Is your system monitoring from HMI, you can easily see the before opening encoder value from HMI.... What are the actual settings... Then you open and do maintenance or replace.... Then again you need to fix the servo motor and give the connection of the encoder also and then you compare with the previous Value.
Thanks it is not actually replacement , it is mounting. I mean mounting a encoder to the bldc motor like drone motors which hasn't got an encoder by factory default.
@10minutesengineeringsolution @jhonfredydaza1013 is asking if this encoder only needs to be installed in the motor shaft or if some programming is required after mounting the encoder to get the motor running. Thanks in advance for your help.
@MrFernandoBedoya.. Actually its very difficult to install but if you know the system it will be very easy for you,,, 1st you need to know the encoder counting number if you have any display with inbuilt that system, then you need to be aligned with your encoder as per your requirement when the system is well working.
Can i convert 110v servo motor to 220v? I don't k know what cause overheating but my servo white controller is 30amp, can i convert into different amp? Thanks
@@10minutesengineeringsolution i bought it from Aliexpress and they said a 110v servo motor with 30amp servo white controller is good combonation. Do you thik its true? Thanks
Need to align the encoder and roter by measuring motor pulse with the help of oscilloscope meter and dc power supply, otherwise, like this as shown in the video this motor will not work ! Please take caution before disassemble the servo motor!
So a question regarding the encoder, you said it needs to be put back in the same place - but what happens if you have a brand new stepper/servo motor? Would you need to open it up, or do you just put the value to "0" before starting it up? I would also recommend building a "stand" for doing maintenance/service on the stepper/servo motor, could help better.
Thanks for Your Question..... 1st if you need to open this encoder for repairing purposes you must need proper tracking or marking back cover side encoder Stand which place encoder is Fixed. If a little bit displaced from the original setting it will not be working. So be careful and need to mark properly when you Open.
thanks from Costa Rica .
Can you do this sick encoder programming?
Hi friend. Can you tell me that how can i align a quadrature encoder index to a custom bldc motor which hasn't got factory out encoder on itself ?
Is your system monitoring from HMI, you can easily see the before opening encoder value from HMI.... What are the actual settings... Then you open and do maintenance or replace.... Then again you need to fix the servo motor and give the connection of the encoder also and then you compare with the previous Value.
Thanks it is not actually replacement , it is mounting. I mean mounting a encoder to the bldc motor like drone motors which hasn't got an encoder by factory default.
For alignment of the encoder index and the stator flux of the motor properly
Waiting for similar another vedio
Very Very Informative
Thanks
Hola, excelente videos, tengo una pregunta, ese encoder se debe programar con el motor? O solo se instala y no se hace nada más.
Mmmm...hasta ahora no conozco encoders que necesiten ser programados,
Can you give me a message in English,,, i can't understand your question clearly please?
@10minutesengineeringsolution @jhonfredydaza1013 is asking if this encoder only needs to be installed in the motor shaft or if some programming is required after mounting the encoder to get the motor running. Thanks in advance for your help.
@MrFernandoBedoya..
Actually its very difficult to install but if you know the system it will be very easy for you,,, 1st you need to know the encoder counting number if you have any display with inbuilt that system, then you need to be aligned with your encoder as per your requirement when the system is well working.
Claro, yo trabajo con rexroth Bosch y los encoders se deben programar con el motor, de lo contrario no funcionan@@MrFernandoBedoya
nice job
Can u supply spares for this motor encoder and power connector
Types of encoder... Encoder information required & connector port or pin number or picture required for better understanding. And where are you from?
Good sir
@@kumara1974 Thank You.....
Can i convert 110v servo motor to 220v? I don't k know what cause overheating but my servo white controller is 30amp, can i convert into different amp? Thanks
Thanks for your question,,, but the result is not possible to convert to another option,,, its very sophisticated design for a specific point.
@@10minutesengineeringsolution i bought it from Aliexpress and they said a 110v servo motor with 30amp servo white controller is good combonation. Do you thik its true? Thanks
@@ji3200 it could be .... Because presently many other options are included in a single unit.
Rewind and conection
How to open the rotor
Can you please see the Video carefully,,, then u get an answer,
Need to align the encoder and roter by measuring motor pulse with the help of oscilloscope meter and dc power supply, otherwise, like this as shown in the video this motor will not work ! Please take caution before disassemble the servo motor!
Absolutely right
Ganti bearing apa harus ganti endkoder bro
Not understanding your question....
I am from indonesia. You speaking indonesia
@@mohefendy4148 Sorry i am from Bangladesh.... No Don't speak Indonesia.....
Why there is humming noise coming
Sorry for the interruption.. Next time I will solve this. Thanks
Your location for servo motor repair
Sorry sir,
I am an employee of Pepsi cola in Bangladeshi Plant.
Good inf
best
So a question regarding the encoder, you said it needs to be put back in the same place - but what happens if you have a brand new stepper/servo motor?
Would you need to open it up, or do you just put the value to "0" before starting it up?
I would also recommend building a "stand" for doing maintenance/service on the stepper/servo motor, could help better.
Thanks for Your Question..... 1st if you need to open this encoder for repairing purposes you must need proper tracking or marking back cover side encoder Stand which place encoder is Fixed. If a little bit displaced from the original setting it will not be working. So be careful and need to mark properly when you Open.
Hello bro I open encoder and I forget the actual position of encoder can U tell put back original position of encoder?
❤❤
Lene he
Need encoder
Send your detailed information about Encoder
@@10minutesengineeringsolution😂😂😂😂 mostly it not works
2 encoders replacing done... Successfully completed.
Rewind