the way the new rear main seal slid in i would be very worried about losing oil lol. We Americans call this a "Dirty backyard rebuild". No resurfacing, no measuring any surfaces or new parts. full trust in manufactured parts. Slap it together and go. Good work man. Damn. even painted every single machined surface, pulley, and linkage point rofl
*_What an amazing piece! I have never seen anything like it. I can't imagine how much time went into restoring it, let alone your skill and talent. Bravo!_*
Thanks a lot. We hope all the videos we make are well received by you. If possible, follow the video and fix your own device. Please follow and support us!
No honing the cylinder walls for new rings? (Must be a low mileage engine) How bout some thread locker as well? Otherwise…. Overall very efficient & quite clever at times. The paint scheme is a bit garish, but they did bang out the dented oil pan, that was cool!
Excelente trabajo con el baño de potasa a pincel y una obra de arte el plano de tapa de cilindro y block con amoladora. Se necesita tener un pulso nanométrico para lograrlo. Y el bruñido de cilindros con lija al agua, es de otro nivel, igual que los asientos de válvula con amoladora recta y taladro. Mis felicitaciones! 😄
Always the genius boy restores all these old things into an impressive masterpiece... I always love this youtube channel because it is number 1 on the list of the most fabulous restorations🛠️🛠️🛠️🔧🔧🔧♥️♥️♥️😎😎😎
А как же расточка коленчатого вала до ремонтного цилиндра? А хонингование цилиндров? Зачем использовать те же цилиндры и те же кольца? Я надеюсь он хотя бы шатунные и коренные вкладыши поменял, хотя без расточки он при протяжке может затянуть из так что потом не провернуть. В таком ремонте смысла нет
I have to speed up--sort of editing--this and many other videos like this one, in which they try to film every single bolt and pieces they're taking off and putting back--from start to finish. They want to record continuously without hardly making cuts somewhere in between. That is not necessary. You take just two bolts off and we, the viewers, get the point; then you change to a different video shots which they are all related to what you're doing.
Frage, beim Kolben einsetzen wurden die Kolbenringe nicht richtig verdreht . Bei drei Ringen um 120 crad von der Kraftabgebende Seite entsprechend der Drehrichtung des Motors.LG DDR Autoschlosser 1981
QUE EN POCO TIEMPO TENDRA HABERIAS PREMATURAS...POR DESIDIAS EN EL MONTAJE 😢😢😢😢NO SE LE VE UN SOLO DETALLE DE PROFECIONAL QUE PENA😮😮😮QUE NADIE PUEDA APRENDER NADA MEJOR DE LO QUE HACE..😢😢😢😢
А я покрашу генератор в синий цвет он был без цветным но а синим ещё нет😊. Молодец👏👏👏руки из плеч растут!
Here in Africa we don't have necessary tool's just like you do,i can repair tricycle but not as good as you are 👍👍
Thank you very much. Please follow and support us!
Пакистанцы отдыхают, со своим ремонтом🤣
Troche wątpię, że to był ten silnik znaleziony w błocie
the way the new rear main seal slid in i would be very worried about losing oil lol. We Americans call this a "Dirty backyard rebuild". No resurfacing, no measuring any surfaces or new parts. full trust in manufactured parts. Slap it together and go. Good work man. Damn. even painted every single machined surface, pulley, and linkage point rofl
That was hard to watch!
Ещё один замечательный пример т.н. "керосинового ремонта"
This machine manufacturing factory will not recognize the machine and laugh at the colorful creations 😀
*_What an amazing piece! I have never seen anything like it. I can't imagine how much time went into restoring it, let alone your skill and talent. Bravo!_*
Классаная работа 👌👌
Thank you very much.
あなたの仕事はとても良いです。 定期的にフォローさせていただきます。
Thanks a lot. We hope all the videos we make are well received by you. If possible, follow the video and fix your own device. Please follow and support us!
JagoanKampung Channel : mantap
Thank you very much . Please always follow and support us!
@@restorationsskills4967 saya sangat suka kreasi anda anda membuat saya iri akan keahlian anda
From Egypt good working
Thank you very much. Please follow and support us!
Parabéns ao mecânico! Trabalho Nota 10.
Thank you very much. Please follow and support us!
Brilliant job, very satisfying sir!
Thank you very much. Please follow and support us!
I wouldn't even recommend this tinkerer to my worst enemy.
No honing the cylinder walls for new rings? (Must be a low mileage engine)
How bout some thread locker as well?
Otherwise…. Overall very efficient & quite clever at times.
