I noticed on the linkages, some people with the same carb have a little notch on the throttle side, so when it accelerates that notch pushes the choke linkage upwards. Not sure if it's necessary or not but I wonder why some have one and some dont.
Can you buy just the linkage? Mine had a threaded barrel type deal where the throttle cable attached and some idiot (me) over-tightened it and broke it off. I currently have a rebuild kit with brass floats and choke kit in my cart from your place.
Would a can of carb cleaner work or is the dip better for cleaning? Mine isnt horribly dirty but my engine is running rough and figured I would try cleanig carb and hate to loose the paint on it.
Hey mike is there any place to get the air mixture screw? The carb on the boat that my son bought is missing and probably why it’s not running for crap. It’s a mercarb
My Choke plate is kind of stuck and its sometime hard to move when its close most of the part. Is there anyway or how I can clean that to make it run smooth? BTW, its not able to close all the way, not sure it suppose to be the way it is?
You should remove the carburetor and take the choke valve out for a good cleaning. At the same time look around for a part that might be causing it to bind. Remove the linkage and see if the valve sticks without it.
Hey Mike, the "main jet" (brass) is disintegrating instead of unscrewing. Any tips to remove it safely? I know you said there's a new one included in the kit but I need to get the old one out first!
Thank you so much for your video it is very detailed and helpful. Quick question the "power piston" is stuck solid. No movement at all, I used the All as you demonstrated and nothing. I mean it is frozen solid. I tried a little bolt buster to see if it would lose it up nothing... so I went ahead and have it in the chem dip overnight and will try again in the morning to see if it broke it free. I saw your video on heating the housing like the Roch will that work on this model Merc? Any suggestions would be greatly appreciated. Thanks again
You need a 8 mm wide screwdriver for those jets(both have 145s in 2 mercarbs i'm cleaning now); no ,ere ,no less,MUST be 8 mm; grind down one,or go buy,borrow,steal... 8 mm. did i say 8 mm ,already? more,and it won't fit; less and you'll make those (soft brass)jets look like shtt,whether you're able to remove them (to clean them--with --soft---copper wire strands!) or not; and yes, i have seen them with so much varnish and white powder in the orifice,that the size goes down to 125 (that's 1.25 mm) before cleaning; that means LEAN combustion at full throttle,and that means bad news for those pistons!!!
@@MikesCarburetor Berryman's has worked well for me. Can be bought in a 16 ounce can for general cleaning; but the gallon can, with the included strainer, is best for dipping. I'm not a professional; just a home/farm mechanic; so your validation or exhortation on this would be appreciated. I'll try the Simple Green, too. Thanks for the outstanding video and advisement. :)
HI. yesterday i water tested a searay 185 sport with a mercarb on a 4.3 that i just went through. it ran for about 3 minutes then lost power and stalled. looking down into the throat of the carb you can see fuel dripping out of the venturis. during assemblu i checked the float level and it meaured pretty close to the chart. so i dont know if its a float problem causing it to flood, or if there is something else going on. any ides? thanks.
Well,Mercruiser did a number on us,on some they put a STEEL gas line from pump to the carb.; it RUSTS baddly inside ,and the rust goes thru the inlet screen at the carb's entrance(no filter there)and keeps the needle open; if you hit the carb with a RUBBER mallet while the engine is idling and fuel is flooding down the intake,it will stop,but tomorrow it will do it again; you need to clean the STEEL pipe inside; run a wire,(thick electrical wire with frayed end,strands opened, flexible speedometer cable ,etc) and you'll see what comes out; everytime it sits empty,it will rust; (it's illegal and dangerous to replace it with a rubber line,never do that in a gas boat).
Just ordered a kit and float for my 1389-8490 Mercarb , tried to call but couldn't get anyone . just hope it's the right kit . Already bought one at my local dealer and it was the wrong kit .
Merci beaucoup ❤❤❤❤❤❤
Nice and clean, not the case with mine. How do you handle stuck gaskets that come off in pieces without scratching or gouging the metal?
Very nice explanation video, thank you
I noticed on the linkages, some people with the same carb have a little notch on the throttle side, so when it accelerates that notch pushes the choke linkage upwards. Not sure if it's necessary or not but I wonder why some have one and some dont.
This is why fuel injection was created.
Can you buy just the linkage? Mine had a threaded barrel type deal where the throttle cable attached and some idiot (me) over-tightened it and broke it off. I currently have a rebuild kit with brass floats and choke kit in my cart from your place.
