I went with the LHY board and LHY linear power supply in my N130. I stream to an outboard DAC. Boy what a difference! I thought this was all snake oil, but figured for $279, why not. Worth every penny! Opened everything up, using the Ares II DAC, it was like a veil or wet blanket was lifted, the difference was quite obvious, and for the better.
Thx Hans, a relevant upgrade 4 all Node users that fits from a financial standpoint...overlooked by the majority of reviewers! (Like the guy who swore by a $550 1m digital cable tested on $399-1299 DAC's; just irrelevant I think)
I did an upgrade of this board with the Allo Shanti LPSU on my Node 2i, and it brought about quite a change. More bass definition, slight bump in upper mid bass, and definitely more definition and refinement in the top end. This was the internal DAC. This was as big an upgrade for me as adding my external DAC, which is a SMSL VMV D1SE
Great review. I installed the interface on both a N130 and 2i. In both cases I use the units for streaming into external DACs. The improvement was significant and very noticeable (better separation, blacker backgrounds, improved dynamics) but will obviously vary depending in the transparency of your system. One of the best value for money improvements in my system.
Thanks for the video. Just upgraded my Node 130, (PD interface and Allo Shanti), connected to Roksan Caspian M2 and Focal Chora 826. Finally i can hear details i was used to hear in my headphone setup (chord hugo 2, focal clear etc.) Strongly recommended to all Node owners ;)
Excellent review Hans. Based on your review I purchased the PD Creative interface board and power supply to upgrade my Node2i. It was delivered quickly, simple to install and after living with it for a few weeks I'm very happy with the improvement. I run my Node2i through a Chord DAC and the improvements to the sound of my system were not insignificant and consistent with your comments. In the past, I used the Node2i to play incidental music from Tidal or my own networked music library (CD quality or higher) while I was doing other stuff around the house. Serious listening to music was through my CD player or turntable. However, I now find myself listening to the Node2i as a primary music source more and more. Thanks again and once more your channel has helped me make a rationale change to my system, for the better!
Thank you very much for this worth review again, Hans! Thinking on upgrading my "lucky" Node2 since a while. This could be a good direction for me. Thank you for your work! Karoly
I upgraded my N130 with their ultra low noise PSU and board. The Node’s USB goes out into my Holo Spring 3 KTE DAC. There is discernible improvement in the bass and high range. Mids are more or less the same.
I have the node n130 and the PD Creative PWR Module with Allo Shanti going to a Denafrips Ares2. And let me say that the Ifi SPDIF Purifier 2 made a HOLY COW Upgrade pretty much across the spectrum (audiophile superlatives here). I found SPDIF to sound better than the newly firmware updated USB on the node. Powered by the seconded Shanti 5v tap and after the 150hr break-in period, this is probably the best 200 I`ve spent on hi-fi in 30 years. Great channel BTW.
Interesting. I was wondering if it also provides an upgrade in sound if you bypass the bluesounds internal dac, rather than use it as Hans showed. So I take it from this comment, the answer is 'yes' then :)
S@@Pete.across.the.street i have the 2i, and i was thinking about upgrading to the Node 130 so that i could use USB.. perhaps i will keep the 2i and just get the IFI SPDIF purify 2?
Dankjewel Hans, Did you also try the digital out of the node? Would it help for that as well, or does it mainly help when using the internal dac (asking since I use an external dac and go coax out from the node2i)
Ive upgraded my N130 with PD-Creative PSU, not really noticed any improvement for internal DAC. Meanwhile sound of external DAC improved dramatically: better sound stage, more low end, way better clarity - another league sound.
Yes, the sound improvement is very evident with an external DAC. Best hifi money I have spent for any upgrade like this, short of entire new audio pieces. Worth every penny.
I am using my Node 2i as a streamer only, and my DAC of choice - the amazing Geshelli Labs J2 AK4493 is using a third party linear power supply; which as you note makes an enormous improvement in the sound quality. Did you also try the Node 2i as a streamer only with the PD Creative power supply? If so, is it "worthwhile" in your opinion?
Bluesound N 130. Topping D90 SE DAC. After 5 hr listening i can assume, that my sound has changed. First i noticed, the bass is less prominent, seems cleaner. . I had to give the sub a few clicks up to bring it to my pleasure. Second, the highs are a tick softer, lesser edgy. The soundstage is wider. Thats for the short time of listening for now.
