Thank you for this video. What helped me the most is the section starting at 7:00 for failsafe settings. This is a critical item to the setup. If you have time, I would recommend breaking this section out and into a it's own video. Thank you.
Thanks Ali! Everything works perfectly! I even turned off my receiver! The failsafe kicked in, the the Quad rose to about 30 meters, floated toward me, waited for 15 secs,.. landed and shut down! Awesome! The only thing is that you have to reboot the Naza (disconnect and reconnect battery) after failsafe is activated. Otherwise it will not arm from the transmitter.
thaks ali for this great great great tutorial.......u are the best and kindness person....... with this vid i can solve the problem setting with my radio...... hope you will be successful in your businnes ....
Ali- Thanks for posting this video! I just got a Futaba 8FG Super & this will help me with setting-up the radio. Any way of posting a video on setting up the S-Bus with the Naza?
First, I'd like to say thank you and great 3 part tutorial. When you say export the settings where do you export them to? Do you just click export and they are saved. If you need them again where do I find them? This video is so good I can always come back and watch again. Thanks again. (Tom)
Hi. Thanks for a great 3 part video.. I went and brought the Futaba T8J based on your videos. Great radio and your videos really helped me get it setup with no fuss what so ever.
Thanks for the walk through Ali! I've got everything working except the control mode selection. My Naza M Lite assistant shows the 'manual' selection disabled and moving the switch positions of switch C & G (my T8J has 2 3 position switches which are C & G, not C & E) does not move the mode slider from Atti to any other switch mode. Not sure what I'm doing wrong. So here's my setup: Futaba T8J TX Aux-Chan setup: Ch5 = SwC Ch6 = VR Ch7 = SwG Ch 8 = DT6 Futaba R2008SB RX DJI Naza M Lite with GPS Channels 1-4 from RX to Naza A,E,T,R in order Channel 5 from RX to Channel U Channel 6 from RX to Channel X1 Channel 7 from RX to Channel X2 V-SEN wired to distribution wafer & plugged into port X3 DJI e310 motor & esc combo pack (4 motors) Multistar 8000mAh 14.8v battery AND... a quad of my own design: www.thingiverse.com/thing:1513237 (ignore the orientation, its upside down) Naza Assistant 1.0 Stick calibration = good Voltage monitor = good (set for 4s) Control Mode Switch = *** Stuck in "Atti." *** (manual dropdown box disabled) I've walked through all 3 videos in this series several times. Any thoughts on what I've go configured wrong?
Can you use one of the extra channels on the transmitter to control the gimbal wile the naza is still holding the gimbals position. Say use the channel 5 nob to control the pitch?
Hi, Figured out my own issues. Listened more carefully. Everything working except on Futaba 7c apparently failsafe only works thru channel 3 (throttle). I don't want to go through the crazy mixing solution that I have seen so will have to be careful. Wish I could bind my Phantom controller to the Flame Wheel. lol Have not seen Rx available to do that. Take care! Thanks for your efforts!!
Well I was thinking of buying the dji phantom but u said it won't handle strong wind like 20mph but I already have a nice 450size quadcopter so I was thinking of maybe buying just the naza & GPS an also change the esc anise it on my dx6i so if I use my own quadcopter it will handle the wind better the the dji phantom in high wind like 20mph???
Fantastic video alishanmao. Congratulations. Its very easy to understand, but.... My transmiter is a FS-TH9x and I'm not able to find how can I configure it to use the switches. Any sugestion? Thanks for your videos
Dear Alishanmao. I'm a huge fan and i love your videos. I have a futaba 7c 2,4ghz. I have a problem with setting up the fail safe because i am only able to set failsafe on ch 3 and not the ch 5:ger to activate the failsafe when the remote is off. Hope you can help me :-)
could u please make a video of what setting u need to adjust on ur radio and u receiver if i was just flying a basic quadcopter with kk.2 board???... i had a range problem with my radio and lost a quad....
Hi, Great videos. Something I am not quite grasping. Using a Futaba 7c For intelligent control mode, I have adjusted my channel 5 endpoint so it is in the Fail-safe (blue) area. Then when I disconnect and activate my mode switch I go between fail-safe to Att to failsafe. (rapid orange flashing). I have done a write each time. Also when I click on (3) Int. Or. Control, it instantly turns back off. Thanks!!
