# DIFF ALL (to paste into BF 4.2.3 for the US65PRO. This assumes you have BLHeli_M ESC firmware and FrSky RX # feature feature -AIRMODE feature -ANTI_GRAVITY feature MOTOR_STOP # beacon beacon RX_LOST beacon RX_SET # map map AETR1234 # serial serial 0 64 115200 57600 0 115200 serial 1 2048 115200 57600 0 115200 # aux aux 0 0 0 1700 2100 0 0 aux 1 1 1 1300 1700 0 0 aux 2 13 1 1700 2100 0 0 aux 3 28 1 900 1300 0 0 aux 4 35 2 1700 2100 0 0 # adjrange adjrange 0 0 1 900 1200 12 1 0 0 adjrange 1 0 1 1200 1800 12 1 0 0 adjrange 2 0 1 1800 2100 12 1 0 0 # vtxtable vtxtable bands 6 vtxtable channels 8 vtxtable band 1 BOSCAM_A A CUSTOM 5865 5845 5825 5805 5785 5765 5745 5725 vtxtable band 2 BOSCAM_B B CUSTOM 5733 5752 5771 5790 5809 5828 5847 5866 vtxtable band 3 BOSCAM_E E CUSTOM 5705 5685 5665 0 5885 5905 0 0 vtxtable band 4 FATSHARK F CUSTOM 5740 5760 5780 5800 5820 5840 5860 5880 vtxtable band 5 RACEBAND R CUSTOM 5658 5695 5732 5769 5806 5843 5880 5917 vtxtable band 6 IMD6 I CUSTOM 5732 5765 5828 5840 5866 5740 0 0 vtxtable powerlevels 2 vtxtable powervalues 0 1 vtxtable powerlabels 25 200 # master set gyro_lowpass2_hz = 375 set dyn_notch_width_percent = 0 set dyn_notch_q = 250 set dyn_notch_min_hz = 125 set dyn_notch_max_hz = 350 set dyn_lpf_gyro_min_hz = 300 set dyn_lpf_gyro_max_hz = 750 set acc_calibration = 27,-59,-67,1 set mag_hardware = NONE set baro_hardware = NONE set rssi_channel = 8 set serialrx_provider = SBUS set dshot_bidir = ON set motor_pwm_protocol = DSHOT300 set motor_poles = 12 set vbat_warning_cell_voltage = 300 set ibata_scale = 1175 set yaw_motors_reversed = ON set small_angle = 180 set deadband = 2 set yaw_deadband = 2 set osd_warn_batt_not_full = OFF set osd_warn_batt_warning = OFF set osd_warn_esc_fail = OFF set osd_warn_core_temp = OFF set osd_vbat_pos = 2433 set osd_rssi_pos = 2362 set osd_tim_2_pos = 2423 set osd_flymode_pos = 2457 set osd_throttle_pos = 2392 set osd_current_pos = 2368 set osd_mah_drawn_pos = 2400 set osd_craft_name_pos = 2442 set osd_warnings_pos = 2345 set osd_avg_cell_voltage_pos = 353 set osd_disarmed_pos = 2314 set osd_stat_tim_1 = ON set osd_stat_max_spd = OFF set osd_stat_battery = ON set osd_stat_bbox = OFF set osd_stat_bb_no = OFF set debug_mode = SMARTAUDIO set vtx_band = 5 set vtx_channel = 1 set vtx_power = 1 set vtx_freq = 5658 set gyro_1_align_yaw = 900 set name = US65PRO profile 0 # profile 0 set dyn_lpf_dterm_min_hz = 105 set dyn_lpf_dterm_max_hz = 255 set dterm_lowpass2_hz = 225 set p_pitch = 69 set d_pitch = 68 set p_roll = 63 set d_roll = 62 set p_yaw = 68 set d_min_roll = 0 set d_min_pitch = 0 profile 1 profile 2 # restore original profile selection profile 0 rateprofile 0 # rateprofile 0 set rates_type = ACTUAL set roll_rc_rate = 1 set pitch_rc_rate = 1 set yaw_rc_rate = 1 set roll_expo = 54 set pitch_expo = 54 set yaw_expo = 54 set roll_srate = 100 set pitch_srate = 100 rateprofile 1 rateprofile 2 rateprofile 3 rateprofile 4 rateprofile 5 # restore original rateprofile selection rateprofile 1 # save configuration save
Thank you, it turned out great. I tried it on the de65pro with 19k motors on 1s, the native ones are faulty. Plus 1 minute flight time 4.30-4.50 vs 3-3. 20
Very helpful. I love this quad and am playing with its setup. Thanks for the Diff all! I am going to try this this weekend and record some DVR. Also may upsize it to a 75mm frame. Also I know this was a little bit ago that you did this, but the GNB27 connector batteries work well and can be found may places including Amazon (GNB 300 and the GNB 450). I cut the battery try out and use a very light velcro strip for battery retention and that has helped a ton, as I was having the same sticker issue you were.