Hi Hans I’ve been considering this upgrade for my node. Do you think it will improve the sound quality if I’m using the digital outputs as a transport? Some people say no but your opinion is the one I’m after. As always I respect you views more then anyone else. Thank you 🙏
Very nice video, thank you very much! Did you test, if the sound quality also improves when using the Bluesound only as the "Transport" and with an external DAC? (I run my Bluesound Node with Digital RCA out to an Accuphase DP-510). Thanks and Regards!
Hi Hans, thank you for your informative video(s)! I have a question, what in your opinion would be the best streamer to connect to my 20 y.o. Linn system? The choices I am pondering are: (1) Node X; (2) N130 w/PSU; (3) Linn Sneaky DS 2008 model; or (4) Linn Sekrit DS 2011 model? My heart tells me to go with Linn, but I wonder if those units, due to their age, would not be as good as the BluOS options maybe? Your thoughts and advice are greatly appreciated...
Sure, but do you think the Linn streamers I mentioned, being over 20 years old, would not be able to compete with the latest DAC's used in the Nodes?@@TheHansBeekhuyzenChannel
Dear Hans, thank you for your interesting video’s. Because of this video post I’m very curious. Are you able to answer my question. 😊 I’m a happy user of a Bluesound Node (130) connected to an external dac. It’s the Denafrips Ares II. Cable is the optical AQ Cinnamon. Now my question. Do you think it makes a sonical improvement if I would install the linear power supply? Only answers I could find on the internet are with Coax or USB connection. Thank you very much in advance for taking the time and keep up the good work 😊. Greating, Olaf from The Netherlands
@@TheHansBeekhuyzenChannel Thank you for taking the time in answering. Regarding the rest of the equipment. I’m using a “vintage” Linn Intek amp and Linn Nexus loudspeakers. Plus the external dac Denafrips Ares II in combination with the Bluesound Node (130) via Optical. What do you think?
Thank you very much for all the great videos. I have yet to experiment with using external power supplies. To address jitter and clocking, I decided to incorporate the Denafrips Hermes DDC between my Denafrips Pontus II DAC and digital sources, such as the Bluesound Node. All my components are fronted by Panamax M5300-PM power conditioners. All of my power, speaker and interconnect cables are upgraded. Would my Node still benefit from an external power supply?
Yes, I bought the LHY kit Alvin at Vinshine Audio is selling for my N130, it made a profound difference in my Node's streaming sq. I use the Ares II DAC, Venus II is on the way. I thought all of this was snake oil, boy was I wrong. Worth every penny.
Hans, I'm seriously considering this upgrade for my Node 2i. But I'm thinking of purchasing an Allo Shanti as the LPS as it has two DC outputs; the 2nd being for an external DAC. My concern is that the DC cables are hardwired and of uncertain audio sonic quality. Would it be better to get the PC Creative LPS so as to use separate higher end DC cables? Or would it be worth replacing the Shanti cables by installing chassis mounted sockets and, again, using separate DC cables. I'd appreciate your thoughts. And thank you for such useful and easily understandable videos. I'm not an engineer, just a very amateur audio enthusiast and look to "experts" such as yourself to assist us in making smart and useful choices.
I'm going to order the PD creative kit. considering a correct cost-benefit ratio, does it make sense to buy the cheaper version with an external medical power supply instead of the version with the "super low noise power supply"?
great, but my question would, considering your review on the s-booster an the farad power supply would it be better getting just the interface an one of those supply's?
@@TheHansBeekhuyzenChannel well you can buy only the interface for the bleusound . I ask my self, would the the s-booster or even pair with the farad MK 3 (more expensive, not sure I want to do that yet) be better than the linier power supply P-D is offering in there kit. This is more a question: value for the money actually I use the Node2I only as a transport connected to a Moon280D (which I'm in the process of upgrading. Holo S3 an May Kte or L2 are on my test list for now )
Would this upgrade be worth it if the node 2i is only used as a transport? My Node 2i goes into an external DAC of very high quality. Would like a better streaming transport and I wondering if this power supply upgrade will do that.