The paint scheme is a bit garish, but they did bang out the dented oil pan, that was cool!
And the 7/8"Gangsley Sprocket Wrench....for your harmonica balancer..! 👍
Thank you
Impressionante, porque não Lavou esse motor antes de trabalhar nele 🙎🙎
Thank you very much.
Excelente trabajo con el baño de potasa a pincel y una obra de arte el plano de tapa de cilindro y block con amoladora. Se necesita tener un pulso nanométrico para lograrlo.
Y el bruñido de cilindros con lija al agua, es de otro nivel, igual que los asientos de válvula con amoladora recta y taladro.
Mis felicitaciones! 😄
สุดยอดช่างเลยครับ
Thank you very much. Please follow and support us!
لم اكن اتوقع انجازه بهذه الطريقة.. احب فيدواتك لانكما تعملان بصمت..
اهنيكما وشكرا لكما
Похож на старый добрый ПЕРКИНС.
Thank you
Похож на старые добрые д-240
ช่างแก่งมากๆๆ❤🎉😮
Thank you very much. Please follow and support us!
Always the genius boy restores all these old things into an impressive masterpiece... I always love this youtube channel because it is number 1 on the list of the most fabulous restorations🛠️🛠️🛠️🔧🔧🔧♥️♥️♥️😎😎😎
Sempre que digo, são realmente fantásticos, os admiro muito.😄😃
Thank you very much
по сравнению с носителями сандалий, это прямо операционная
Good Skill 👍👍
Thank you very much. Please follow and support us!
а почему поршни не покрасили?
Файна робота
Thank you very much. Please follow and support us!
الله يبارك 👏👏💯💯💯👍🙏
จริงๆครับผมเหตุผลเหล็กกล่องตัวC/H/I/Oเหล็กกลมไม่ใช่เหล็กตันน้ำหนักต่างกันกล่องลดขนาดเหล็กความหนาลง.แรงซับ🚘🛵ด้านหน้าด้านข้างด้านหลังต่างกันตามความเร็วของ🚘เบรคไม่ได้ช่วยลดแรงเฉี่อยลงเบรคแค่ผ่อนแรงถนนรับแรงเบรคไถลไปกับพื้นถนนยาง...ตกลง🚘🛵ใครผิด🥰🥰✌
Thank you
Toujours le maître
Good job
Thank you very much. Please follow and support us!
this guy is good
Thank you very much. Please follow and support us!
PARAB;ENS PELO BELO TRABALHO GOVERNADOR VALADARES MG BRASIL
Wow good❤❤❤❤
Thank you very much. Please follow and support us!
И таких мастеров пруд пруди... Мда... Куда катится мир - это просто трэш
Super jest to odrestaurowane ten bardzo stary śliniak od Audi B3 80 pozdrawiam serdecznie 👍👍👍👍
Thank you very much . Please always follow and support us!
you are a great mechanic
Sao rửa bằng nước trước khi rã máy vậy
Ficou bonito o motor
Thank you very much. Please follow and support us!
Good and hard skill job thanks
Thank you very much.
Excellent hard work. 👏
Bagus memperbaiki mesin
Thank you very much. Please follow and support us!
Diesel engine sound fan's like here👇🏻😂
The folloving video is the restoration of the gearbox from this engine)
perfecto 👌
Thank you very much. Please follow and support us!
Why not clean the dirt on the surface with a water gun before disassembly? Washing can clean a lot of dirt.
Thank you for your feedback so we can improve future products. Wish you good health.
Gostei passeiro belo trabalho
Thank you very much. Please follow and support us!
You never crack the head bolts loose from the center out! It’s out to in.
Hey genius, doesn't matter which way you go
Also, that dirty fuel he was cleaning the injector nozzles with. I would have been fired! 13:53
the whole engine build was dirty. i would never get these guys to build an engine for me.
Да ремонт помыл походит
Nice work
Thank you very much . Please always follow and support us!
The Water Hose is bent/twisted....
🎉Like~
Why are you not replacing the liners.
O Cara pinta o motor sem proteger as partes internas kkkkkkkkkkkkkk
Excelente profissionais.🙋👍👍👍
THANKIOUPR❤❤❤❤❤❤❤❤❤❤❤❤❤
Thank you very much. Please follow and support us!
49er❤❤❤
Thank you very much. Please follow and support us!
хорошо блок крышка клапанная покрашены но элементы топленой аппаратуры форсунки и вишенка на торте корзина сцепления это особый вид тюннинга?
