@daviddonahue1862 lol 😂 False. How many transmissions have you pulled in your life???? The last 500 transmissions I’ve pulled in the last 2 years or less have “survived” (not servived) perfectly fine. And no the o-rings don’t rip either lol. Please stop with the silly soft-boy myths. It’s hurting the industry.
Hey bro , I got a 2001 Chevy Suburban with a bad transmission. Whats yours advice on getting a cheap one and how much should I pay for installation? I’m in Orlando if you know a guy
It usually takes me around 1.5-2 hours at a easy pace, just pulled the 4L60 out of my truck this morning for a overhaul and to clean and repaint the frame since its getting a bit nasty under there as i saw today.
so if i want to keep the torque converter and flexplate to swap onto my 5.3 should i do it this way as well? pull trans... then torque converter? or should i take out the torque converter bolts and pull the trans and torque converter as 1 piece? then grab the flex plate. since its gonna go back onto my suburban?
If you’re doing it at home with a transmission jack with no potential falling impact it’s best to remove it in one unit, I remove the transmission first and torque converter afterwards because if you leave it in there’s a chance you can break the pump or damage the shaft it’s happened to me before, it’s just heavier and falls awkwardly and can get pretty dangerous Thanks for watching 🤙🏽👨🏻🔧
I'm going to try and find a 4x4 700r4 (later year around 92) at one of my local junkyards to fix my first vehicle ('92 Chevy Blazer) Do you come across those transmissions very often? Really love your content. Keep it up!
Yes sir I just pulled one of those last week!! I’ll record my next one! Yeah I come across them but they are getting a bit harder to find as time goes by Man, Thanks for watching I appreciate the support 🙏🏽🥹🙏🏽🥹🙏🏽🥹🦾👨🏻🔧🦾👨🏻🔧
Thus dude fliped the pan off with out touching it i bet everyone else had to pry theres off. Every one who didnt have to pry the pan off comment and help this guy out
Nice video. Would you do anything differently if you did it again? I have a 05 4x4 Yukon 5.3L. 233,000 miles. Looking to get a used cheap broken 4L60/65/70 to rebuild with my teen as a DIY learning project. To have ready. I found a used one for $60, with nothing but Reverse working. Thanks!
LOL man you took that apart so fast what'd you do work in a Chop Shop? You know I'm only joking correct? I know when you do this stuff for years you know exactly what you're doing and how fast you can do it I've been there
HAHAHAHA that was funny!! Thanks bro I appreciate the feedback and just like you said after 14 years I better be able to pull it off this fast lol!!! Thanks for stopping by 🙏🏽🦾👨🏻🔧 I have a lot more videos coming soon!
False. Last 500 transmissions I’ve pulled front seal bushing have never been harmed. Stop spreading fake info it’s not good for the industry. Or make videos explaining why and tag me later. It’s actually safer to remove the way I do it I’ve broke bell housings letting them slam on the floor before with torque converter inside. Go make some videos and teach me.
Oh and not a junkyard transmission. Spend some time in a professional shop working on automobiles and you will never see a transmission pulled with the torque converter still bolted to the flywheel unless the motor can not be rotated to get it out.
@johnrogers2849 I can get you $1000 I’ll do it faster than you any way you want yo do it princess. We don’t work off the book around here we get shit done
I believe your cousins own a shop in slc ut they specialize in swapping triton v8 and v10 in 99 to current f150 250 and superdutys got to buy jasper crate engine from them but u drop the truck off before 7am on weekday its done by noon or you drop it at noon and its done by 5pm that day its 3 brothers its all they do they are quick they do 2 a day its the crate engine price plus 1000 labor
So if I wanted too use one of these transmisssion out of an envoy or it’s all I can find how would I go about putting it in my 5.3 ls will the bell housing line up or would I have too use my old bell housing and torque converter?
