Thank you very much for this tutorial, I managed to repair my CT-200 even if the screw under the motor was difficult to access. A very good pioneer hi-fi system to top it off
Can confirm that this works on the CT-520 as well. A bit tricky with a solenoid in the way however. Great video, wish I'd found this video before taking all of the front of mine though...
Did it just at the moment ! Just waiting to get some tapes. Do you know how to lubrificate the two black heads that allow the tape to turn ? When I pull on play without tape it IS hardly turning. Thanks a lot !
Vous pouvez trouver en cherchant des courroies compatibles sur Internet sinon voici les dimensions : (j'ai pas converti mais voilà) FRW8.0 Flat Belt, Small Inside Circumference: 8.0 inch Width: 3mm Thickness: 0.6mm Scx4.3 Square Belt, Small Inside Diameter: 4.3 inches Thickness 1.0mm Scy8.0 Square Belt, Extra Small Inside Diameter: 65mm Thickness 0.8mm Square Section Belt 65 x 0.8mm
I have the ct 200 and ct 300 it s the same machine change all belts but if you don t put the right belt in the counter Play just for 5 seconds them stops ...
Thank you very much for this tutorial, I managed to repair my CT-200 even if the screw under the motor was difficult to access. A very good pioneer hi-fi system to top it off
Can confirm that this works on the CT-520 as well. A bit tricky with a solenoid in the way however. Great video, wish I'd found this video before taking all of the front of mine though...
Thank you ! 👍😊
Great job man. Have a CT F550 and am going to attempt belt replacement.
Thank you so much for sharing this video 🙂👌
Отличная работа, отличная дека!👍 У меня большая коллекция дек и на многих пришлось менять пассики и шестерёнки. Видео тоже есть!)
Thank you 😊
Did it just at the moment ! Just waiting to get some tapes. Do you know how to lubrificate the two black heads that allow the tape to turn ? When I pull on play without tape it IS hardly turning.
Thanks a lot !
Is the big wheel inside spinning as it should? I'm not really sure about lubrication here, but if anything, i think some PTFE lubricant.
Hi! Great job! I want to fix mine also. Where can I buy the belt?
FRW8.0
Flat Belt, Small
Inside Circumference: 8.0 inch
Width: 3mm
Thickness: 0.6mm
Scx4.3
Square Belt, Small
Inside Diameter: 4.3 inches
Thickness 1.0mm
Scy8.0
Square Belt, Extra Small
Inside Diameter: 65mm
Thickness 0.8mm
Square Section Belt 65 x 0.8mm
Merci pour la vidéo. Pouvez-vous nous donner la dimension des courroies, ça nous évitera de faire la manipulation pour avoir les cotes. Merci
Vous pouvez trouver en cherchant des courroies compatibles sur Internet sinon voici les dimensions : (j'ai pas converti mais voilà)
FRW8.0
Flat Belt, Small
Inside Circumference: 8.0 inch
Width: 3mm
Thickness: 0.6mm
Scx4.3
Square Belt, Small
Inside Diameter: 4.3 inches
Thickness 1.0mm
Scy8.0
Square Belt, Extra Small
Inside Diameter: 65mm
Thickness 0.8mm
Square Section Belt 65 x 0.8mm
As lost as I was when I realized the belt was bad.
Grande maestro. Questo si che è un video utile
Thank you 👍😊
0:28 0:29 0:30 0:32 0:36 0:37
I have the ct 200 and ct 300 it s the same machine change all belts but if you don t put the right belt in the counter
Play just for 5 seconds them stops ...
thanks for creating this :0)
Thank you for watching 🤗
good work
Thank you. Learning by doing 😄
Does anyone know the belt sizes?
Thanks
Ps Looks same as CT400 model
FRW8.0
Flat Belt, Small
Inside Circumference: 8.0 inch
Width: 3mm
Thickness: 0.6mm
Scx4.3
Square Belt, Small
Inside Diameter: 4.3 inches
Thickness 1.0mm
Scy8.0
Square Belt, Extra Small
Inside Diameter: 65mm
Thickness 0.8mm
Square Section Belt 65 x 0.8mm