I realize this is an older video, but its just what I've been looking for. I gotta 2009 caliber sxt needing the rear subframe replaced and it looks like a heck of a job. You gave me some really good tips on disassembly and I appreciate it immensely. Didnt see anywhere on how long it took you to complete the job. Guessing at least 1 solid day. Thanks again for a great video.
your not alone. my 2007 needs the rear replaced and im gonna do it this weekend, id recommend lots of PB or WD40 before hand. and a breaker bar. the caliber its a great commute car tbh just needs proper care
Fixing these rust issues is not for the faint of heart. So many of the younger generation would not have the physical strength to tackle this project. The one thing I would add is before you jack the car put a tarp down on the grass. It makes finding dropped hardware and tools much easier to find.
@@timkeiper8588 I just replaced the lower arms 2 months ago, now the upper arms messed up and my subframe cracked... it just cost me 1000 to repair on Thanksgiving
@@timkeiper8588 I am in the same boat. Looks like previous owner got into anaccident which case the lower control arm to bust out of the subframe and split along the edge. It was very poorly fixed with large washers welded on.
Can you or anybody tell me a good place I can get a subframe and how do I know if it’s good quality or not? I’m seeing a lot of different prices, what would the difference be?
The rear frame I bought used from Stoystown Auto parts in Pennsylvania. The front I ordered online. It was less expensive online and it was new. It can be more difficult chosing the correct part with so many options online. Do your due diligence to get the one for your specific vehicle. Make sure it has the hardware and get it online.
I imagine hes got a screw extracter set on hand. I ripped the subframe out of my old compass to put on my newer one. Previous owner got into an accident and it mangled the subframe making alignment impossible. I broke one bolt removing the subframe o when i go to the swap I will have a screw=extractor set on hand in case. You drill a hole into the broken bolt and the extractor will grip inside that hole and you can reverse it out.
Curious how you got the two broken subframe bolts out. I'm in the middle of this job right now and am having a hard time removing the two broken bolts.
@@cnubz1107 I am 3 months late to give you advice on this, but just in case someone comes along with a similar problem I'll give my 2 cents. The easiest and most surefire method is to just weld a nut onto them if you can weld and its not broken off down under the surface. Otherwise get some pb blaster or similar lubricant down into the threads and let it soak and reapply as much as you have patience for, then drill a hole into the bolt shaft and get as big of a bolt extractor bit into the hole as far as possible then start cranking "lefty loosey", and pray the bolt breaks loose before the extractor breaks off. you could also try heating the area around the bolt with a torch, it might expand enough to break lose from the bolt, or at least relieve a little pressure while you're cranking on that extractor bit
@@briarg1485 That 2wd looks like the same subframe as my 4wd. But as Tim said, replacement is a lot more work on the 4wd. BTW, some torque specs would be helpful here.
I am in the middle of changing out the rear sub frame for a 2010 Jeep Patriot Limited 4wd and NO it is not easy. Mine has severe rust and most of the bolts take a lot of TLC to get them off/out without breaking them. I am down to one major task now, getting the left rear CV shaft out of the hub. This CV shaft is seriously stuck. I have now tried tow different tools designed to push the shaft out of the hub with no luck at all. It appears that I will have to remove the hub/bearing assembly with the CV shat and use a hydraulic press to remove the shaft. I have three (3) of the four (4) bolt that hold the sub-frame to the uni-body loose but one of them is giving me a fit not wanting to break loose. I drilled a 1/4" hole in the outer side of the uni-body so I can spray PB Blaster into the channel of the uni-body hoping the penetrating fluid will get to the top of the bolt and help. I know that the nut for this bolt is spot welded to the channel piece of the uni-body and I don't want to break the but loose either. I cannot get the bolts that hold the transmission to the sub-frame to loosen up either. Hopefully I can get this sub-frame and tranny out together onto the shop floor and see a better way to loosen these tranny mounting bolts.