UAV Tech Sure ;-) you help a lot more 😄 I couldnt find those on BG but ordered a set on Aliexpress. Always good to have stuff like this in stock My De65 is still in transit. Cant wait to theow youre tune on there
This is a great review. Straight to the point and exactly what I needed to know. I have this whoop on the way and I look forward to applying all of your upgrades and PIDS. Thank you very much and I will let you know how it goes.
lordy lordy thank goodness for this walk through on this quad! I bet it'll sell like hot cakes and a trillion people will be looking for better tunes. great to have this available! GNB has had this connector out for quite a few months now - you can buy their batteries, but not from retailers yet AFAIK. Worth cautioning though that you can really make life inconvenient if you botch a BLHeli flash. New users should be really careful that the board has stable power while flashing - it's not like an aborted flash with an FC that you can just start over easily via USB. A power interruption during a blheli flash can mean you're committing yourself to some fine soldering so you're able to flash via the C2 method.
@@uavtech oh yeah! ... i actually think they're great, too. especially if you're using two of them like this 2S fairly low draw config and you're using the solid pin ones? super light - already a zillion chargers and batteries with that standard. not a lot reasons to switch for me!
I've gotten GNB 1s with GNB27 from Amazon in the states. I didn't use them though, since I've switched everything to XT30. I moved from PH2.0 because eventually the connectors are so loose they can't keep the quad in the air, with lots of little disconnects and reconnects.
Thanks Man! Yep totally love this little thing but I had no Idea about the yaw washout. I thought it was a coanda effect or something of how these craft fly when I went for a steep descending dive. Keep in mind this IS my first whoop and didn't know any better about performance nuances for these. P.S. Did you mod the RX and VTX? 🤔
@@uavtech Ah....I got little wire stubbies for the RX and VTX. It was hard to tell in your video bit it looked like you modded FrSky antennas for those modules. Perhaps they are upgrades from what I have.
Hello ☀️ I just got my DE65 Pro today :-) So I tried to flash blheli at the point 'Select version' it only shows the newest verion '16.7.1 [Official, beta]. How do I get '16.9'? Edit: solved. I had the wrong configurator version 😏
This battery connector war is Ridiculous !! I don’t understand WHY WE DIDNT JUST USE THE DEANS MICRO T connector FROM THE GET GO . It’s been around for what a decade? We don’t need every company making there own connector. It’s Absurd. It’s making me hate all of my tinywhoops.
Good video! Have an issue with my 65 Pro I updated the firmware on mine and probably should not have. Does anybody have a backup of the .hex file for it?
Here in the UK I found a seller selling GNB et2.0/gnb27 for really good prices! Also I think it’s harder to put the batteries in with the r xsr version.
@@Z4nd3r-D sure, here’s a link: www.ebay.co.uk/itm/233714163786 If you scroll down and see the seller’s other items you’ll see a bunch of other sized gnb27 lipos
I test and compare many firmwares from jazz maverick and i think best is 16.77 48khz ... it is more stable than others. If you want rpm use dshot 300 .
@@t.me_hgjhghgf yea, i've set up rpm filters on 16.73 for whoops through 5" but was reading the forum where above 16.73 had issues. i just made all the changes here and it read 0 errors on motors, so i'm going to test it tentatively :)
@@Sully365 on my quads ( 3 to 5 inch) more stable maverick firmware 16.78 , others incl 16.9 have some glitches in flight , rpm reads issue it is not only one problem )
@@uavtech 16.9 fiexs rpm readings, but not glitches in flight. rpm reading was good on 16.8 may be even some older firmwares but in flight was problens even if you not using rpm filtering ( and it is not only pids)
Could you please help me and tell me if it would beneficial to put a 15V 100uF capacitor? I am getting some noise and I have one from an old tiny hawk board. Thank you.
Mate I fly 19500kv's on 2S on a Beta75-style frame. Motors don't get too hot with 80% throttle limit but - it's horribly shaky in AIR mode while flying pretty smooth in angle mode. Any suggestions for getting AIR mode smoother?