Yes it’ll work just make sure the front shaft is the same some of the trailblazers have that ugly mini shaft with the tiny torque converter Sorry for the late reply been super busy these past couple months have 10 more videos getting ready to be uploaded 🦾👨🏻🔧🔩🙏🏽
Have you ever done it or are you just a keyboard warrior?? Has your life ever been saved multiple times by “propped rims” if the answer is no then keep your opinions to yourself leave the tough work to real men mija
Hahahahah I’ll attack rusty bolts the same way bro I’m 6’3 250lbs there ain’t a bolt on this planet I’m not cracking lol anyways thanks for watching 🦾👨🏻🔧🙏🏽
took me 2 days and 4 showers to do what this dude just did in 8 mins...
Hahahahah I just saw this 😂🤣😂 thanks for stopping by!!! (UA-cam is really weird about notifications)
No busted knuckles, like me? 😂
Lol
I'll be surprised if the pump servived...always remover torque converter/trans together.
@daviddonahue1862 lol 😂 False.
How many transmissions have you pulled in your life???? The last 500 transmissions I’ve pulled in the last 2 years or less have “survived” (not servived) perfectly fine. And no the o-rings don’t rip either lol.
Please stop with the silly soft-boy myths. It’s hurting the industry.
In news today 4l60 transmission pulled from customers car while parked in the U Pull lot. 😂😂😂😂. Have a good one 🍺
More like the transmission pulled from customers car while waiting in the drive through of Chik Fillet.
🤣🤣🤣🤣🤣🤣🤣 aww man these comments made my day thanks for watching I appreciate the feedback 🙏🏽🙏🏽🙏🏽🤣🤣🤣🤙🏽🤙🏽🤙🏽🤙🏽👨🏻🔧👨🏻🔧👨🏻🔧🦾🦾🦾🦾
@@clay500 🐥 🤣👨🏻🔧🦾🦾
Damn dude. Impressive. I thought you were pulling a 80 for that kind of speed and intensity 🤣
Thanks bro I appreciate it 🙏🏽🙏🏽🦾🦾🦾 hahahah those 80s are heavy!!!
Crew Chief and Pit President of Pick-N-Pull Pit Crew god damn son you were on a roll
Hahahaha!! Appreciate the love bro thanks for stopping by 🙏🏽🦾👨🏻🔧
Thanks for showing the attach mode. Got to do one for my dad tonight. Might still have a Sat thanks to you.
About to go pull one this weekend hopefully i can do it before the yard closes 🤣
Hahahahaha did you get her pulled????
Be better if ya got it done before they opened lol
Rumor is that someone could pull a transmission out in under 10 minutes. I lost a bet with myself. Didn't even have time to finish my popcorn
😅😅😅🍿🍿🍿 hahaha rewind it?!
@@Ajunkman.....😄!
This man…. Absolute machine. Usually takes me about 2-3 hrs but I don’t have any power tools. THIS MAN SHOULD BE CALLED THE JUNKYARD REAPER
🥲sheesh the reaper haha!! Thanks man I appreciate it thanks for stopping by 🦾👨🏻🔧
😂😂😂😂😂❤
You are the man. Mad props to you brother!!!
Thanks brotha 🙏🏽🙏🏽🙏🏽🦾🦾🦾
@@Ajunkman Very welcome Sir
This guy would stripp a hellcat in 30 mins 😂😂
Show me where it’s at I’ll try my hardest hahahaha thanks for stopping by 🦾👨🏻🔧🙏🏽
That was smart leaving the converter for last less weight to deal with, you are the first person I saw do it like that 👍🏿
Appreciate the comment bro thank you 🦾🙏🏽
Shit wish I could just throw the bolts around like that but I gotta put mine back together 😂
@@itchinforfishin8038 hahahahahahahahah
I do the same for a install
Video coming soon 😁
I betcha this guy can do a cat converter in 60 Seconds!!
Damn bruh you’re insane! Handled that shit like a boss! 💪🏿
I appreciate it bro thanks for stopping by 🦾👨🏻🔧🙏🏽
This gave me some confidence! Kinda was afraid to start on mine but now I’m trying to be you without cutting the lines of course😅
Hahaha don’t cut those bro!!! Appreciate the feedback thank you 🦾👨🏻🔧
Knowledge is power
Dammn that guy works hard!!!