Hi Hans in terms of cost benefit what do you think would improve the sound quality of the bluesound node 2i more the use of this power supply or a first generation dac mojo where would you start to improve the system I use a rega Brio amplifier latest model with Dynaudio Emit M20 speakers greetings thanks for your excellent channel.🤗👍
The cost for Spain is €315, the truth is that it is worth it. A wonder how the Yello group sounds is worth the investment because now for sound and the interface of the Bluesound Node 2i they are unbeatable. Thanks Hans 👌👍
@@TheHansBeekhuyzenChannel ok, I asked because I often read about "Netzfilter" etc.... Do You have Information about those things? The Information here on other UA-cam mostliy sounding like vodoo or snakeoil. I never found a such scientiffic and plausible source than yours.
Hello. Thanks for your video. I have in NODE 2021 connected to an FDA Quloos A690 in Spdif or USB. Can the power supply shown in the video have an impact on my assembly? Or an ifi spdif ipurifier as said below in the comments is sufficient? thank you
The original power supply is quite bad indeed, I had bad power and disturbances from thé wall in my last apartment and everytime a light, thé oven, or anything turned on, thé sound was cut for à short time.
There only is a 230 volts version of the exterior power supply. You can use the board that replaces the internal power supply and another 5V 2A external power supply.
Hi Hans, Maurizio from Verona Italy. I've a suggestion for you. A Video Review of a DYI Board. Arylic Up2Stream HD DAC, complete with Case & Remote. Low Costs but Great Performances Curious of Your enlightened judgment 💡 Thanks & Regards Maurizio
@@TheHansBeekhuyzenChannelWell..Is classified like DIY olny for price issue. But really Is the same of Ready to use Arylic S50 Pro+. You can use with or without case and with or without remote as you want to spent. But imho Is much better 'cause the different DAC ESS9038Q2M and moreover non downsampling at Red book CD resolution by Linkplay Wi-Fi Board ..1:1 at 24/192. (Like Node 2I). Anyway, thanks for your attention. Maurizio
I went with the LHY board and LHY linear power supply in my N130. I stream to an outboard DAC. Boy what a difference! I thought this was all snake oil, but figured for $279, why not. Worth every penny! Opened everything up, using the Ares II DAC, it was like a veil or wet blanket was lifted, the difference was quite obvious, and for the better.
👍🏼
Thx Hans, a relevant upgrade 4 all Node users that fits from a financial standpoint...overlooked by the majority of reviewers! (Like the guy who swore by a $550 1m digital cable tested on $399-1299 DAC's; just irrelevant I think)
I did an upgrade of this board with the Allo Shanti LPSU on my Node 2i, and it brought about quite a change. More bass definition, slight bump in upper mid bass, and definitely more definition and refinement in the top end. This was the internal DAC. This was as big an upgrade for me as adding my external DAC, which is a SMSL VMV D1SE
Great review. I installed the interface on both a N130 and 2i. In both cases I use the units for streaming into external DACs. The improvement was significant and very noticeable (better separation, blacker backgrounds, improved dynamics) but will obviously vary depending in the transparency of your system. One of the best value for money improvements in my system.
Thanks for sharing
Is the improvement evident even if you use an external dac to the node?
@@andreacountry8471 Yes this is a very good question.
The dac is in no way serious to use if you want to improve on the level discussed.
@@onnonugteren2935 yesterday I resolved the issue, yes there is improvement even with external dac...I try in my Node😉
@@andreacountry8471 Yes, very, I am using the LHY setup Alvin at Vinshine Audio sells.
Have this and it’s great, alongside the sBooster LPS. Thanks for the video!!
Enjoy it
Thanks for the video.
Just upgraded my Node 130, (PD interface and Allo Shanti), connected to Roksan Caspian M2 and Focal Chora 826.
Finally i can hear details i was used to hear in my headphone setup (chord hugo 2, focal clear etc.)
Strongly recommended to all Node owners ;)
Sounds great!
Excellent review Hans. Based on your review I purchased the PD Creative interface board and power supply to upgrade my Node2i. It was delivered quickly, simple to install and after living with it for a few weeks I'm very happy with the improvement. I run my Node2i through a Chord DAC and the improvements to the sound of my system were not insignificant and consistent with your comments. In the past, I used the Node2i to play incidental music from Tidal or my own networked music library (CD quality or higher) while I was doing other stuff around the house. Serious listening to music was through my CD player or turntable. However, I now find myself listening to the Node2i as a primary music source more and more. Thanks again and once more your channel has helped me make a rationale change to my system, for the better!
Enjoy the music
Have connected my Node 2i to a SMSL D300 DAC. Sound quality improvement is enormous. It seems a more obvious upgrade path that requires no tinkering.
