Hermano siempre sigo tus videos,tus conocimientos ayudan mucho a soldadores como yo y siempre con esa humildad tan caracteristica que tiene. Saludos desde argentina!
Thanks for the explanation and flawless technique; a thing that i would like to point out is the fact that with shorter tungsten it seems that you have more heat input due to the angle and probably the lower travel speed, if you look to the color the 5mm tungsten bead is kinda blueish, while the other 2 are goldish. I may be wrong but to me this means that with 10 and 15 mm tungsten you have a more proper gas coverage and less heat input in the workpiece
@@weldHAGOJIBI i'll be waiting for it, I learn a lot from your videos, they are very interesting and entertaining; plus you are a very humble and it's something I really appreciate👍🏻
Amigo eres todo un experto en proceso tig me gusta tu forma de explicar gracias x compartir tu conocimiento en materia d soldadura saludos desde fco Rueda tabasco mexico
Man, this is just what I was looking to have answered and this guy did a fantastic job of explaining! I have watched some of his other videos and this guy is pretty darn good. Interesting that he uses a percentage of the "outside" diameter whereas I was taught using the inside diameter. I personally like a medium tight weave or pitch. Just seems easiest for me on my wrist and arm. I usually stick out the id distance (number of cup in 16ths) except for the root. I will shorten that about a 16th of an inch to point inwards to center of pipe a bit more. Otherwise he is right that it really is a matter of personal preference and comfort level. Love this guy's tutorials tho. Very informational.
The biggest thing here is he’s also not using 2 pieces of metal and tossing the weld under a chop saw to show you the penetration. The more angle you have away from vertical, the less heat you’re putting into penetration, which is bad for thick material, but very handy if your getting down into gauges (22ga instead of say 1/8” plate). He talks about it, but he should have done a chop on each plate to show the difference. It all matters and changes upon material thickness and type. There’s also something to be said about how your argon will perform under high angles…. you better crank up the gas if you’re running that much stick-out. He’s a pretty good welder from the few videos I’ve seen. I too was taught using inner cup diameter and most welding I do is basically “stick-out equals I.D.”, but sometimes I toss a ton out with a huge gas flow to get into a tight corner, or I suck that baby way in to get a good weave and penetration.
@@ЮрийДж Если честно я аллюминий варил всего несколько раз и в основном вылет был такой же как и всегда. Такой тонкий я даже не варил. По этому не берусь давать такие советы.
@@ЕгоровАлексей-м3р сегодня попробовал выпустить вольфрам до 5мм. Управлять швом стало на порядок проще. Около часа пробовал разные настройки, подобрал более/менее что-то подходящее, но появилась проблема с самим вольфрамом. Заточки стало хватать ненадолго. Кончик быстро крошится и за день я его почти весь сточил. Щас пересматриваю ролики и ищу есть ли тут что-то об этом. Но в общем мне понравилось
If you maintain the same angle of the torch the tungsten length will not change he puddle size or shape. The angle with which you grind the point on your tungsten will have more effect on puddle size and shape. A long narrow needle point will have a larger puddle that a short pointy cone.
Adoro seus vídeos o melhor do UA-cam tô aqui 3 horas da manhã assistindo 😅 quando a gente gosta do que faz não tem hora certa 😂😂😂 Seus vídeos são maravilhosos obrigado por compartilhar seus conhecimentos 👏👏👏👏
Excelente, como siempre sus videos con de alto conocimiento y aporte para nuestro aprendizaje . Le agradezco mucho por su tiempo para realizar estos trabajos en videos . Muchas gracias y mucho éxito en su vida .. algún día llegaré a ser un profesional gracias a sus enseñanzas y ponerlas en práctica. 👏👏👏
Great videos! After 30+ years you always show me something or confirm what I've been doing. At 230 amps you're going to get penetration. But how much does tungsten angle affect how deep it is? Your videos do a great service for welder new or experienced. Thank you very much. Please keep them coming. Ol Sparky
밝은금색이 더 고품질에 가깝죠. 사실상 눈으로 용입되는걸 보고 간다면 어떤색이던 상관은 없습니다. 산화만되지 않는다면 파란색계열이 입열량이 작은거고 그만큼 용입이 안될 확률이 높겠죠. 그렇다고 색으로 판단은 하면 안되겠죠. 붉은색이 진해지다 거무스리해지는데 파랑계열과 다르게 입열량이 많아진다 소리라 색으로 비교할 필요는 없지만 적당한 전류와 위빙속도가 적정한지 판단하는 최소한의 척도쯤은 될 수 있을거 같습니다. 큰 의미는 없습니다
Excelente muito bom gostei e foi de grande ajuda suas explicações e tudo mais, seu detalhamento é exelente, vou seguir vc e aguardo mais conteúdo nesse sentido,
@@wiltonmarcos7403 это вопрос воспитания. Этикет не разрешает использовать узкопрофессиональную речь при широкой аудитории. Это допускается только в узком кругу специалистов. Есть новички, которые купили сварку вчера. Они могут что-то не понять. Он воспитанный человек
Nice job , ever run the Arkansas bell hole ? Yrs ago I tig the roots from boiler tubes, pipe and triple X main steam line . Never walked the cup always free hand left n right hand . Times have changed . Nice crown on inside ! Great I are sharing techniques!