Hello alishanmao, I have ordered a new DJI Naza system, do I need to change something on the computer when I want to fly in X mode? And also changing something on the transmitter? Or just setup on airplane mode and its done?:)
Thanks for nice video. I have futaba T6J. There is no 3 position switch. How should i configure control mode switch ? I would like to use all modes: manual , GPS and Altitude. Is the only possible way is to use pot control ? Thanks for any advice...
Nice video Ali, very helpful. I am using the Futaba T6XA and the only problem I have is that I cant bring channel 5 to Atti mode no matter what I do with ATV and SubTrims. Just wont go to Atti mode with the Channel 5 switch thrown in. Somehow using the Channel 6 knob to get into Atti mode. But that could be tricky. In every other way the T6XA seems to work OK. Any suggestions ? I need to bring ATV below 10 % and T6 doesnt do that. It goes from 10 to 120 %
awesome video! so i have a quesion, does the battery connect to the naza v2, and the naza connect to the esc? or does the battery connect to esc and naza? I am very confused about esc, naza, and reciever connections. please help. i am using opto esc.
Thanks again for the very informational video. I'm using a Devo 10 radio and I'm using aux3(RUDD D/R) as a separate switch for failsafe. When setting failsafe on throttle do I put L 54% or H 54%? I'm not sure why there is a L or H.
Thank you, well done. Love your help and ENTHUSIASM ! Could you do it with the DX8 too :( If it is as easy as you made it look, I'm placing my order this week. Done ! Have had the KK2.0. worked well. NOW having so many issues and problems i don't know where to start. I think i just decided I'm starting with a new FC. Nazza's looking good. :)
And if sacrifice manual for failsafe, I should always have throttle around 50% before switching the switch, and if I want to regain control, make sure my throttle is around 50%? Is there anyways to mix the switches so I can use a separate switch to activate failsafe without sacrificing manual? more specifically on Devo 8 radio.. thanks!!!
OMG! I would be lost without you Alishanmao so I subscribed, clicked your ads, and clicked like. Im new to this Naza bizzo and it has been quite bewildering but your tutorials saved me. I have a Devo 8S with a Rx802, what should I select.. traditional, D-bus or PPM????? Googled it to death to no avail.
Hi Ali,,,,I have follow your steps on this video and everything is ok,,,,,,when I reconnect back the drone it gives me a fast blinking red and i have the switch to the middle when I power up the tx and drone,,can u help..
Putting together a new mount for the keychain #808 camera. Even with the props perfectly balanced, I get too much "Jello" effect with video playback. I need something to dampen the vibration.
Hi Ali,,,When I first time connect as per your video exacctly,,,there is a beeping sound coming from the motor or the esc just cannot distinguish which one,,,,can you help on this tq
Hi I am from India Thanks for this Video I have a f450 and I use dji Naza m light and flysky i6 transmitter When I switch off my transmitter than my drone don't come back home position Please help me please I am Big fan of yours
Do you really need to set the fail safe throttle to 55% ??? I use Futaba 7cap, set the fail safe without taking care of setting the throttle, & it does a good job, when i switch the power off, it gets to 60ft high & comes back to its departure point....
Hey Ali, thanks for the tutorial video! I have set my failsafe so when I turn off radio, the slider goes to "failsafe", but the throttle at "holding", it returned home and landed without a problem. So I assume thats the same as you setting the throttle at 55% since when I'm up in the sky, the throttle is almost always around 50%. Or should I set it to 55% manually just in case somehow I'm not in that throttle range?
I want to built FPV quadcopter but I need only DJI Naza M V2 . Please help me I am in big confusion that can we setup Any other Vtx video camera transmitter to DJI Control board ?
i entered zeros configuring the gps and it was fine. i measured and entered the xyz and results were the same. wondering why have the xyz if it doesn't make any difference in gps performance.
Hi, Hope you can help. I have bought a RTF version of what you have here, DJI 450 and Futuba T8J. I have set it up in the same way as you have, but it will not power up the motors, everything else seems to work, I get a green light on the R2008SB receiver, but the DJI receiver blinks 1 red, two orange after I bind them? it goes through a series of blinks, including several green, but then just sits there and blink red/orange and nothing works? Any ideas.