And then add the power supply.....
Hans, you're a valuable treasure. I appreciate your videos very much!
I appreciate that!
Thanks! Am considering a PD Creative LPS for my Node 2i, so appreciate your thorough look at it!
Thank you too
Thank you very much for this worth review again, Hans! Thinking on upgrading my "lucky" Node2 since a while. This could be a good direction for me. Thank you for your work! Karoly
👍🏻
Where is I can buy?
I upgraded my N130 with their ultra low noise PSU and board. The Node’s USB goes out into my Holo Spring 3 KTE DAC. There is discernible improvement in the bass and high range. Mids are more or less the same.
Use coax men. Usb is so so. Coax much better sounding. Cheers.
I have the node n130 and the PD Creative PWR Module with Allo Shanti going to a Denafrips Ares2. And let me say that the Ifi SPDIF Purifier 2 made a HOLY COW Upgrade pretty much across the spectrum (audiophile superlatives here). I found SPDIF to sound better than the newly firmware updated USB on the node. Powered by the seconded Shanti 5v tap and after the 150hr break-in period, this is probably the best 200 I`ve spent on hi-fi in 30 years. Great channel BTW.
Interesting. I was wondering if it also provides an upgrade in sound if you bypass the bluesounds internal dac, rather than use it as Hans showed.
So I take it from this comment, the answer is 'yes' then :)
(Or was it the purifier that caused the holiness of the cow?)
@@Kah0ona It was the Ifi SPDIF purifier 2 that made the holy Cow moment, much more so than the Node PWS upgrade.
Ifi spdif ipurifier 2 is awesome! I had the same improvements
S@@Pete.across.the.street i have the 2i, and i was thinking about upgrading to the Node 130 so that i could use USB.. perhaps i will keep the 2i and just get the IFI SPDIF purify 2?
Dankjewel Hans,
Did you also try the digital out of the node? Would it help for that as well, or does it mainly help when using the internal dac (asking since I use an external dac and go coax out from the node2i)
good point, me too.
i suggest that anyone upgrade the AC cable first that comes with the Node 2i, it makes a big difference. i am using a Kimber Power Cord.
Ive upgraded my N130 with PD-Creative PSU, not really noticed any improvement for internal DAC.
Meanwhile sound of external DAC improved dramatically: better sound stage, more low end, way better clarity - another league sound.
I currently use the Bluesound Node 2i so i will consider this upgrade. Thank you!
Enjoy!
Just FYI, Fidelity Audio (UK) also has similar upgrade kits for the Bluesound Node.
Although they appear to be more expensive
Was wondering if the upgrade makes sense when not using Node's internal dac
It makes A LOT OF Sense, the better the DAC is the more you will benefit from clean power of streamer.
I use the Node 2i with an external Pontus DAC and I did the modification to use a SBooster LPS and it made a difference
Sure, it actually doesnt really affects internal dac sound IMO, but really improving sound of the external one.
Yes, the sound improvement is very evident with an external DAC. Best hifi money I have spent for any upgrade like this, short of entire new audio pieces. Worth every penny.
I am using my Node 2i as a streamer only, and my DAC of choice - the amazing Geshelli Labs J2 AK4493 is using a third party linear power supply; which as you note makes an enormous improvement in the sound quality. Did you also try the Node 2i as a streamer only with the PD Creative power supply? If so, is it "worthwhile" in your opinion?
Yeah, ive upgraded N130 with that kit, internal dac sound barley affected, but external dac performance jumped to another league.
@@leo_kazantsev on my 2i the change of this kit made a massive difference (with internal DAC).
Does it improve the digital output too?
Two "Thumb-pups" Hans!
🐶👍🐶👍
Yes it does.
Bluesound N 130. Topping D90 SE DAC. After 5 hr listening i can assume, that my sound has changed. First i noticed, the bass is less prominent, seems cleaner. . I had to give the sub a few clicks up to bring it to my pleasure. Second, the highs are a tick softer, lesser edgy. The soundstage is wider. Thats for the short time of listening for now.
Great to hear!
Hi Hans
I’ve been considering this upgrade for my node.
Do you think it will improve the sound quality if I’m using the digital outputs as a transport? Some people say no but your opinion is the one I’m after.
As always I respect you views more then anyone else.