Appreciate it 🦾🙏🏽
Good job Junk man. I like how u left the converter attached. That kills majority of your, fcn w/ that thing.
I did two trannies but they were four-wheel drive on envoy and it took me a week but I'm 62 also
Good job bro 🦾👨🏻🔧 thanks for stopping by 🙏🏽
This guy took the trans like it was a catalytic converter.
😂🤣😂 hahaha thanks for watching bro
That’s a new sub right there nice work 💯
Thank appreciate it🙏🏽
Damn what impact gun is that? I’m trying to pull the transmission out to get a rebuilt.
Yea...i did not think that was possible...wow. what about the transfer case and driveshafts though?
Thanks for stopping by! I have 4x4 videos too!!
Took bro longer to change sockets than anything image if he had a lift ... savage
Wish the socket can just appear in my hands I’ll be under 5mins for sure lol thanks for stopping by!! 🦾👨🏻🔧🙏🏽
Another great video. Thanks!
Got more coming!🙏🏽👨🏻🔧 appreciate it 🤙🏽
Hey bro , I got a 2001 Chevy Suburban with a bad transmission. Whats yours advice on getting a cheap one and how much should I pay for installation? I’m in Orlando if you know a guy
It usually takes me around 1.5-2 hours at a easy pace, just pulled the 4L60 out of my truck this morning for a overhaul and to clean and repaint the frame since its getting a bit nasty under there as i saw today.
Nice work bro! Hoped you got that thing painted away!! Thanks for stopping by 🦾👨🏻🔧
Very impressive. You got it down. Why did you leave the other bolts for the pan? I hope I Can work at those kinds of speeds.
Nice job
I have a 2007 avalanche 5.3 rwd needs a transmission
A 2007 envoy 4.2 will fit??
❤you rock!
Thanks for stopping by!! 🙏🏽😁
so if i want to keep the torque converter and flexplate to swap onto my 5.3 should i do it this way as well? pull trans... then torque converter? or should i take out the torque converter bolts and pull the trans and torque converter as 1 piece? then grab the flex plate. since its gonna go back onto my suburban?
If you’re doing it at home with a transmission jack with no potential falling impact it’s best to remove it in one unit, I remove the transmission first and torque converter afterwards because if you leave it in there’s a chance you can break the pump or damage the shaft it’s happened to me before, it’s just heavier and falls awkwardly and can get pretty dangerous
Thanks for watching 🤙🏽👨🏻🔧
I'm going to try and find a 4x4 700r4 (later year around 92) at one of my local junkyards to fix my first vehicle ('92 Chevy Blazer)
Do you come across those transmissions very often?
Really love your content. Keep it up!
I don't see many in Michigan just due to the cars or trucks rusted out 20 years ago. I would question anything in the yard that isn't a crash car.
Yes sir I just pulled one of those last week!! I’ll record my next one! Yeah I come across them but they are getting a bit harder to find as time goes by
Man, Thanks for watching I appreciate the support 🙏🏽🥹🙏🏽🥹🙏🏽🥹🦾👨🏻🔧🦾👨🏻🔧
@@KD0LRG yes sir! Anything not wrecked inspect thoroughly!
U make it look so easy lol
I thought i was good at 1hr put i also pull the pan first see if the clutche are in the pan and i pull the convert bolts threw starter hole
If I did it like this on my truck how would I ever be able to put it back together! 😂
It’s not meant to do it on your truck 🤣
Go to the junkyard and have fun! 👨🏻🔧
Thus dude fliped the pan off with out touching it i bet everyone else had to pry theres off. Every one who didnt have to pry the pan off comment and help this guy out
Hahahha sometimes people gorilla glue their pans back idk why sometimes I have to pry it off too 🫣 thanks for stopping by!!!! 🦾👨🏻🔧🙏🏽
He came prepared with tools.
