When it starts lifting, all the commands freeze,the overriding key on that machine needs a clear mind to find, it sits righ next to the chair on the left hand side. No way you can use it in few seconds
@@benjaminsagauif its in an overload situation the 2540 freezes things which would have a negative impact, however you could still retract the boom for example which would make things less worse in such a case. The first mistake however was done by not using the supports, the machine goes up the full height without them but it's pretty unstable and not recommended to do that. A blown tire would be enough without the supports to tip it over, even if you did everything right.
@@simonm1447 you Can retract the boom, but with a delay of 5 seconds minimum, de-aggravating movements override the freeze, but with a delay of 5-8 sec. If you find the override button/key , it does it instantly. The fact he did not use the support legs it’s a rookie mistake,or one of overconfidence. Nevertheless a costly mistake...
@@benjaminsagau it depends on the generation of the MRT. The privilege generation has no delay, the newer privilege+ (from around 2017 on) has some delay.
I tell you what you can use though is the outriggers, he would have had to press overide to get the boom that far out without the riggers with weight on, delighted this happened without anybody getting killed as it gets another dangerous operator off the sites @benjaminsagau
Retract and lower boom could have saved this machine. Some brains freeze in the heat of the moment. It's also obvious the machine isn't big enough for the work being performed.
It actually is, they have massive outriggers on there's the boom can go almost vertical and can be used as a crane. The only telehandler with a rotating table like a crain they also have remote control.
Well people,,, new machines have a lockout function,,,,when boom is overloaded so the operator would have not been able to retract or drop the boom in emergency without depressing a special button,,, its a daft system cause if it wasn't for that function this would not have happened,, so maybe if the designers were machine operators themselves than that lockout system would be better
The 2540 does not lower the boom any more in an overload situation, but it does things which are positive in this case like retracting the boom. The first mistake was made by not using the supports, which gives you far, far more stability if you go up that high.
Man could have recovered but probably had no clue how to operate it correctly
When it starts lifting, all the commands freeze,the overriding key on that machine needs a clear mind to find, it sits righ next to the chair on the left hand side. No way you can use it in few seconds
@@benjaminsagauif its in an overload situation the 2540 freezes things which would have a negative impact, however you could still retract the boom for example which would make things less worse in such a case.
The first mistake however was done by not using the supports, the machine goes up the full height without them but it's pretty unstable and not recommended to do that. A blown tire would be enough without the supports to tip it over, even if you did everything right.
@@simonm1447 you Can retract the boom, but with a delay of 5 seconds minimum, de-aggravating movements override the freeze, but with a delay of 5-8 sec.
If you find the override button/key , it does it instantly.
The fact he did not use the support legs it’s a rookie mistake,or one of overconfidence.
Nevertheless a costly mistake...
@@benjaminsagau it depends on the generation of the MRT. The privilege generation has no delay, the newer privilege+ (from around 2017 on) has some delay.
I tell you what you can use though is the outriggers, he would have had to press overide to get the boom that far out without the riggers with weight on, delighted this happened without anybody getting killed as it gets another dangerous operator off the sites @benjaminsagau
Someone didn't read the owners manual
VgfhYDJYGVJTHUH JBBLLLIYTQ1248O0
Stabilizers are tucked away nicely
Nice n tidy like
Everybody is saying retract the boom but nobody is saying anything about reversing the machine
Boss: can you drive this
Me: i have a ticket for it
I seen this coming
Should retract the boom
This almost happened to me with the skid steer
At least the excape rope deployed...LOL
UA-cam certified operator
BOOM DOWN!
nice to see those stabilizer legs were tucked in all the way , that will have saved them getting damaged ,,, rtfm.
Retract and lower boom could have saved this machine. Some brains freeze in the heat of the moment. It's also obvious the machine isn't big enough for the work being performed.
It actually is, they have massive outriggers on there's the boom can go almost vertical and can be used as a crane. The only telehandler with a rotating table like a crain they also have remote control.
How about reversing and shifting the center of gravity. Its just like riding a wheelie or a stoppie
Where did he get his license to operate that lift?
Out of a Crackerjack Box ?
I couldn't easily saved that. The stuff I've done with forklifts and cranes have been astounding in the past.
Can someone please bring another forklift so we can lift this one back up?