Thank you 🙏
Yes, there will be a sound improvement.
Very nice video, thank you very much! Did you test, if the sound quality also improves when using the Bluesound only as the "Transport" and with an external DAC? (I run my Bluesound Node with Digital RCA out to an Accuphase DP-510). Thanks and Regards!
It will also improve the digital output.
@@TheHansBeekhuyzenChannel thank you for your reply
Hi Hans, thank you for your informative video(s)! I have a question, what in your opinion would be the best streamer to connect to my 20 y.o. Linn system? The choices I am pondering are: (1) Node X; (2) N130 w/PSU; (3) Linn Sneaky DS 2008 model; or (4) Linn Sekrit DS 2011 model? My heart tells me to go with Linn, but I wonder if those units, due to their age, would not be as good as the BluOS options maybe? Your thoughts and advice are greatly appreciated...
I can't get Linn equipment for review, for the rest, see my review. That is why I make them
Sure, but do you think the Linn streamers I mentioned, being over 20 years old, would not be able to compete with the latest DAC's used in the Nodes?@@TheHansBeekhuyzenChannel
Dear Hans, thank you for your interesting video’s. Because of this video post I’m very curious. Are you able to answer my question. 😊
I’m a happy user of a Bluesound Node (130) connected to an external dac. It’s the Denafrips Ares II. Cable is the optical AQ Cinnamon. Now my question. Do you think it makes a sonical improvement if I would install the linear power supply? Only answers I could find on the internet are with Coax or USB connection. Thank you very much in advance for taking the time and keep up the good work 😊.
Greating,
Olaf from The Netherlands
There will be sonic improvement, whether that improvement is audible to you depends on your equipment and your ears.
@@TheHansBeekhuyzenChannel Thank you for taking the time in answering. Regarding the rest of the equipment. I’m using a “vintage” Linn Intek amp and Linn Nexus loudspeakers. Plus the external dac Denafrips Ares II in combination with the Bluesound Node (130) via Optical. What do you think?
Thank you very much for all the great videos. I have yet to experiment with using external power supplies. To address jitter and clocking, I decided to incorporate the Denafrips Hermes DDC between my Denafrips Pontus II DAC and digital sources, such as the Bluesound Node. All my components are fronted by Panamax M5300-PM power conditioners. All of my power, speaker and interconnect cables are upgraded. Would my Node still benefit from an external power supply?
I think so.
Yes, I bought the LHY kit Alvin at Vinshine Audio is selling for my N130, it made a profound difference in my Node's streaming sq. I use the Ares II DAC, Venus II is on the way. I thought all of this was snake oil, boy was I wrong. Worth every penny.
Hans, I'm seriously considering this upgrade for my Node 2i. But I'm thinking of purchasing an Allo Shanti as the LPS as it has two DC outputs; the 2nd being for an external DAC. My concern is that the DC cables are hardwired and of uncertain audio sonic quality. Would it be better to get the PC Creative LPS so as to use separate higher end DC cables? Or would it be worth replacing the Shanti cables by installing chassis mounted sockets and, again, using separate DC cables. I'd appreciate your thoughts. And thank you for such useful and easily understandable videos. I'm not an engineer, just a very amateur audio enthusiast and look to "experts" such as yourself to assist us in making smart and useful choices.
I haven't tried so I can't say.
I'm going to order the PD creative kit. considering a correct cost-benefit ratio, does it make sense to buy the cheaper version with an external medical power supply instead of the version with the "super low noise power supply"?
I would not..
The 1060 PLN kit is sold out. Any recommendations for power supplies to go with the 350 PLN kit??
great, but my question would, considering your review on the s-booster an the farad power supply would it be better getting just the interface an one of those supply's?
You lost me
@@TheHansBeekhuyzenChannel well you can buy only the interface for the bleusound .
I ask my self, would the the s-booster or even pair with the farad MK 3 (more expensive, not sure I want to do that yet) be better than the linier power supply P-D is offering in there kit. This is more a question: value for the money actually
I use the Node2I only as a transport connected to a Moon280D (which I'm in the process of upgrading. Holo S3 an May Kte or L2 are on my test list for now )
Does anyone have a stock power supply for sale? Mine just crapped out.
I just have a "Bluesound Node". Is this different from the 2 or 2i? I am interested in this power supply upgrade.
my 2.i sounds great without the mod. however i might add that i have $6K worth of DAC/Amp/ and speakers in the chain.