I did this same job on a customers car and 2 of the bolts broke on me also i spray the bolts with penetrating oil there was so much rust on everything that the penetrating oil did not do anything I used a torch thinking it would help but it did not so after the bolts broke off I was able to heat the area around the stud that was left and with a vice grip I was able to remove both bolts and we order new bolts and replaced them. It was a free job I work at a shop that had a girl working there and the car came in with a grinding noise from the rear the girl told them it was the brakes that was making the noise the customer say ok do it she change the brakes and the noise was still there she went crazy trying to find the noise was not able to find the noise so the manager told me to go find the noise and it turns out the noise was coming from the rear sub frame being broken the replacement sub frame cost $300 because the brakes was missed diagnose the customer got free brakes and a free alignment and free subframe and free Labor the customer got there car back with all new parts everything fix and paid $0 out of pocket the shop took the hit.
Excellent video, straight-to-the-point with good tips and not a bunch of unnecessary BS fluff, thank you brother
I realize this is an older video, but its just what I've been looking for. I gotta 2009 caliber sxt needing the rear subframe replaced and it looks like a heck of a job. You gave me some really good tips on disassembly and I appreciate it immensely. Didnt see anywhere on how long it took you to complete the job. Guessing at least 1 solid day. Thanks again for a great video.
your not alone. my 2007 needs the rear replaced and im gonna do it this weekend, id recommend lots of PB or WD40 before hand. and a breaker bar. the caliber its a great commute car tbh just needs proper care
Have now changed my rear subframe. Thank you for your video.
Håkan Magnusson Halmstad Sweden.
Right to the point.Easy to understand.Appreciate your knowledge. Thanks!
Love your clear explanation of each step. I'm sorry I broke your car 😉 great video as always ♥️
Thanks for this video, it was what I was looking for, how to disassemble it, you gave me many ideas right now, thank you very much for the video.🙏
Fixing these rust issues is not for the faint of heart. So many of the younger generation would not have the physical strength to tackle this project. The one thing I would add is before you jack the car put a tarp down on the grass. It makes finding dropped hardware and tools much easier to find.
Good tips and thanks for taking the time to video and share.
Pre-soak bolts that you are intending to remove with wd40 or something similar to make work easier.
Very funny Guy 😂 "unless your iron counts low keep your mouth shut"
Nice job brother and great information!!!
Buen vídeo rey, fue bastante útil.
Great video. Thank you, I'm going to be doing this, this weekend.
Mine rusted so bad the lower control arm broke right out of the frame and hit the ground. Luckily we were in a parking lot, not out on the road.
@@timkeiper8588 I just replaced the lower arms 2 months ago, now the upper arms messed up and my subframe cracked... it just cost me 1000 to repair on Thanksgiving
@@timkeiper8588 I am in the same boat. Looks like previous owner got into anaccident which case the lower control arm to bust out of the subframe and split along the edge. It was very poorly fixed with large washers welded on.
Great video very helpful
Thanks
Ok.this man needs a hoist. 🤣 Christmas?
Ur the man thank you
Thanks pope is a good video
new parts from dealer are dirt cheap : rear 2wd crossmember CBLTN366ab=90$ bolt kit rear CBLTN364AA = 5$
Realy need 2007 jeep patriot subfraim replaced!!
How do get the broken bolts out
thank for the video!
What is the part called that goes into that large round hole?
Good job! 👍
Good job 👍
no sway bar?
How did you get the busted bolts off?
I'd like to know about how long this took to get the subframe replaced in total.
Took me 2 days total working at easy the exhaust was the toughest part by myself I cut in 2 places to make it easier for me.
Can you or anybody tell me a good place I can get a subframe and how do I know if it’s good quality or not? I’m seeing a lot of different prices, what would the difference be?
The rear frame I bought used from Stoystown Auto parts in Pennsylvania. The front I ordered online. It was less expensive online and it was new. It can be more difficult chosing the correct part with so many options online. Do your due diligence to get the one for your specific vehicle. Make sure it has the hardware and get it online.