Where did all the oil go?
Can you put 1 on for under 8 minutes too?
Nice video. Would you do anything differently if you did it again? I have a 05 4x4 Yukon 5.3L. 233,000 miles. Looking to get a used cheap broken 4L60/65/70 to rebuild with my teen as a DIY learning project. To have ready. I found a used one for $60, with nothing but Reverse working. Thanks!
Hope that rebuild project is coming along!!!
Amazing
How come you did not take the oil pan out before to see the moment of true?
Sometimes they just smell so good!
LOL man you took that apart so fast what'd you do work in a Chop Shop? You know I'm only joking correct? I know when you do this stuff for years you know exactly what you're doing and how fast you can do it I've been there
HAHAHAHA that was funny!! Thanks bro I appreciate the feedback and just like you said after 14 years I better be able to pull it off this fast lol!!! Thanks for stopping by 🙏🏽🦾👨🏻🔧 I have a lot more videos coming soon!
Dude what are you doing tomorrow..😅true master..
Damn that was a clean fluid pan your lucky as hell
She was a beauty 🦾
Parks Galore? I hear a train in the background
I saw that thumbnail of someone carrying a big auto transmission and my mouth dropped open. m15 caps suck
Haha!! I almost put one on my shoulder today for the next thumbnail! Maybe tomorrow 🤣 thanks for watching bro 👨🏻🔧🙏🏽
I remener being abale to move that fast under a car, but now there is no chance i can remember those scocket sizes that fast. Lol.
Lol
Hahahaha you got this bro.!!! Thanks for stopping by 🙏🏽🦾👨🏻🔧
Loose nuts are flying everywhere! This guy is a master
🔩⚡️🔩⚡️🔩⚡️I appreciate the feedback brotha 🙏🏽🦾👨🏻🔧 thanks for stopping by !!
This mf so cold ice would get jealous 😂, yo I need to be down with this cat as much work as I see around the crib.
Hahahahaha thanks man 🧊 I appreciate you stopping by 🦾👨🏻🔧
What is better to rebuild a transmission or get another one from junkyard
Try a junk yard bro find truck that’s smashed in the front that’s usually a good bet
Smart man! What this guy said ☝🏽
Appreciate y’all for stopping by 🦾👨🏻🔧🔩
torque converter needs to be unbolted before removing the transmission if you are trying to save the front seal and bushing.
False. Last 500 transmissions I’ve pulled front seal bushing have never been harmed. Stop spreading fake info it’s not good for the industry. Or make videos explaining why and tag me later. It’s actually safer to remove the way I do it I’ve broke bell housings letting them slam on the floor before with torque converter inside. Go make some videos and teach me.
@@Ajunkman You are honestly telling me you believe that is the proper way to remove a transmission?
Oh and not a junkyard transmission. Spend some time in a professional shop working on automobiles and you will never see a transmission pulled with the torque converter still bolted to the flywheel unless the motor can not be rotated to get it out.
@johnrogers2849 I can get you $1000 I’ll do it faster than you any way you want yo do it princess. We don’t work off the book around here we get shit done
Lmao. I’m at a junkyard not at a professional shop Mija.
Very good camera angles!
I appreciate it!!! 🙏🏽🦾👨🏻🔧
how did you lift this back in your car?
With my arms lol
No flywheel bolts to be romoved?
Great video……. Awesome work👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼
Thank you very much 🙏🏽👨🏻🔧
I believe your cousins own a shop in slc ut they specialize in swapping triton v8 and v10 in 99 to current f150 250 and superdutys got to buy jasper crate engine from them but u drop the truck off before 7am on weekday its done by noon or you drop it at noon and its done by 5pm that day its 3 brothers its all they do they are quick they do 2 a day its the crate engine price plus 1000 labor
That's a nice catch.......scored👍🏻
Yes sir she was a beauty 👨🏻🔧🤘🏽
Brings me back to when I did one of these transmissions with a friend. You are beast brother. We can tell this isn’t your first time doing it lol
Make a video for removing a 2006 accord v6 engine lol I need one and don’t know how to
So if I wanted too use one of these transmisssion out of an envoy or it’s all I can find how would I go about putting it in my 5.3 ls will the bell housing line up or would I have too use my old bell housing and torque converter?