@@uavtech Needed a second to check but no, sliders are disabled. It's basically the Mockingbird tune for Tinyhawk v.4 ... I'll try using the sliders, thanks man.
Noop here. Love the US65 pro, thanx man ! Have a Problem that should be easy to solve for you guys: After some testflights with stock config that went well , I flashed BF 4.2.2 and this BLheli_M just as proposed in the video and used the given DIFF ALL from UAV Tech. I even noticed the increased flight time. ;-) !! only added horizon mode with airmode on.rest unchanged. (In Acro mode,also Airmode enabled). When I arm and fly in Angle mode, all works fine. however when I arm in horizon mode or Acro mode, the quad sits there idling for 2-3 seconds, then SOMETIMES (sometimes not) starts spooling up on its own (1-2 s) and then taking off rapidly, with throttle still all the way down (untouched). Indoors hits the ceiling hard and disarms. Any ideas what I messed up or what settings to tweak ? (...preferably without going through the whole flashing process again...?)
If you are min Anglenor Horizon, the quad should try to level on the ground. It it can't or the weight is really off, i-Term will wind up causing this behavior possibly? I have not seen this myself, would need to.confirm if that is what is happening.
Hi, this setup (copied to CLI) results in max load near 100% (tasks command), is this safe to fly? did you have any problem regarding overloaded CPU? edit: CPU is viewed by status command, and its 13%, so I guess Im OK :)
Yes, that's just an physical limitation with a gyro's accelerometer keeping the down reference and filter on the acc. data. You can raise the acc. filter in the CLI , but then more noise from the acc. comes into the PID loop.
Do u think I can start with this tune and filter settings for my 85mm 2s whoop running 1103 10000kv I mean obviously I’ll lower the p-d master multiplier to play it safe and slowly work it up ? Thanks
Hi sorry Im a noodb can you tell me you battery setup , i did everything I saw on the video and the drone has too much throttle input , even with throttle down it wants to fly off. Also a few seconds after battery warning it dies and i only get 2 min and 35 seconds flight time?
I have the same problems with BLHeli_M on Mobula6. Quad armed, motors spinning, but as soon I add throttle 1 or 2 motors stops and quad falls. Reflashed back to JESC 2.3 48kHz firmware and it's all good.
👍🏼 And thanks for showing us how to use bl heli config Mark. I’ve been usc jesc and paying for rpm filtering this whole time. I’m a little hesitant thought since I had issues with jazzmack with the crazybee board when the mob6 first came out.
# DIFF ALL (to paste into BF 4.2.3 for the US65PRO. This assumes you have BLHeli_M ESC firmware and FrSky RX
# feature
feature -AIRMODE
feature -ANTI_GRAVITY
feature MOTOR_STOP
# beacon
beacon RX_LOST
beacon RX_SET
# map
map AETR1234
# serial
serial 0 64 115200 57600 0 115200
serial 1 2048 115200 57600 0 115200
# aux
aux 0 0 0 1700 2100 0 0
aux 1 1 1 1300 1700 0 0
aux 2 13 1 1700 2100 0 0
aux 3 28 1 900 1300 0 0
aux 4 35 2 1700 2100 0 0
# adjrange
adjrange 0 0 1 900 1200 12 1 0 0
adjrange 1 0 1 1200 1800 12 1 0 0
adjrange 2 0 1 1800 2100 12 1 0 0
# vtxtable
vtxtable bands 6
vtxtable channels 8
vtxtable band 1 BOSCAM_A A CUSTOM 5865 5845 5825 5805 5785 5765 5745 5725
vtxtable band 2 BOSCAM_B B CUSTOM 5733 5752 5771 5790 5809 5828 5847 5866
vtxtable band 3 BOSCAM_E E CUSTOM 5705 5685 5665 0 5885 5905 0 0
vtxtable band 4 FATSHARK F CUSTOM 5740 5760 5780 5800 5820 5840 5860 5880
vtxtable band 5 RACEBAND R CUSTOM 5658 5695 5732 5769 5806 5843 5880 5917
vtxtable band 6 IMD6 I CUSTOM 5732 5765 5828 5840 5866 5740 0 0
vtxtable powerlevels 2
vtxtable powervalues 0 1
vtxtable powerlabels 25 200
# master
set gyro_lowpass2_hz = 375
set dyn_notch_width_percent = 0
set dyn_notch_q = 250
set dyn_notch_min_hz = 125
set dyn_notch_max_hz = 350
set dyn_lpf_gyro_min_hz = 300
set dyn_lpf_gyro_max_hz = 750
set acc_calibration = 27,-59,-67,1
set mag_hardware = NONE