Go home works without gps? I don't understand when speak, not native speaker - please, write even if you say the same in video. What would you recommend for area, where gps signal oftentimes losts? Thank you.
I have my receiver bound but I am still unable to get the Assist software to pick up my receiver/tx Im using the 9xr and the FRsky D8R-II ... I choose PPM mode in Assistant but still not receiving any signal... motors will not arm or spin? Any ideas what I should do next? Thank you in advance!
Hi Allshanmao I tried to setup my futaba t8j by following your video but all the settings came out wrong,I am using the s-bus on the r2008sb receiver.I had to change the switch locations as follows 1 to get the gps,attitude and manual to work on switch e I had to use ch7 2 t0 get home lock etc to work on switch c I had to use ch6. 3 to get the vr knob to work I had to use ch5. I tried to use the receiver as normal without using the s-bus but the naza lite unit would not link in. I take it the f550 will still work with these settings. Regards Alan c
Ali help!? I have a Naza-M v2 I just buy from a friend. My PC is windows 8.1. I tried everything but can't even get my pc to recognize the naza when I plug the usb to the LED unit. Henceforth I can't even install the driver. When I plug in the LED just goes off does not turn solid green and my PC does not recognize it at all.. Any advice??
I bought Futaba T8J and F450 Quadcopter with Naza Lite. The DJI assist software I use is DJI NAZAM Assistant 2.20. I downloaded the drivers so my LED unit is recognized by the PC, but when I move the reemote sticks the display screen doesn't move at all!!! I don't know if I haven't downloaded enough things yet. ANYONE HAVE ANY CLUES, THANKS
ALISHANMAO I KNOW YOU USE FUTABA, AND BECAUSE OF THAT I BOUGHT IT. THE SAME ONE LIKE YOU, FUTABA 14SG Are u using naza v2? how is that possible? naza has only 8 channels. I have a retractable gear, lights, pan and tild for gopro and fpv , and i dont find the way to connect all of them together, I'm using futaba 14sg with sbus. its a f550. 1234channels are movements, 5 gps,altitutde, manual 6 curs lock , home lock 7 failsafe. 8 empty so i only have channel 8. Please help!
hi, I like to build a quadcopter with gps, but I don't know where how to start build one, so pls guide me to build one,I like to do with the quadcopter is fly it A point to B point using gps location, (and I am in india, Chennai) pls tell me where to get the parts all so. i
Hello i have a problem:i connect the battery,bind with my spectrum dx7s and then connect it to the computer with the cable that it came.I open the program but it doesn't detect it.i tried in another computer and the same results.What can i do ?
Hi There I am setting up F 450 with E310 prop drive and E 420 esc. should i calibrate those esc as well.? please reply Becouse when i flow my f450 little bit of vibrating.
I'm Just finishing up a DJI f450 build and I've run into a problem. I'm using a brand new Spektrum DX8 transmitter with AR8000 Receiver and TM1000 Telemetry Module. Everything is set-up and appears to be working properly on the assistant software... Bottom line is the motors only seem to throttle up properly when in Manual Mode... When I switch to Att or GPS Mode, throttle response is lazy and greatly reduced (can't take off!).... Any ideas??? I'm ready to take a sledge hammer to it!!! :-(
Nice video! I use a slightly different setup because of a different radio :). I have only one 3 way switch so i programmed a mixer for different switches into my radio it's quiet nice. Besides this i agree to your setup completely. People are so damn lazy! They can do it all by theirselves. JUST READ THE MANUAL OF THE TRANSMITTER AND THE NAZA! Instead they ask questions and steal your time.
when I move my switch A on my Turnigy TGY i10 fo between the left side blue box to failsafe and then to the right blue box in the slider , why dont show me Manual and GPS selected in blue
Hi. im using a Turnigy 9x and getting a CFG-ERR on dji naza assistant program. this is the error: CFG-ERR Configuration error, this may cause by firmware upgrade from old version. or abnormal Tx calibration. Re-calibrate your transmitter, and power cycle your controller and check all of the parameters. Is there someone who know what i should do?
