I used this video today to install Siouxicide Choppers bars. The video was perfect. When resassembling, I had a specific question about which port to install the little plug on the clutch side into so I watched another video for that since this one didn't touch on it. This is, by far, the best video out there. You do NOT need to remove your fuel tank, fairing, etc. "Your B G" did a good job figuring this out.
i dont mean to be so off topic but does any of you know of a tool to get back into an instagram account..? I was dumb lost the login password. I would appreciate any tips you can give me!
@Axl Gustavo I really appreciate your reply. I got to the site through google and I'm waiting for the hacking stuff now. Seems to take a while so I will get back to you later with my results.
Bought a set of these bars. Waited over a month for them to arrive and just installed them. They are not drilled for the locating post on the Indian switch housing. Had to melt the locating posts off both switch housings to install them on my 2020 Challenger. It was either that or drill the holes in the handle bars, which would be tough to get located correctly. Finish on these bars isn't that good for powder coat. They scratch too easily. If I knew what I know now, I would buy a different brand that has the drilled switch housing location holes already in them.
I second this comment, quality on the bars was average. Once installed they also touch the inner side of the fairing. Not to mention they were very difficult to get ahold of and did not respond quickly at all. Minor things overall, BUT... buyer beware.
Random question. Where did you get the bike stand in the video from? I got one from Harbor Freight years ago but the part I put my kickstand down in is too short, nothing like in this video. Also seems to be just a few inches short wheel base wise.
I bought these bars and getting nervous cause I've sent torch industries questions about my order and I've gotten no response from them. Paid through PayPal and I bought them because of your vid on UA-cam. Can you reach torch directly?
@@AnonymousBosch3158 the Torch bars felt good at first, but you had to mod your control housing due to no hole in bar, 2nd the torch bars can only be adjusted so far the bars will hit your tank turning left and right. At the position where it will turn makes you sit up and in an aggressive position therefore after 2 hrs your back is screaming with discomfort. Torch is aware of this issue on their first roll out and may have made changes by now.
@@bluezuke860 I THINK THESE ARE ACTUALLY WHAt i wan't.. i have long arms.....i don't want bars that come back , to me. and i'm thinking more like 11"-12" high.
I used this video today to install Siouxicide Choppers bars. The video was perfect. When resassembling, I had a specific question about which port to install the little plug on the clutch side into so I watched another video for that since this one didn't touch on it. This is, by far, the best video out there. You do NOT need to remove your fuel tank, fairing, etc. "Your B G" did a good job figuring this out.
Thank you for the video , i just put my KST 14" hand bar . i just loved my bar ...looks rock...
He answered everybody that DIDN'T ask what size bars they are. And still hasn't lol
How many inches is your bar?
I love the torch bars.
thank you me too!!!!
How's the long distance arm fatigue on these vs the stock bars??
Did you put the bar end weight back in the new bars on clutch side ?
What is the pullback..in inches..on these bars?
What’s your thoughts of the difference between your torch bars and your buddies kst bars?
Torch Bars, How tall ? 10/12/14 ? also, did you run the same issues as per John MCCormick with the Locating posts?
For some reason, they don't want to answer this lol
FUCKING BAD ASS !!! I've made up my mind. I'm trading in my Roadglide. Thank you !!!
WHAT SIZE BARS ARE THOSE??
Did you have to replace the cables when you put these bars in? If so which length did you go with?
One of the best removal videos I’ve seen. Can’t wait to get my bars in next week, thanks!!!
i dont mean to be so off topic but does any of you know of a tool to get back into an instagram account..?
I was dumb lost the login password. I would appreciate any tips you can give me!
@Forest Ismael Instablaster ;)
@Axl Gustavo I really appreciate your reply. I got to the site through google and I'm waiting for the hacking stuff now.
Seems to take a while so I will get back to you later with my results.
@Axl Gustavo it did the trick and I now got access to my account again. Im so happy!
Thanks so much, you really help me out!
@Forest Ismael glad I could help :)
Bought a set of these bars. Waited over a month for them to arrive and just installed them. They are not drilled for the locating post on the Indian switch housing. Had to melt the locating posts off both switch housings to install them on my 2020 Challenger. It was either that or drill the holes in the handle bars, which would be tough to get located correctly. Finish on these bars isn't that good for powder coat. They scratch too easily. If I knew what I know now, I would buy a different brand that has the drilled switch housing location holes already in them.
I second this comment, quality on the bars was average. Once installed they also touch the inner side of the fairing. Not to mention they were very difficult to get ahold of and did not respond quickly at all. Minor things overall, BUT... buyer beware.
@@erikj6128 Did you melt off the locating posts or cut off the locating posts?
How tall are you in? I'm five-ten. Great video
Brandon I have a set of the polished mid riser Indian bars with Upgraded Indian grips ready to. 602.677.2570
Random question. Where did you get the bike stand in the video from? I got one from Harbor Freight years ago but the part I put my kickstand down in is too short, nothing like in this video. Also seems to be just a few inches short wheel base wise.
I would like to know also. I’m in the market for a stand
Handy Industries is what you want👍
Why dont they make challenger bars atleast 16-18 inches tall or plus 10 instead of plus 8s
Torch ind seems to be OOB?
Great video. Thx
WHY DID U CHOOSE THESE OVER THE INDIAN MIDRISE BARS?? JUST ASKING CAUSE IM LOOKING TO BUY ME SOME BARS FOR MINE SO JUST WANTED TO KNOW.
I bought these bars and getting nervous cause I've sent torch industries questions about my order and I've gotten no response from them. Paid through PayPal and I bought them because of your vid on UA-cam. Can you reach torch directly?
Beautiful Bike!
What is the diameter of the bars?
I would have to check but i think its 1.5 or 1.25
Repost?
yes, had to edit it!!! thanks for watching brother!
►GD MOTOVLOG MERCH: shop.spreadshirt.com/gdmotovlogs/ CUSTOMIZE YOUR GD MOTOVLOGS BIKER MERCH!
►Subscribe to my channel here: goo.gl/xBXKuF
I hated these dam bars! Removed them within a week. Went with Dirty Bird.
Why?
Did you do the short or tall dirty bird bars? I am looking for bars for my challenger right now.
@@AnonymousBosch3158 the Torch bars felt good at first, but you had to mod your control housing due to no hole in bar, 2nd the torch bars can only be adjusted so far the bars will hit your tank turning left and right. At the position where it will turn makes you sit up and in an aggressive position therefore after 2 hrs your back is screaming with discomfort. Torch is aware of this issue on their first roll out and may have made changes by now.
@@bluezuke860
I THINK THESE ARE ACTUALLY WHAt i wan't..
i have long arms.....i don't want bars that come back , to me. and i'm thinking more like 11"-12" high.
I saw this bike for sale on Cycle Trader I want it ... I messaged thru cycle trader please hit me back!