@@MikesCarburetor thank you for the reply
Is this something a novice with little engine/carb experience could do? My merc 3.0L carb may need to be rebuilt and was thinking of doing it myself.
Would a can of carb cleaner work or is the dip better for cleaning? Mine isnt horribly dirty but my engine is running rough and figured I would try cleanig carb and hate to loose the paint on it.
Do you have a video on taking it out of the boat?
Sorry no. We focus on the carburetor only.
Hey mike is there any place to get the air mixture screw? The carb on the boat that my son bought is missing and probably why it’s not running for crap. It’s a mercarb
I just bought from your website. I don’t have one to compare so I’m hoping it’s right Thanks
My Choke plate is kind of stuck and its sometime hard to move when its close most of the part. Is there anyway or how I can clean that to make it run smooth? BTW, its not able to close all the way, not sure it suppose to be the way it is?
You should remove the carburetor and take the choke valve out for a good cleaning. At the same time look around for a part that might be causing it to bind. Remove the linkage and see if the valve sticks without it.
@@MikesCarburetor thanks Mike. So that’s the part you are not recommended to do in your video, right?
@@davidqi8073 Only if you have to but I'll bet something in the linhkage is causing the problem.
Hey Mike, the "main jet" (brass) is disintegrating instead of unscrewing. Any tips to remove it safely? I know you said there's a new one included in the kit but I need to get the old one out first!
Never mind, I got it. (Combination of locking pliers and 3/8" flat screwdriver.) But I'm sure glad I'm not reusing the old trashed one!
Thank you so much for your video it is very detailed and helpful. Quick question the "power piston" is stuck solid. No movement at all, I used the All as you demonstrated and nothing. I mean it is frozen solid. I tried a little bolt buster to see if it would lose it up nothing... so I went ahead and have it in the chem dip overnight and will try again in the morning to see if it broke it free. I saw your video on heating the housing like the Roch will that work on this model Merc? Any suggestions would be greatly appreciated. Thanks again
Did u figure it out?
My power piston wont come out and the splash shield was missing when I disassembled the carb. Any help with this Mike?
What’s splash shield?
You need a 8 mm wide screwdriver for those jets(both have 145s in 2 mercarbs i'm cleaning now); no ,ere ,no less,MUST be 8 mm; grind down one,or go buy,borrow,steal... 8 mm.
did i say 8 mm ,already? more,and it won't fit; less and you'll make those (soft brass)jets look like shtt,whether you're able to remove them (to clean them--with --soft---copper wire strands!) or not;
and yes, i have seen them with so much varnish and white powder in the orifice,that the size goes down to 125 (that's 1.25 mm) before cleaning; that means LEAN combustion at full throttle,and that means bad news for those pistons!!!
The cleaning solution you recommended is Dip? Is that the name brand?
@@MikesCarburetor Berryman's has worked well for me. Can be bought in a 16 ounce can for general cleaning; but the gallon can, with the included strainer, is best for dipping. I'm not a professional; just a home/farm mechanic; so your validation or exhortation on this would be appreciated. I'll try the Simple Green, too. Thanks for the outstanding video and advisement. :)
HI. yesterday i water tested a searay 185 sport with a mercarb on a 4.3 that i just went through. it ran for about 3 minutes then lost power and stalled. looking down into the throat of the carb you can see fuel dripping out of the venturis. during assemblu i checked the float level and it meaured pretty close to the chart. so i dont know if its a float problem causing it to flood, or if there is something else going on. any ides? thanks.
Well,Mercruiser did a number on us,on some they put a STEEL gas line from pump to the carb.; it RUSTS baddly inside ,and the rust goes thru the inlet screen at the carb's entrance(no filter there)and keeps the needle open; if you hit the carb with a RUBBER mallet while the engine is idling and fuel is flooding down the intake,it will stop,but tomorrow it will do it again; you need to clean the STEEL pipe inside; run a wire,(thick electrical wire with frayed end,strands opened, flexible speedometer cable ,etc) and you'll see what comes out; everytime it sits empty,it will rust; (it's illegal and dangerous to replace it with a rubber line,never do that in a gas boat).
Mine is doing the same thing
@@josepeixoto3384 i
Just ordered a kit and float for my 1389-8490 Mercarb , tried to call but couldn't get anyone . just hope it's the right kit . Already bought one at my local dealer and it was the wrong kit .
I compared the photo of it to mine that is half way torn down and it looks the same , so I hope so .
How do I order parts from you
Please go here: www.carburetor-parts.com/mercarb-carburetor-parts
Where can I get the carb. Kit at
amazon....ebay
Great thanks!