Any idea what would cause this change? With my FW-450 with Naza-M, after setting everything up after mounting the GPS on it, throttle worked normally gradually increasing motor speed as throttle moved from low to full. But last time I flew it, after starting motors, leave throttle closed and as usual, motors would shut off after about 3 seconds, but if throttle opened, motors remained just slowly turning until throttle got to just under 1/2, then motors started speeding up but instead of lift-off just over 1/2, had to open throttle to around 3/4. Once Naza system realized quad was flying, throttle acted normally and I had to close throttle back to just over 1/2 to prevent rapid climb, but once landed at under 1/2 throttle, close throttle just 1 or 2 clicks lower and motors would suddenly slow to speed they normally turn just after starting motors and maintain that motor speed all the way from just below 1/2 to full closed stick position. Now, arming still works as usual, but I get absolutely NO motor response from throttle closed to throttle just under 1/2, then sudden motor speed change near 1/2 and smooth throttle response from just over 1/2 to full throttle.
Hi Ali I follow exactly as per your video,,but when I throttle up the bird just wont lift off,,,even with 100% throttle .......can u help Tq Assalamualaikum
Hi... My DJI Phantom work with out any problem it does communicate with the software with in no time. But, My DJI Naza m lite brand new out of the box. LED kept bring fast red. you said, it not program yet. I try to connect it to my Naza m V2 software. but it not communicate with the software. On the software bottom left show " MC Out Put" on red to white while plug the USB cable in. and the software said please connect to the controller. Can anyone help me how to fix this problem.
I purchased the naza lite with gps got it for fathers Day and still cannot fly it. I am ready to take it back for refund and purchase the ideafly at least I kn I w it will work. Thumps down from me on naza. Call the tect support he helped me with the driver but he has so many people waiting for help like me that he tells you he has to go and email him if you cannot get it to work. We'll guess what he will not respond. Hobby shop where I purchased cannot help $225.00 down the drain.
Thank you for this video. What helped me the most is the section starting at 7:00 for failsafe settings. This is a critical item to the setup. If you have time, I would recommend breaking this section out and into a it's own video. Thank you.
Thanks Ali! Everything works perfectly! I even turned off my receiver! The failsafe kicked in, the the Quad rose to about 30 meters, floated toward me, waited for 15 secs,.. landed and shut down! Awesome! The only thing is that you have to reboot the Naza (disconnect and reconnect battery) after failsafe is activated. Otherwise it will not arm from the transmitter.
thaks ali for this great great great tutorial.......u are the best and kindness person.......
with this vid i can solve the problem setting with my radio......
hope you will be successful in your businnes ....
I just programed my futaba T10J to my flame wheel F550 seam very complicated, but with your video and the step by step it was very simple,thank you :)
Ali- Thanks for posting this video! I just got a Futaba 8FG Super & this will help me with setting-up the radio.
Any way of posting a video on setting up the S-Bus with the Naza?
First, I'd like to say thank you and great 3 part tutorial. When you say export the settings where do you export them to? Do you just click export and they are saved. If you need them again where do I find them? This video is so good I can always come back and watch again. Thanks again. (Tom)
Hi. Thanks for a great 3 part video.. I went and brought the Futaba T8J based on your videos. Great radio and your videos really helped me get it setup with no fuss what so ever.
Thanks for the walk through Ali! I've got everything working except the control mode selection. My Naza M Lite assistant shows the 'manual' selection disabled and moving the switch positions of switch C & G (my T8J has 2 3 position switches which are C & G, not C & E) does not move the mode slider from Atti to any other switch mode. Not sure what I'm doing wrong.
So here's my setup:
Futaba T8J TX
Aux-Chan setup: Ch5 = SwC
Ch6 = VR
Ch7 = SwG
Ch 8 = DT6
Futaba R2008SB RX
DJI Naza M Lite with GPS
Channels 1-4 from RX to Naza A,E,T,R in order
Channel 5 from RX to Channel U
Channel 6 from RX to Channel X1
Channel 7 from RX to Channel X2
V-SEN wired to distribution wafer & plugged into port X3
DJI e310 motor & esc combo pack (4 motors)
Multistar 8000mAh 14.8v battery
AND... a quad of my own design: www.thingiverse.com/thing:1513237 (ignore the orientation, its upside down)
Naza Assistant 1.0
Stick calibration = good
Voltage monitor = good (set for 4s)
Control Mode Switch = *** Stuck in "Atti." *** (manual dropdown box disabled)
I've walked through all 3 videos in this series several times. Any thoughts on what I've go configured wrong?
