Crown Vic WAP Block Swap, Boost Prep, Twin Turbo Crown Vic Budget Build

We got our "new" engine, tear it down, file the rings and get it back together awaiting the next phase of the build. We found that the slush box transmission must have been slipping on the dyno, either that or someone swapped out the atf with bbq sauce. That explains a few things.... So I will fix that by giving it the appropriate amount of pedals and swapping in a 5 speed (T45), and will plan on updating that with a tkx when that trans decides it hates us (1 day).
EP-1 • Ep-1, Twin Turbo P71 C...
EP-2 • Ep 2, Twin Turbo P71 C...
EP-3 • Ep 2, Twin Turbo P71 C...
EP-4 • Ep 4, Twin Turbo P71 C...
EP-5 • Ep 5, Twin Turbo P71 C...
EP-6 • Ep 6, Twin Turbo P71 C...
EP-7 • Ep 7, Twin Turbo P71 C...
EP-8 • Ep 8, POS Wastegates, ...
EP-9 • Ep 9, First Start, Blo...
EP-10A • Ep 10A Oil System Scav...
EP-10B • Ep 10B Dyno Tuning a T...
Full Build in 19 Min • Twin Turbo 2010 Crown ...
PARTS USED SO FAR.... (Using these links helps support the channel)
Turbo kit used (qty 2)---amzn.to/3CzrXqb
Exhaust hangers---amzn.to/34xgoTW
Mandrel Bend 2.25"---amzn.to/3Iac2A2
2" Turbo Ducting (between the turbos)---amzn.to/3CGuaR1
90* 3" elbow (will be replaced w/ 45* boot) amzn.to/3Je50LV
T3-T4 Turbo exhaust flange (input) amzn.to/3JfPK17
Deatschwerks 60 lb injectors EV14---deatschwerks.c...
NGK TR7IX Spark plugs---amzn.to/3JlGg4h
Coils (ACDelco)---amzn.to/3KUUQQU
Coils (MSD that one went bad in 5k)---amzn.to/3Jo3KWu
Rubber coated zip ties 12" ---amzn.to/3qng2XA
Rubber coated zip ties 8" ---amzn.to/3Is3kNF
TurboWerx Base Model Spartan High-Temperature Electric Oil Scavenge Pump ---amzn.to/3qpLULj
Fiberglass exhaust wrap, qty 2 rolls ---amzn.to/3wpPeK9
POR 15 exhaust paint ---amzn.to/36lNFlQ
45* 3" Turbo boot ---amzn.to/3It1HPU
mass airflow intake tube ---amzn.to/3D284s0
Aeromotive 340 fuel pump (almost a direct fit) ---amzn.to/3L1YjwR
mini fuse tap --amzn.to/3ugHveT
wastegates EMUSA, 38mm ---amzn.to/3K0U4S8
TurboSmart "Boost T" wastegate controler ---amzn.to/3qSu57W
Fuel Filter -6an ---amzn.to/3J5anMs
5/16 to -6an adapters (x2) ---amzn.to/3J4G5cW
-6an female to -6an female adapters (x2) ---amzn.to/3K58WPj
3/8 x 3/8 x 1/4 tee (I had to make one differently) ---amzn.to/36QJ9MA
Water methane injection ---amzn.to/3umCrqC
Oil System Fittings listed below (I used JP fittings, however these are equivalent and more available)
RETURN LINES
*This kit comes w/ all the fittings and 20' hose needed EXCEPT additional needed fittings listed below amzn.to/3JyTxqo
8an 180 (turbo's) qty 2 ---amzn.to/3wpSfdJ
*8an to 1/4" NPT (oil pan) ---amzn.to/3Iv2Beq
*8an to 3/8" NPT (scavenge pump) qty 2 ---amzn.to/3JvoPhW
SUPPLY LINES
*1/4 Brake hardline roll ---amzn.to/3JwGuFT
*1/4 to 1/8 npt compression fitting (turbo side) qty 2---amzn.to/3D6ZEjh
*1/4 to 1/4 npt compression fitting (engine side) ---amzn.to/3Jtakv6
WAP Block Swap Parts
Side Bolts (9mm WAP Block) amzn.to/3FeOXw3
Oil Pan amzn.to/38InbvQ
Gasket Set (missing oil pan, rear main, and front balancer seals) amzn.to/3OTVcde
Timing set with oil pump and incorrect water pump amzn.to/37b1HY1
Oil Pan Gasket amzn.to/3KyBb8N
High Volume Oil Pump amzn.to/3LGIqNc
Stainless Exhaust Manifold Bolts amzn.to/3OUlJqF
Head Bolts (2 sets req) amzn.to/3OTLVly
Rear Main Seal with Sleeve for install amzn.to/38KYBue
SPECIALTY TOOLS USED SO FAR....
EP 1 -Dewalt Rod Cutter (all thread technically)---amzn.to/3Kzx50l
EP 1-5 -Exhaust cutter---amzn.to/3CFr0ge
EP 2? -Body saw for curving insert cuts---amzn.to/3wap8Ld
EP 5 -Tap for oil pan -amzn.to/3Jvjd7k
EP 8 -Valve spring compressor use on wastegate -amzn.to/3wWufis
REFERENCE VIDEOS---
Exhaust Expander How To Video--- • Exhaust Pipe Expander ...
#twinturbo #p71 #policecar #hotrodanything #blownengine #dynotuning #thrownrods