set baro_hardware = NONE
set rssi_channel = 8
set serialrx_provider = SBUS
set dshot_bidir = ON
set motor_pwm_protocol = DSHOT300
set motor_poles = 12
set vbat_warning_cell_voltage = 300
set ibata_scale = 1175
set yaw_motors_reversed = ON
set small_angle = 180
set deadband = 2
set yaw_deadband = 2
set osd_warn_batt_not_full = OFF
set osd_warn_batt_warning = OFF
set osd_warn_esc_fail = OFF
set osd_warn_core_temp = OFF
set osd_vbat_pos = 2433
set osd_rssi_pos = 2362
set osd_tim_2_pos = 2423
set osd_flymode_pos = 2457
set osd_throttle_pos = 2392
set osd_current_pos = 2368
set osd_mah_drawn_pos = 2400
set osd_craft_name_pos = 2442
set osd_warnings_pos = 2345
set osd_avg_cell_voltage_pos = 353
set osd_disarmed_pos = 2314
set osd_stat_tim_1 = ON
set osd_stat_max_spd = OFF
set osd_stat_battery = ON
set osd_stat_bbox = OFF
set osd_stat_bb_no = OFF
set debug_mode = SMARTAUDIO
set vtx_band = 5
set vtx_channel = 1
set vtx_power = 1
set vtx_freq = 5658
set gyro_1_align_yaw = 900
set name = US65PRO
profile 0
# profile 0
set dyn_lpf_dterm_min_hz = 105
set dyn_lpf_dterm_max_hz = 255
set dterm_lowpass2_hz = 225
set p_pitch = 69
set d_pitch = 68
set p_roll = 63
set d_roll = 62
set p_yaw = 68
set d_min_roll = 0
set d_min_pitch = 0
profile 1
profile 2
# restore original profile selection
profile 0
rateprofile 0
# rateprofile 0
set rates_type = ACTUAL
set roll_rc_rate = 1
set pitch_rc_rate = 1
set yaw_rc_rate = 1
set roll_expo = 54
set pitch_expo = 54
set yaw_expo = 54
set roll_srate = 100
set pitch_srate = 100
rateprofile 1
rateprofile 2
rateprofile 3
rateprofile 4
rateprofile 5
# restore original rateprofile selection
rateprofile 1
# save configuration
save
Hi @UAVTech , Great Video.
D you have the standard AIO board ? I see that you have 200mW setting for the VTX but i think mine is limited to 25mW.
Instablaster
Thank you, it turned out great. I tried it on the de65pro with 19k motors on 1s, the native ones are faulty. Plus 1 minute flight time 4.30-4.50 vs 3-3. 20
Just done this and the quad flies awesome. Thanks
Very helpful. I love this quad and am playing with its setup. Thanks for the Diff all! I am going to try this this weekend and record some DVR. Also may upsize it to a 75mm frame. Also I know this was a little bit ago that you did this, but the GNB27 connector batteries work well and can be found may places including Amazon (GNB 300 and the GNB 450). I cut the battery try out and use a very light velcro strip for battery retention and that has helped a ton, as I was having the same sticker issue you were.
The connector is also availble from GNB (its the same) its called GNB 27
Good tip! Thanks!!
UAV Tech
Sure ;-) you help a lot more 😄
I couldnt find those on BG but ordered a set on Aliexpress. Always good to have stuff like this in stock
My De65 is still in transit. Cant wait to theow youre tune on there
This is a great review. Straight to the point and exactly what I needed to know. I have this whoop on the way and I look forward to applying all of your upgrades and PIDS. Thank you very much and I will let you know how it goes.
I couldn't find BLheli_m. Only 16.7 Official. Could you tell me in more detail how to get BLHeli_m?
Nevermind, I got it now. I had to update my configurator. thank you for putting this video up. I have learned a lot.
lordy lordy thank goodness for this walk through on this quad! I bet it'll sell like hot cakes and a trillion people will be looking for better tunes. great to have this available! GNB has had this connector out for quite a few months now - you can buy their batteries, but not from retailers yet AFAIK. Worth cautioning though that you can really make life inconvenient if you botch a BLHeli flash. New users should be really careful that the board has stable power while flashing - it's not like an aborted flash with an FC that you can just start over easily via USB. A power interruption during a blheli flash can mean you're committing yourself to some fine soldering so you're able to flash via the C2 method.