Thank you . it would have taken me a month to get it right. EXCELLENT JOB!
Can you use one of the extra channels on the transmitter to control the gimbal wile the naza is still holding the gimbals position. Say use the channel 5 nob to control the pitch?
Hi, Figured out my own issues. Listened more carefully. Everything working except on Futaba 7c apparently failsafe only works thru channel 3 (throttle). I don't want to go through the crazy mixing solution that I have seen so will have to be careful. Wish I could bind my Phantom controller to the Flame Wheel. lol Have not seen Rx available to do that. Take care! Thanks for your efforts!!
have you made a video with flysky radio with naza v2
Well I was thinking of buying the dji phantom but u said it won't handle strong wind like 20mph but I already have a nice 450size quadcopter so I was thinking of maybe buying just the naza & GPS an also change the esc anise it on my dx6i so if I use my own quadcopter it will handle the wind better the the dji phantom in high wind like 20mph???
Mr Ali u did a good job Thanks man I hope u keep making nice video like this again
Fantastic video alishanmao. Congratulations. Its very easy to understand, but....
My transmiter is a FS-TH9x and I'm not able to find how can I configure it to use the switches. Any sugestion?
Thanks for your videos
How good are the supplied sticky pads for the GPS mounting? how much do you trust them mate?
Great videos mate,
Brian :)
Hi... your video help very well ... thanks for that, but I have a question: Can I control the Naza control with a Multiplex Cockpit Sx transmitter?
Dear Alishanmao. I'm a huge fan and i love your videos. I have a futaba 7c 2,4ghz. I have a problem with setting up the fail safe because i am only able to set failsafe on ch 3 and not the ch 5:ger to activate the failsafe when the remote is off. Hope you can help me :-)
could u please make a video of what setting u need to adjust on ur radio and u receiver if i was just flying a basic quadcopter with kk.2 board???... i had a range problem with my radio and lost a quad....
Will the Naza And GPS have a upgrade to include more waypoints beside RTH?
Hi, Great videos. Something I am not quite grasping. Using a Futaba 7c For intelligent control mode, I have adjusted my channel 5 endpoint so it is in the Fail-safe (blue) area. Then when I disconnect and activate my mode switch I go between fail-safe to Att to failsafe. (rapid orange flashing). I have done a write each time. Also when I click on (3) Int. Or. Control, it instantly turns back off. Thanks!!
what motor r u using there bro?...it looked slick
Hello alishanmao, I have ordered a new DJI Naza system, do I need to change something on the computer when I want to fly in X mode? And also changing something on the transmitter? Or just setup on airplane mode and its done?:)
Thanks for nice video. I have futaba T6J. There is no 3 position switch. How should i configure control mode switch ? I would like to use all modes: manual , GPS and Altitude. Is the only possible way is to use pot control ? Thanks for any advice...
Nice video Ali, very helpful. I am using the Futaba T6XA and the only problem I have is that I cant bring channel 5 to Atti mode no matter what I do with ATV and SubTrims. Just wont go to Atti mode with the Channel 5 switch thrown in. Somehow using the Channel 6 knob to get into Atti mode. But that could be tricky. In every other way the T6XA seems to work OK. Any suggestions ? I need to bring ATV below 10 % and T6 doesnt do that. It goes from 10 to 120 %
awesome video! so i have a quesion, does the battery connect to the naza v2, and the naza connect to the esc? or does the battery connect to esc and naza? I am very confused about esc, naza, and reciever connections. please help. i am using opto esc.
Hello sir, nice video....i have a question that is this dji naza m lite supports i-bus connection with receiver...?
Thanks again for the very informational video. I'm using a Devo 10 radio and I'm using aux3(RUDD D/R) as a separate switch for failsafe. When setting failsafe on throttle do I put L 54% or H 54%? I'm not sure why there is a L or H.
