I installed the Gomexus Power Knob on a Penn Spinfisher V. The knob works well,and spins freely. One thing that needs to be pointed out, is that the bearings are shielded, not sealed. If you dunk the reel, you will get water in the bearings. They are easily replaced, which helps mitigate the "crap" factor. As far as installation goes, I strongly recommend that you use a drill press or vertical mill to ensure proper alignment and minimize the risk of damaging the finish on the handle. "I recommend" really means "you better. Just my $0.02 worth.
What size spin fisher do you have? I’m looking to fit one of these to my spinfisher vi 2500 but not sure which size knob to get. Also I only have a hand drill so I’m a bit nervous about wrecking my reel
Another thing that needs to be pointed out is that you should put a washer between the reel handle and the 1st bearing to avoid loading onto the reel arm. The video just shows the bearing being installed but you can see they equip you with washers. I would use them. Additionally, cutting the handle off is a waste of time. I actually clamped the handle into the vice when I began drilling and it was fantastic. I hand drilled this starting with a good spring loaded center punch and then taking a little time to make sure that I punched close to the center of the pin and then started with a 3mm bit ensureing that i stopped occassionally to make sure I was still centered. Once I was down a little ways into the pin, i took out the 5mm (13/64) bit and drilled out the pin which took off the handle and finished out the hole for the new pin.
I followed all the Instructions and made a drill fitment. Now its on and all but the Knob itself does not spin freely and it is hard to reel and very awkward. What gives???
we have updated the shaft for a easy and better performance, please contact us via the channel you bought it, will send the new shaft to you free of charge.
Installed the A knob version today on my Nasci fcxg 4000, fits perfectly took less than 5 min to install.
I installed the Gomexus Power Knob on a Penn Spinfisher V. The knob works well,and spins freely. One thing that needs to be pointed out, is that the bearings are shielded, not sealed. If you dunk the reel, you will get water in the bearings. They are easily replaced, which helps mitigate the "crap" factor. As far as installation goes, I strongly recommend that you use a drill press or vertical mill to ensure proper alignment and minimize the risk of damaging the finish on the handle. "I recommend" really means "you better. Just my $0.02 worth.
What size spin fisher do you have? I’m looking to fit one of these to my spinfisher vi 2500 but not sure which size knob to get. Also I only have a hand drill so I’m a bit nervous about wrecking my reel
Another thing that needs to be pointed out is that you should put a washer between the reel handle and the 1st bearing to avoid loading onto the reel arm. The video just shows the bearing being installed but you can see they equip you with washers. I would use them. Additionally, cutting the handle off is a waste of time. I actually clamped the handle into the vice when I began drilling and it was fantastic. I hand drilled this starting with a good spring loaded center punch and then taking a little time to make sure that I punched close to the center of the pin and then started with a 3mm bit ensureing that i stopped occassionally to make sure I was still centered. Once I was down a little ways into the pin, i took out the 5mm (13/64) bit and drilled out the pin which took off the handle and finished out the hole for the new pin.
The music was very helpful.. Thank you
Installing the screw into the back of the rod, does it make the rod expand to pressure fit?
How to install on Shimano FX 4000 FC? Direct or drill installation? Thanks
I got a daiwa black widow 25a, what size would you recommend? And would it be direct or drill? Thanks in advance
Can you send your handle in somewhere for this to be done rather than doing it yourself?
thanks for the video. Will this work on the Penn Squall 15? Thanks in advance.
Sorry,it can't fit ：（
What size knob for a spinfisher vi2500? Also can I do this with a hand drill?
I’ve been using the drill instal ones for a few years and I’m not a fan of when
hooked up it will unscrew the whole knob off what’s up with that ??
It will be related to some accessories added during installation, but you can add some screws to fix
Nice info.. Thanks👍👍
I have a spinfisher vi 4500 which size of knob should I order??
You can choose 45mm knob, it's drill fitment for Penn spinfisher vi 4500. www.amazon.com/dp/B07MPDH1NZ?ref=myi_title_dp
Drill fit penn long beach 65? Also what size recommended? Thanks in advance
Hi, it's drillfitment for Penn long beach 65. You can choose 41 or 45mm size knob
Will these knobs fit on a Penn Battle II 5000?
Hi How r u? Thank you for your inquiry. It'll be drill fitment for Penn Battle.
@@gomexusfishingworld2608 Thank you very much.. do you know if I will need the 45mm or 47mm for this model?
@@kix-mi9it You're welcome. 45mm will be the right choice for you.
Good morning, For a Shimano FL 2019 4000XG : drilling install or direct install? if you have a link for purchase! please thank you
It's direct fit for Shimano FL 2019 4000. You can choose 38mm
www.amazon.com/dp/B07R3XYZQW?ref=myi_title_dp
@@gomexusfishingworld2608 Thank you for response😎
@@Eric-lb7ts my pleasure :)
Shimano baitrunner 3500b direct install or require drill?
it's drillfitment for baitrunner
Daiwa BG magsealed 4000 drill Fit size please 38-41?
Hi, you can choose 41mm size knob to direct fit
Is there one that wilI work with a Cabo PT SE 40?
It's drill fitment for Cabo PT SE 40, you can choose our 38mm knob
Below is the link you can choose: www.amazon.com/dp/B07R3XYZQW?ref=myi_title_dp
Thanks. What about spinfisher vi 4500?
@@joelsantana8116 41mm or 45mm knob is better, you also need to make a drill
Any of these fit for a penn fierce III spinning 4000?
It's drill fitment for penn fierce
Drill size for Large size on daiwa?
Drill size is 5mm or 6mm, it depends on which type knob you decide to order.
Ive installed it already all good mate. Thanks
mucho pomo pa poco carrete
I followed all the Instructions and made a drill fitment. Now its on and all but the Knob itself does not spin freely and it is hard to reel and very awkward.
What gives???
we have updated the shaft for a easy and better performance, please contact us via the channel you bought it, will send the new shaft to you free of charge.
Gomexus Tackle will this knob fit on a shimano sedona 4000fe? And if so is it the same method of installation?
Just back the screw off a hair.
why must people add annoying music to these