I still like PH connectors. Bah humbug! :-)
@@uavtech oh yeah! ... i actually think they're great, too. especially if you're using two of them like this 2S fairly low draw config and you're using the solid pin ones? super light - already a zillion chargers and batteries with that standard. not a lot reasons to switch for me!
I've gotten GNB 1s with GNB27 from Amazon in the states. I didn't use them though, since I've switched everything to XT30. I moved from PH2.0 because eventually the connectors are so loose they can't keep the quad in the air, with lots of little disconnects and reconnects.
Tested the BLheli_M now on a Cidora and it's 👌👌👌
Make sure to count the number of motor Magnets when setting up rpm filtering
@S Grim alright pro tuner ahahah
@@FailsafeFPV wut? Magnets is what more people will understand than "poles"
@@M.TTT. I was joking, I know what you mean, I've changed it now
@S Grim ahh
@@FailsafeFPV alls good mate, have a nice weekend, eh?
Those batteries are supposed to be compatible with GNB27 connectors and those are available on Amazon.
Thanks Man! Yep totally love this little thing but I had no Idea about the yaw washout. I thought it was a coanda effect or something of how these craft fly when I went for a steep descending dive. Keep in mind this IS my first whoop and didn't know any better about performance nuances for these. P.S. Did you mod the RX and VTX? 🤔
I did not mod anything. Is there a recommended mod?
@@uavtech Ah....I got little wire stubbies for the RX and VTX. It was hard to tell in your video bit it looked like you modded FrSky antennas for those modules. Perhaps they are upgrades from what I have.
I'm guessing if you ditched that frame it wouldn't yaw washout and fly better no matter the firmware.
Excellent
Hello ☀️
I just got my DE65 Pro today :-)
So I tried to flash blheli at the point 'Select version' it only shows the newest verion '16.7.1 [Official, beta]. How do I get '16.9'?
Edit: solved. I had the wrong configurator version 😏
This battery connector war is Ridiculous !! I don’t understand WHY WE DIDNT JUST USE THE DEANS MICRO T connector FROM THE GET GO . It’s been around for what a decade? We don’t need every company making there own connector. It’s Absurd. It’s making me hate all of my tinywhoops.
Wish i knew about them 2 years ago when converted mine to micro losi style. I like you can't think why we needed a new connector.
great video thank u
Good video! Have an issue with my 65 Pro I updated the firmware on mine and probably should not have. Does anybody have a backup of the .hex file for it?
Here in the UK I found a seller selling GNB et2.0/gnb27 for really good prices! Also I think it’s harder to put the batteries in with the r xsr version.
Can you share...
@@Z4nd3r-D sure, here’s a link:
www.ebay.co.uk/itm/233714163786
If you scroll down and see the seller’s other items you’ll see a bunch of other sized gnb27 lipos
Hey, what driver would I need to have for this drone? My computer doesn’t recognise it
Get the Impulse RC driver fixer: impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe
Pretty interesting, dude!!! 😃
Seems like a fantastic little quad!
Stay safe there with your family! 🖖😊
are RPM filters now working with jazz-maverick 16.9 esc firmware? i thought there was an issue that meant they would give problems
I test and compare many firmwares from jazz maverick and i think best is 16.77 48khz ... it is more stable than others. If you want rpm use dshot 300 .
@@t.me_hgjhghgf yea, i've set up rpm filters on 16.73 for whoops through 5" but was reading the forum where above 16.73 had issues. i just made all the changes here and it read 0 errors on motors, so i'm going to test it tentatively :)
@@Sully365 on my quads ( 3 to 5 inch) more stable maverick firmware 16.78 , others incl 16.9 have some glitches in flight , rpm reads issue it is not only one problem )
16.9 should be fixed up.
@@uavtech 16.9 fiexs rpm readings, but not glitches in flight. rpm reading was good on 16.8 may be even some older firmwares but in flight was problens even if you not using rpm filtering ( and it is not only pids)
Could you please help me and tell me if it would beneficial to put a 15V 100uF capacitor? I am getting some noise and I have one from an old tiny hawk board. Thank you.
Hard to say, but worth a try.
can i use the same configuration for mobula 7?
Mate I fly 19500kv's on 2S on a Beta75-style frame.
Motors don't get too hot with 80% throttle limit but - it's horribly shaky in AIR mode while flying pretty smooth in angle mode.
Any suggestions for getting AIR mode smoother?
P & D Balance at 1:1?
@@uavtech Needed a second to check but no, sliders are disabled.