We're would I be without u mr Ali thanks for your help!!!!
Lol, like me i'm a visual learner lol. Thanks on this video the End Points started making sense
How would you set up the Spektrum DX8 radio for fail safe ? It doesn't have , or I can't find a fail safe slection inside the radios programing screen
Ones you get to the field do you have to wait for the GPs to connect or ?
U need 2 make a video for spukrum tx
Thank you, well done. Love your help and ENTHUSIASM ! Could you do it with the DX8 too :( If it is as easy as you made it look, I'm placing my order this week. Done !
Have had the KK2.0. worked well. NOW having so many issues and problems i don't know where to start. I think i just decided I'm starting with a new FC. Nazza's looking good. :)
And if sacrifice manual for failsafe, I should always have throttle around 50% before switching the switch, and if I want to regain control, make sure my throttle is around 50%? Is there anyways to mix the switches so I can use a separate switch to activate failsafe without sacrificing manual? more specifically on Devo 8 radio.. thanks!!!
Is it possible to connect Vtx Transmitter to DJI Naza M V2 and is it possible to make it FPV ..?
Hi Ali I got a question. I broke one of the legs of my Ofm 450 and I can't find them on the Internet.where I can by them for separate?
Dusted off naza f450 m lite and bought a Futaba TJ8, this video was very helpful up and flying again
:]
Is it possible to calibrate the GPS with a 2-position switch as long as it is set up to switch between GPS and Manual mode?
OMG! I would be lost without you Alishanmao so I subscribed, clicked your ads, and clicked like. Im new to this Naza bizzo and it has been quite bewildering but your tutorials saved me. I have a Devo 8S with a Rx802, what should I select.. traditional, D-bus or PPM????? Googled it to death to no avail.
This is a really good setup guide!!
Can you make one with a Graupner MX-20??
or is there anyone out there who can send me a setting file?
Hi Ali,,,,I have follow your steps on this video and everything is ok,,,,,,when I reconnect back the drone it gives me a fast blinking red and i have the switch to the middle when I power up the tx and drone,,can u help..
Ali, the apple man and teacher man! :D Great video Ali! Thanks to you my english comes better now :D
You would like to send me the setup that you use in this video of the assistant naza ... a link of yours for me to download here
Putting together a new mount for the keychain #808 camera. Even with the props perfectly balanced, I get too much "Jello" effect with video playback. I need something to dampen the vibration.
Hi Ali,,,When I first time connect as per your video exacctly,,,there is a beeping sound coming from the motor or the esc just cannot distinguish which one,,,,can you help on this tq
Hi I am from India
Thanks for this Video
I have a f450 and I use dji Naza m light and flysky i6 transmitter
When I switch off my transmitter than my drone don't come back home position
Please help me please
I am Big fan of yours
Do you really need to set the fail safe throttle to 55% ???
I use Futaba 7cap, set the fail safe without taking care of setting the throttle, & it does a good job, when i switch the power off, it gets to 60ft high & comes back to its departure point....
Hey Ali, thanks for the tutorial video! I have set my failsafe so when I turn off radio, the slider goes to "failsafe", but the throttle at "holding", it returned home and landed without a problem. So I assume thats the same as you setting the throttle at 55% since when I'm up in the sky, the throttle is almost always around 50%. Or should I set it to 55% manually just in case somehow I'm not in that throttle range?
I want to built FPV quadcopter but I need only DJI Naza M V2 . Please help me I am in big confusion that can we setup Any other Vtx video camera transmitter to DJI Control board ?
i entered zeros configuring the gps and it was fine. i measured and entered the xyz and results were the same. wondering why have the xyz if it doesn't make any difference in gps performance.
Hi, Hope you can help. I have bought a RTF version of what you have here, DJI 450 and Futuba T8J. I have set it up in the same way as you have, but it will not power up the motors, everything else seems to work, I get a green light on the R2008SB receiver, but the DJI receiver blinks 1 red, two orange after I bind them? it goes through a series of blinks, including several green, but then just sits there and blink red/orange and nothing works? Any ideas.