So much for certificates
Bon bah là
Aucun stabilisateurs + shunt de la sécurité
Aucun reflex du pilote
=Perfect 👌🏽
Geriye doğru sallanırken bomu aşağı doğru indirseydi kurtarabilirdi ben de aynı mesleği yapıyorum
This happened because he never had his tongue out
Looks like he didn't have his feet out 🙄
Surely it has some kind off stabilisers
They called it a jay lift so i said no i can use a sizzor ITS THE SAME i didnt get job over a name and this fool has one.
c'est comme ça quand on ne met pas les stabilisateurs. 👎😡😡🇨🇵🇨🇵👋
Bro who made that telehandler so long?
Well people,,, new machines have a lockout function,,,,when boom is overloaded so the operator would have not been able to retract or drop the boom in emergency without depressing a special button,,, its a daft system cause if it wasn't for that function this would not have happened,, so maybe if the designers were machine operators themselves than that lockout system would be better
The 2540 does not lower the boom any more in an overload situation, but it does things which are positive in this case like retracting the boom.
The first mistake was made by not using the supports, which gives you far, far more stability if you go up that high.
Fired?
Bet he filled his pants that day 😂😂😂
Widać że fachowiec !!!
Ben bu makinayı yıllarca kullandım eğer orda olsaydım o makinayı devrilmeden indirirdim malesef işi bilmeyenler var
It might have worked if he would have dropped the forks
He should’ve lowered the boom
supports of the forklift are not in use
Petit chauffeur 🇨🇵✌️
dangereux surtout. incapable inconscients ☹☹😡🛑
An amateur does this,first day at work, the legs are not lowered to stabilize it😁
And THAT kids, is how a pendulum works........
It's usually other way around, but it's the same principle.
It is not video game it is real life please backup to real life 😂
Кто в здравом уме ездит с таким вылетом стрелы ?
Subio el bun sin ante bajar las patas de seguridad 😅
It was my first day! Gimme a break 😂
Gran parte culpa del operador pero digo q en ese aspecto si el equipo no se bloqueará el operador pudiera salvar el equipo antes de que se volte
Oooh, sooo close...
How the fuck do you even start there. 100 chances to save himself from this outcome before the video even started.
si seulement il avait baissé le bras, la connerie aurait été peut-être éviter 😧😧🇨🇵
Always have to pay for an education
First you say it then you do it. Oh shit
Just retract boom
O bomu önü doğru atsana devrilmeyecekti ama kaza işte oldumu oluyor bir anlık. Göze perdeliyor
Do not pass GO do not collect £200
Keşke yavaşça aşağı indirip bom toplasaydın
Manituuuuu
Tombé un instant dans les pommes le temps de se ressaisir trop tard
Napewno przeszedł kurs bespieczenstwa
Ale bluzę odblaskowa ma:)
No reflex !!!
Оператор не опытный😁 в штаны наложил и надеется что пронесет
Merci les sécurité à la c..,
qui on empêche le gars de baisser le flèche
Ohne Reaktion der Typ 😂
Hätte man locker noch retten können, als er nach hinten kippt arm nach vorne bzw arm einfahren 🙈
Super 💕
Bajas la pluma y lo evitas
well. at least most of ut landed flat xD im sure the forked end is fnna b a lil fukd up tho
Nasıl becere bildin onu göz göre gore
Who flung dung?
Nguy hiểm nhất thế giới
There is a load chart in front of the steering wheel. As important as the Bible. Use it
Why you don’t know how to read it
La faute au conducteur
🤦♂️ einmal mit Profis ...
Involontaire peut être !
Eu doido pra operar uma dessas e ele faz isso kkk aqui no Brasil em São luiz do Maranhão tem duas na ária da Vale ou é uma
Hiç birşeyi olmaz. Sonuç bom.
круто
auslander😅
Sem talento
Un accident
😖
Holi crap
😂😂😂😂😂
Gg
ㅉㅉㅉ 발안피냐
👎🏻👎🏻👎🏻👎🏻
👍🏻👍🏻👍🏻👍🏻
Boom forward ninny
It not a surprise how stupid operators are over their head
Muy bien el fenómeno poco sentido del conocimiento
Looking for a New job , Stay on the Ground..lol
Glück gehabt
If he put the machine into first gear and hit the throttle just a little that wouldn't of happened 🤦♂️
😎👍🤭🤪
Merci les sécurité à la c..,
qui on empêche le gars de baisser le flèche
Merci les sécurité à la c..,
qui on empêche le gars de baisser le flèche