It's basically the Mockingbird tune for Tinyhawk v.4 ...
I'll try using the sliders, thanks man.
Did you add the BLHeli M to the config or is there a newest firmware version that includes it? (looks like a new firmware)
BLHeli_M is a fork of BLHeli_S with more aggressive development going on at the moment.
@@uavtech ah okay, I meant the esc firmware version options in the drop down menus
Hey! couldyou help me? my de65 pro dont fly. it just get crazy throttle by itself. its a flysky version. thanks
Vibation issue. Look for the source.
Noop here. Love the US65 pro, thanx man ! Have a Problem that should be easy to solve for you guys: After some testflights with stock config that went well , I flashed BF 4.2.2 and this BLheli_M just as proposed in the video and used the given DIFF ALL from UAV Tech. I even noticed the increased flight time. ;-) !! only added horizon mode with airmode on.rest unchanged. (In Acro mode,also Airmode enabled). When I arm and fly in Angle mode, all works fine. however when I arm in horizon mode or Acro mode, the quad sits there idling for 2-3 seconds, then SOMETIMES (sometimes not) starts spooling up on its own (1-2 s) and then taking off rapidly, with throttle still all the way down (untouched). Indoors hits the ceiling hard and disarms. Any ideas what I messed up or what settings to tweak ? (...preferably without going through the whole flashing process again...?)
If you are min Anglenor Horizon, the quad should try to level on the ground. It it can't or the weight is really off, i-Term will wind up causing this behavior possibly? I have not seen this myself, would need to.confirm if that is what is happening.
Hi, this setup (copied to CLI) results in max load near 100% (tasks command), is this safe to fly? did you have any problem regarding overloaded CPU? edit: CPU is viewed by status command, and its 13%, so I guess Im OK :)
No good. Needs to be
what about crazy gyro after crash in angle mode? is still there or not?
Yes, that's just an physical limitation with a gyro's accelerometer keeping the down reference and filter on the acc. data. You can raise the acc. filter in the CLI , but then more noise from the acc. comes into the PID loop.
Sir, try the fus x111 pro from banggod please.. 🙏🙏
Do u think I can start with this tune and filter settings for my 85mm 2s whoop running 1103 10000kv I mean obviously I’ll lower the p-d master multiplier to play it safe and slowly work it up ? Thanks
Yup. Use it
Hi sorry Im a noodb can you tell me you battery setup , i did everything I saw on the video and the drone has too much throttle input , even with throttle down it wants to fly off. Also a few seconds after battery warning it dies and i only get 2 min and 35 seconds flight time?
Sounds like a vibes issue. Set filter sliders at 1.0 (both) and see if that makes it better.
@@uavtech that helped thanks, and how come I'm getting such short flight times ?? shouldn't it be around 4min and 30 sec? i tried 48 and 96 hz
Go with 48k and work the filter slider down. You should see flight times go up. Also, charge batteries to 4.35v. It is a switch on the charger.
@@uavtech thank you and tell me what should I set my min cell voltage, max , warning and capacity ? Thank you
What would you do with Tinyhawk 2 Freestyle on BF4.2.x?
Same, except a PD Balance slider at 1.0.
Can you share your setup please
Blheli_s jesc or m? Is m stable enough now?
Seems fine to me.
I cant Bind my us65 pro with my transis x9 Lite can Someone pleased help
Are you trying to bind D16 ACCST? Vs. ACCESS?
@@uavtech i tried both
Thanks dir your fast answer
Tried this configurator and firmware on my Mobula 6, just falls out of the air after 10 seconds.
That's odd. Works fine for me.
Same
I have the same problems with BLHeli_M on Mobula6. Quad armed, motors spinning, but as soon I add throttle 1 or 2 motors stops and quad falls. Reflashed back to JESC 2.3 48kHz firmware and it's all good.
@@ТЕХНАРЬ-с2й which version of betaflight are you running on your Mobula 6? Having all sorts of issues with 4.x...
@@Z4nd3r-D I had problems only when BLHeli_M was flashed. Betaflight 4.2.3 working great.
3:51 Answer to "What is BLHeli_M?"
👍🏼 And thanks for showing us how to use bl heli config Mark. I’ve been usc jesc and paying for rpm filtering this whole time. I’m a little hesitant thought since I had issues with jazzmack with the crazybee board when the mob6 first came out.
👍👀🇭🇷
Don't live in the past! We know who your talking about Mark :)
BF 2.0 FTW! LMAO. [rolling eyes]