@SajalAzlanEsh]

POWER TRANSISTOR Using an analog tester and measure the resistance between different contacts, changing the polarity. Pins
6 (+), 5 (-) = not 0 or infinity
6 (-), 5 (+)=not 0 or infinity
7 (+), 6 (-)=not 0 or infinity
7 ( - ) ,6 ( + )=infinity
5 (+), 7 (-)=infinity
5 (-), 7 (+)=not 0 or infinity
Note: Values ​​obtained digital tester will differ from those given above. Check the ignition distributor (rotor, distributor cap). At Replace components if necessary.