ก่อนพ้นสีดูสวยกว่าเยอะ จริงๆถ้าจะทำสีควรพ้นสีก่อนใส่น็อต 😂😂
Nice work, save you back. Get a higher table to work properly work on, your back will be happy with you later in life.
Thank you very much . Please always follow and support us!
😉😉👍👍
الله يبارك ويزيد 👍👍👍
Silastic on the bellhousing was a bit weird ….rear main isn’t fitted to bellhousing so there is no oil on it !!!
Lóc máy lấy máy mài tay đánh 😂😂😂😂
No one on this channel ever hones the cylinder walls for some reason.
No seven lo queen es buñir
Tampoco maiden six esta osvaldo el cilantro ni la altera de pistones
Туда болгарка не пролезает😂
👍👍👍👍👍👍
Chú sửa tốn hết bảo nhiêu
Depending on the damage, our team of workers is very skilled so the repair cost is not very expensive
А как же расточка коленчатого вала до ремонтного цилиндра? А хонингование цилиндров? Зачем использовать те же цилиндры и те же кольца? Я надеюсь он хотя бы шатунные и коренные вкладыши поменял, хотя без расточки он при протяжке может затянуть из так что потом не провернуть. В таком ремонте смысла нет
I have to speed up--sort of editing--this and many other videos like this one, in which they try to film every single bolt and pieces they're taking off and putting back--from start to finish. They want to record continuously without hardly making cuts somewhere in between. That is not necessary. You take just two bolts off and we, the viewers, get the point; then you change to a different video shots which they are all related to what you're doing.
Thank you for your feedback so we can improve future products. Wish you good health.
KEREEEN..
Engineers from Lidl😂😂😂
Thank you
Зачем разбирал двигатель,???? Помыл и хватит😅
The engine has been broken for quite some time. we need to restore it to its original working state
А покрасить?????
❤❤❤❤❤❤❤❤❤
Incredible they reused parts without a proper cleaning. I hope those gasket surfaces are flat enough to last 20 years.
I know!!! they made soo much work and didnt resurface the important parts, i feel its a crime
Also I just noticed they painted some contact surfaces and the interior of the exhaust port. terrible!!!
10
Pas d'huile sur les coussinets de bielles et paliers ???
Frage, beim Kolben einsetzen wurden die Kolbenringe nicht richtig verdreht . Bei drei Ringen um 120 crad von der Kraftabgebende Seite entsprechend der Drehrichtung des Motors.LG DDR Autoschlosser 1981
Rồi cây cần lực siết như zậy hả ta 😂😂
От чего двигатель?
Love the kinked water hose....otherwise a great rebuild..
yeah, I winced a little too when he lapped the valves and then proceeded to mix them all up. Overall, for a patio rebuild, not too bad.
❤🎉 great
Sound 1.9 TDI
You god 1342😂❤
Do you need an engine?boss
Thank you very much. If you have an old broken engine, please send it to us
😅😅😅😅👍👍👍
Porque no lo lavan antes de desmontarlo? Son poco professionales
Thank you for your feedback so we can improve future products. Wishing you good health
❤
Why would you grind a new seat and valve together then turn around and mix them all up afterward😢
КОЛХОЗ КОЛХОЗНЫЙ .
Why would you want to replace something like this. This engine needs 1 wire to run. Modern engine needs 125 sensors to to turn over.
Почти пакистанский ремонт
👍👍👍👍🚔🇮🇩
Vrh❤❤❤❤❤
Thank you very much. Please follow and support us!
NOW THAT HE REDUE THE ENGINE WHAT DOES HE DO WITH IT
QUE EN POCO TIEMPO TENDRA HABERIAS PREMATURAS...POR DESIDIAS EN EL MONTAJE 😢😢😢😢NO SE LE VE UN SOLO DETALLE DE PROFECIONAL QUE PENA😮😮😮QUE NADIE PUEDA APRENDER NADA MEJOR DE LO QUE HACE..😢😢😢😢
😮😮😮
😂😂😂 кого вы пытаетесь обмануть постанова чистой воды 😂😂😂
had a kinked up smashed water hose between the pump and the thermostat that's not going to allow any water to flow
Thank you for your feedback so we can better improve future products. Wishing you and your loved ones good health!
Worst restoration i ever seen you should spray paint inside the combustion chambers
Wash the engine before disassembling keep all that sand out of it
Thank you very much
Как называется ?
You forgot to paint the crankshaft and pistons
😂😂😂
Uh
😂😂
They don't need paint bcz they are inside piece's.
@@luigipellegrini92you should take some sarcasm classes