You said you broke two bolts outta four for the subframe. How did you remove the broken bolts
I imagine hes got a screw extracter set on hand. I ripped the subframe out of my old compass to put on my newer one. Previous owner got into an accident and it mangled the subframe making alignment impossible. I broke one bolt removing the subframe o when i go to the swap I will have a screw=extractor set on hand in case. You drill a hole into the broken bolt and the extractor will grip inside that hole and you can reverse it out.
Curious how you got the two broken subframe bolts out. I'm in the middle of this job right now and am having a hard time removing the two broken bolts.
I got lucky they broke off with enough room to get a pipe wrench on them.
@Viral Workaholic what if you can't get a pipe wrench on them?
@@cnubz1107 I am 3 months late to give you advice on this, but just in case someone comes along with a similar problem I'll give my 2 cents. The easiest and most surefire method is to just weld a nut onto them if you can weld and its not broken off down under the surface. Otherwise get some pb blaster or similar lubricant down into the threads and let it soak and reapply as much as you have patience for, then drill a hole into the bolt shaft and get as big of a bolt extractor bit into the hole as far as possible then start cranking "lefty loosey", and pray the bolt breaks loose before the extractor breaks off. you could also try heating the area around the bolt with a torch, it might expand enough to break lose from the bolt, or at least relieve a little pressure while you're cranking on that extractor bit
How long did it take to change out?
Good video. BUT the four wheel model is NOT as easy to change, and especially with Northeastern PA rust.
This weekend I'm going after brakes and the wheel bearing on one side.
@@viralworkaholic6766 where did you find the part for this? I can only find rear crossmember for the 4 wheel drive...
@@briarg1485 That 2wd looks like the same subframe as my 4wd. But as Tim said, replacement is a lot more work on the 4wd. BTW, some torque specs would be helpful here.
I am in the middle of changing out the rear sub frame for a 2010 Jeep Patriot Limited 4wd and NO it is not easy. Mine has severe rust and most of the bolts take a lot of TLC to get them off/out without breaking them. I am down to one major task now, getting the left rear CV shaft out of the hub. This CV shaft is seriously stuck. I have now tried tow different tools designed to push the shaft out of the hub with no luck at all. It appears that I will have to remove the hub/bearing assembly with the CV shat and use a hydraulic press to remove the shaft. I have three (3) of the four (4) bolt that hold the sub-frame to the uni-body loose but one of them is giving me a fit not wanting to break loose. I drilled a 1/4" hole in the outer side of the uni-body so I can spray PB Blaster into the channel of the uni-body hoping the penetrating fluid will get to the top of the bolt and help. I know that the nut for this bolt is spot welded to the channel piece of the uni-body and I don't want to break the but loose either. I cannot get the bolts that hold the transmission to the sub-frame to loosen up either. Hopefully I can get this sub-frame and tranny out together onto the shop floor and see a better way to loosen these tranny mounting bolts.
What drill do you use
How did it drive after you left the broken bolts in?
I’m curious too??
I did this same job on a customers car and 2 of the bolts broke on me also i spray the bolts with penetrating oil there was so much rust on everything that the penetrating oil did not do anything I used a torch thinking it would help but it did not so after the bolts broke off I was able to heat the area around the stud that was left and with a vice grip I was able to remove both bolts and we order new bolts and replaced them.
It was a free job I work at a shop that had a girl working there and the car came in with a grinding noise from the rear the girl told them it was the brakes that was making the noise the customer say ok do it she change the brakes and the noise was still there she went crazy trying to find the noise was not able to find the noise so the manager told me to go find the noise and it turns out the noise was coming from the rear sub frame being broken the replacement sub frame cost $300 because the brakes was missed diagnose the customer got free brakes and a free alignment and free subframe and free Labor the customer got there car back with all new parts everything fix and paid $0 out of pocket the shop took the hit.
Yeah That One Was Easy Beacause That Jeep Not A (4×4) The Other's Jeep's Compass 4×4 is More Hard To Do it,🙄
125? eBay got them for 170...
WTF was Dodge/Chrysler/Jeep/Eagle thinking?
Good job on piece of shit car ,I have the same shits 😁😁😁
God damn how rusty