Yes it’ll work just make sure the front shaft is the same some of the trailblazers have that ugly mini shaft with the tiny torque converter
Sorry for the late reply been super busy these past couple months have 10 more videos getting ready to be uploaded 🦾👨🏻🔧🔩🙏🏽
What brand socket swivel are you using?
Snap on 1/2” part no. IP80D
Best swivel I’ve ever used 7 years deep with this one
Damn you were ROLLING
Appreciate it brotha 🦾👨🏻🔧
8 minutes lol 😂
Guys a legend 😅😂
How much do they cost you
Thanks for watching! 🙏🏽👨🏻🔧
A couple hundred bucks
What kind of impact are you using? Where can I get me one of those?
Should leave the 4L60 in the junk yard. Scrap transmission lol
mine has 269,000 on it. is that junk?
Lol
Often rebuilt wrong, often not upgraded correctly to solve the known pitfalls, and often towed in overdrive...
How long to uninstall a couple cats??
😂😂😂
Hahahahahaha 🤣🤣
Damn job well done
Thank you very much 🦾👨🏻🔧🙏🏽
Takes me 2 hours maybe lol god damn
Hahaha thanks for stopping by bro🙏🏽 been doing this my whole life 🥴🦾👨🏻🔧
What an inspiration this guy is. So all I need is 13mm and 15mm.
Where is it?
That was badass bro!!
Appreciate you bro 🦾🙏🏽 thank you
At 6:42... what was the rubber hose ?
Breather hose
Not your first rodeo lol
🤠 lol no sir
🤢🤢🤢🤢🤢🤢
What do you do with them? Resell them or rebuild or??
All of the above brotha 👨🏻🔧
How much u pay for them
$350-$400
wow great work ur fast
Thanks bro I try 🙏🏽👨🏻🔧 thanks for watching 🤙🏽
Slam dunk my man
Yes sir!!🙏🏽👨🏻🔧😎
Took you 8 minutes bcos u doing that for living and probably already pulled out hundreds of them
@@solmora6495 well yeah. How else. Lol. Enjoy. Thanks for the view 👍🏽
🤘
🤙🏽🤙🏽
When you don't care it's easy to pull
Caring is for women or soft men
More like 30 to 60 minutes... u probably edited this video
🤣🤣🤣🤣 I have 100+ other videos of me doing it in under 10-12mins.
Stop hating.
First time doing this huh…? You’ll get faster. 😂😂
@@joshbryant7363 show us how lil hater 😂🤣😂 I don’t see any videos on your account?
How can propping a vehicle on rims be safe? i mean come on!!!
Have you ever done it or are you just a keyboard warrior??
Has your life ever been saved multiple times by “propped rims” if the answer is no then keep your opinions to yourself leave the tough work to real men mija
Take a chill pill dude your blood pressure is going up!@@Ajunkman
@@budthechud3408 lol what a womanly response. Take care. Show your face online if you’re going to be critiquing.
@@Ajunkman lay off the roids dude seriously! the alpha act is played out and pathetic!
Dude stole it😂
Throw it over the fence! Lol
No way that's up north. Every bolt would have been a problem 😂💯
Hahahahah I’ll attack rusty bolts the same way bro I’m 6’3 250lbs there ain’t a bolt on this planet I’m not cracking lol anyways thanks for watching 🦾👨🏻🔧🙏🏽
Nope
🤡
Yes Mike. Yes.
Rock Star
Thank you 🙏🏽 🦾😎
Are you in Tx if so I have a job for you since you can do it in 8 mins....think i just lost my transmission.
Lol! Sure $1000/hour 👨🏻🔧😂