The PSU makes it even better 😊
Would this upgrade be worth it if the node 2i is only used as a transport? My Node 2i goes into an external DAC of very high quality. Would like a better streaming transport and I wondering if this power supply upgrade will do that.
It would surely help.
@@TheHansBeekhuyzenChannel Thank you for the reply
Hi Hans in terms of cost benefit what do you think would improve the sound quality of the bluesound node 2i more the use of this power supply or a first generation dac mojo where would you start to improve the system I use a rega Brio amplifier latest model with Dynaudio Emit M20 speakers greetings thanks for your excellent channel.🤗👍
I would start with the power supply
Thanks Hans I do enjoy the music too 🎶🎼🎵☝️🎉
The cost for Spain is €315, the truth is that it is worth it. A wonder how the Yello group sounds is worth the investment because now for sound and the interface of the Bluesound Node 2i they are unbeatable. Thanks Hans 👌👍
Thank you! I have already a NAD C658/ C298 combo. But how can I improve the power supply for that?
You can't. (well, everything is possible, but it would require extensive understanding of audio electronics).
@@TheHansBeekhuyzenChannel ok, I asked because I often read about "Netzfilter" etc.... Do You have Information about those things? The Information here on other UA-cam mostliy sounding like vodoo or snakeoil. I never found a such scientiffic and plausible source than yours.
Is the upgrade worth it if I am doing optical digital out of the 2i?
That depends also on the DAC but in general: yes
Now if only the folks st Nad had given the C685 a digital output.. 🤦♂️
Would this PSU upgrade work with the Powernode 2i ?
I don’t think so
Is it a problem to put the unit on an pre-amp?
Sorry, no
Hello. Thanks for your video. I have in NODE 2021 connected to an FDA Quloos A690 in Spdif or USB.
Can the power supply shown in the video have an impact on my assembly? Or an ifi spdif ipurifier as said below in the comments is sufficient? thank you
Start with the power supply
@@TheHansBeekhuyzenChannel Thank you for your reply. So the kit at 1060.00 pln?
@@stjah69 If your grid is at 230 volts. Else buy the cheapest kit and get a quality audiophile power supply that delivers 2 amps at 5 volts.
@@TheHansBeekhuyzenChannel Yes I am in France. So 230V. Ok then I have to take the kit at 1060.00 PLN
@@stjah69 👍🏻
The original power supply is quite bad indeed, I had bad power and disturbances from thé wall in my last apartment and everytime a light, thé oven, or anything turned on, thé sound was cut for à short time.
'Quite bad' doesn't do it justice. It's an average PSU that can be improved by an external one.
@@TheHansBeekhuyzenChannel mine may have à flaw At that stage then.
Compatible with US 115V ?
Yes
Not the power supply though
There only is a 230 volts version of the exterior power supply. You can use the board that replaces the internal power supply and another 5V 2A external power supply.
So which power supply would you recommend?
Checkout the Allo Audio Shanti LPS it has 2 taps one 5v/3a for the Node and a 5v/1 amp for something else.
I find he PD Creative very good and affordable.
@@TheHansBeekhuyzenChannel For the average person, would you suggest the standard power supply or the “Super Low Noise” power supply?
Thank you.
The latter!!
@@mikemajors2385 Hi Mike,
The Allo Shanti LPS is about the same price as the Super Quiet PSU from PD. What makes it better?
Thanks.
Hi Hans --sent you an email on a componant
Sorry but I can't answer those kinds of emails. I actually don't see them for they are kept away from me. Questions can be asked here.
Hi Hans,
Maurizio from Verona Italy.
I've a suggestion for you.
A Video Review of a DYI Board.
Arylic Up2Stream HD DAC, complete with Case & Remote.
Low Costs but Great Performances
Curious of Your enlightened judgment 💡
Thanks & Regards
Maurizio
It's too much DIY, I review only ready to use consumer products.
@@TheHansBeekhuyzenChannelWell..Is classified like DIY olny for price issue.
But really Is the same of Ready to use Arylic S50 Pro+.
You can use with or without case and with or without remote as you want to spent.
But imho Is much better 'cause the different DAC ESS9038Q2M and moreover non downsampling at Red book CD resolution by Linkplay Wi-Fi Board ..1:1 at 24/192. (Like Node 2I).
Anyway, thanks for your attention.
Maurizio