Go home works without gps? I don't understand when speak, not native speaker - please, write even if you say the same in video. What would you recommend for area, where gps signal oftentimes losts? Thank you.
finally ,I believe my setup was done on the naza m lite but doesn't start motors and neither acquire satellites signal, how you solve that problem
I have my receiver bound but I am still unable to get the Assist software to pick up my receiver/tx Im using the 9xr and the FRsky D8R-II ... I choose PPM mode in Assistant but still not receiving any signal... motors will not arm or spin? Any ideas what I should do next? Thank you in advance!
can you send me setting for my futaba 8fg going on blade 400 and want to use naza h I no how to do naza just no luck setting radio for the blade 400
can you do a data link video with single waypoint please
need help. my naza is reveresd. how to fix it?
you forgot about setting up the compass? (moving 3 pos switch 6-10 times Calibration in horizontal and vertical axis) :)
Is there a reason that u r only doing bids on quads for the past several months??? Not criticizing, I'm just wondering.
is this m lite version 2 or version 1?
Hi Allshanmao
I tried to setup my futaba t8j by following your video but all the settings came out wrong,I am using the s-bus on the r2008sb receiver.I had to change the switch locations as follows
1 to get the gps,attitude and manual to work on switch e I had to use ch7
2 t0 get home lock etc to work on switch c I had to use ch6.
3 to get the vr knob to work I had to use ch5.
I tried to use the receiver as normal without using the s-bus but the naza lite unit would not link in.
I take it the f550 will still work with these settings.
Regards
Alan c
Ali help!? I have a Naza-M v2 I just buy from a friend. My PC is windows 8.1. I tried everything but can't even get my pc to recognize the naza when I plug the usb to the LED unit. Henceforth I can't even install the driver. When I plug in the LED just goes off does not turn solid green and my PC does not recognize it at all.. Any advice??
I bought Futaba T8J and F450 Quadcopter with Naza Lite. The DJI assist software I use is DJI NAZAM Assistant 2.20. I downloaded the drivers so my LED unit is recognized by the PC, but when I move the reemote sticks the display screen doesn't move at all!!! I don't know if I haven't downloaded enough things yet. ANYONE HAVE ANY CLUES, THANKS
Very good video
ALISHANMAO
I KNOW YOU USE FUTABA, AND BECAUSE OF THAT I BOUGHT IT.
THE SAME ONE LIKE YOU, FUTABA 14SG
Are u using naza v2? how is that possible? naza has only 8 channels. I have a retractable gear, lights, pan and tild for gopro and fpv , and i dont find the way to connect all of them together, I'm using futaba 14sg with sbus. its a f550.
1234channels are movements,
5 gps,altitutde, manual
6 curs lock , home lock
7 failsafe.
8 empty
so i only have channel 8.
Please help!
hi, I like to build a quadcopter with gps, but I don't know where how to start build one, so pls guide me to build one,I like to do with the quadcopter is fly it A point to B point using gps location, (and I am in india, Chennai) pls tell me where to get the parts all so. i
Hello i have a problem:i connect the battery,bind with my spectrum dx7s and then connect it to the computer with the cable that it came.I open the program but it doesn't detect it.i tried in another computer and the same results.What can i do ?
It knows where to land b/c of GPS it just does it slow for a controlled landing.
Hi There
I am setting up F 450 with E310 prop drive and E 420 esc. should i calibrate those esc as well.? please reply Becouse when i flow my f450 little bit of vibrating.
esc calib is must
Thanak you very much for your reply
Alishnmao
wht is the calibration steps for naza 3 please
I'm Just finishing up a DJI f450 build and I've run into a problem. I'm using a brand new Spektrum DX8 transmitter with AR8000 Receiver and TM1000 Telemetry Module. Everything is set-up and appears to be working properly on the assistant software... Bottom line is the motors only seem to throttle up properly when in Manual Mode... When I switch to Att or GPS Mode, throttle response is lazy and greatly reduced (can't take off!).... Any ideas??? I'm ready to take a sledge hammer to it!!! :-(
Nice video! I use a slightly different setup because of a different radio :). I have only one 3 way switch so i programmed a mixer for different switches into my radio it's quiet nice. Besides this i agree to your setup completely. People are so damn lazy! They can do it all by theirselves. JUST READ THE MANUAL OF THE TRANSMITTER AND THE NAZA! Instead they ask questions and steal your time.
Hi! What if you don't change the throttle to 54% in the failsafe settings?
Cheers
doesn't make difference, but just for safety reasons. its ancient tech
Great job!
Hi ALi,, I am planning to buy used Naza m Lite from somebody,, Can it still be used ? after they might use it in different motor, esc and Tx-Rx,,
what is this Intelligent Orientation use for ? kind of confused
how do you turn off mc output , my is on with red .
thanks
Spektrum please.
when I move my switch A on my Turnigy TGY i10 fo between the left side blue box to failsafe and then to the right blue box in the slider , why dont show me Manual and GPS selected in blue
Hi. im using a Turnigy 9x and getting a CFG-ERR on dji naza assistant program.
this is the error: CFG-ERR
Configuration error, this may cause by firmware upgrade from old version. or abnormal Tx calibration. Re-calibrate your transmitter, and power cycle your controller and check all of the parameters.
Is there someone who know what i should do?
Very helpful for F450 setting
Any idea what would cause this change? With my FW-450 with Naza-M, after setting everything up after mounting the GPS on it, throttle worked normally gradually increasing motor speed as throttle moved from low to full. But last time I flew it, after starting motors, leave throttle closed and as usual, motors would shut off after about 3 seconds, but if throttle opened, motors remained just slowly turning until throttle got to just under 1/2, then motors started speeding up but instead of lift-off just over 1/2, had to open throttle to around 3/4. Once Naza system realized quad was flying, throttle acted normally and I had to close throttle back to just over 1/2 to prevent rapid climb, but once landed at under 1/2 throttle, close throttle just 1 or 2 clicks lower and motors would suddenly slow to speed they normally turn just after starting motors and maintain that motor speed all the way from just below 1/2 to full closed stick position.
Now, arming still works as usual, but I get absolutely NO motor response from throttle closed to throttle just under 1/2, then sudden motor speed change near 1/2 and smooth throttle response from just over 1/2 to full throttle.
can any one help please...my naza m lite is not talking with my laptop pls help
Hi Ali I follow exactly as per your video,,but when I throttle up the bird just wont lift off,,,even with 100% throttle .......can u help Tq Assalamualaikum
won't lift off means something wrong with your setup. either props spinning in wrong direction or your setup is too heavy to take off
Replace your ESC speed controller's use a 30 amp this way you can handle the 4 cells.
I cant get the software install on my mac computer. Can anyone help?
Part 2?
some one knows .. if you connect naza to computer ,and you get weak green light ,what is the Problem?.i need to upgrade and i cant ,,, thx
Do you also power up your Naza-M with a LIPO battery?
ABMNS PRODUCTION
thx this is already fixed... was the firmware from the port of the computer ...
FLYCOMPANY DruMCoMPanY Good :)
ABMNS PRODUCTION
:)
mr ali i learned to allow you to assemble Multicopter through email I Wiko of Indonesia
Hi... My DJI Phantom work with out any problem it does communicate with the software with in no time. But, My DJI Naza m lite brand new out of the box. LED kept bring fast red. you said, it not program yet. I try to connect it to my Naza m V2 software. but it not communicate with the software. On the software bottom left show " MC Out Put" on red to white while plug the USB cable in. and the software said please connect to the controller. Can anyone help me how to fix this problem.
I am having the same problem
E310 and e420 esc calibration
I plugged in my Remote LED into my PC but every time it says USB Malfuntioned, anyone able to help?
Forgot to mention I'm trying to use this to setup my new Naza M V2.
at about 8min you start saying what you are going to do but doesn t make sense if you don t say why you are doing it
His pentium d with w7 is faster than my next gen i5 with w10
My name is Naza XD
I purchased the naza lite with gps got it for fathers Day and still cannot fly it.
I am ready to take it back for refund and purchase the ideafly at least I kn I w it will work.
Thumps down from me on naza. Call the tect support he helped me with the driver but he has so many people waiting for help like me that he tells you he has to go and email him if you cannot get it to work.
We'll guess what he will not respond.
Hobby shop where I purchased cannot help $225.00 down the drain.
Only doing vids, sorry.
just want to say thank
Vthe