The word for welding beads seems to be different for each country and region. Perhaps a weld bead and a weld seam are sometimes referred to interchangeably.
I also wanted to see welding on ferrous metal and aluminum. And it’s interesting to know the brand of the rod. Which rod should be used for different metals????
Hello. It would be nice to check the depth of the penetration with the difference in the angle setting. Theoretically, the linear energy should be greater at a less acute angle ...
@@weldHAGOJIBI Thanks for the answer, I just watched your video regarding penetration depth. You explained it is very well. Nothing more nothing less. Great knowledge and skills. You could easily have your own private welding school. Regards from Poland
![weld [HAGOJIBI]](http://yt3.ggpht.com/ytc/AIdro_lButtTy6bwshHHOdUuuc7ktsddm0YgRj2FhqoPUm3aQA=s48-c-k-c0x00ffffff-no-rj)
티그용접 3개월차 배우고 있습니다 막연하게 느낌적인것들을 이해하기 쉽게 딱딱 요약해서 올려주셔서 정말 많은 도움이 되고 있습니다.
감사합니다
Наконец то я вижу грамотного учителя, каналов по сварке много, но этот канал мне очень понравился
Hermano siempre sigo tus videos,tus conocimientos ayudan mucho a soldadores como yo y siempre con esa humildad tan caracteristica que tiene. Saludos desde argentina!
Cuál crees 5, 10, 15 fue la mejor opción
오늘도 유익한강의 감사합니다ㅎㅎ
막연히 느낌만알고 명확히 설명은못하던부분들이 제대로 정리되는느낌입니다!
Que dice?
Thanks for the explanation and flawless technique; a thing that i would like to point out is the fact that with shorter tungsten it seems that you have more heat input due to the angle and probably the lower travel speed, if you look to the color the 5mm tungsten bead is kinda blueish, while the other 2 are goldish. I may be wrong but to me this means that with 10 and 15 mm tungsten you have a more proper gas coverage and less heat input in the workpiece
Thanks for the great comment. We plan to make a video about it in the future.
@@weldHAGOJIBI i'll be waiting for it, I learn a lot from your videos, they are very interesting and entertaining; plus you are a very humble and it's something I really appreciate👍🏻
@@raulduke85 Thank you. Have a nice day.
@@raulduke85 ua-cam.com/video/qY3VXxzIjOY/v-deo.html
Longer stickout just means tge argon is protecting the cooling bead for longer thats all
Hiện tại mình đang học hàn , nếu ngày mai qua được mối 4G hàn hồ quang thì mình bắt đầu học hàn tig. Video này giúp ích mình rất nhiều. Thank ad
شكرا جزيلا لك لقد تعلمت منك الكثير من خلال متابعة فيديواتك . تحية لك من القلب 🫰❤️
Спасибо за подробные обьяснения 👍очень интересные и полезные видеоуроки по сварке👍
La verdad un gran soldador y me ayudaste mucho increible saludos desde argentina,un gran profesional
Real master of welding .
Best teacher of welding .
Огромное спасибо! Вы делаете очень хорошие и полезные видео.
ОН 230 АМПЕР НАКРУТИЛ?
@@Капитан_Очевидность да , там же написано
Excelente video m ayuda muchísimo, sos una buena persona por compartir tus conocimientos a los demás, desde Argentina un fuerte abrazo!!!
Excellent video! Clear, concise, and well made! Thanks so much for sharing!!
Amigo eres todo un experto en proceso tig me gusta tu forma de explicar gracias x compartir tu conocimiento en materia d soldadura saludos desde fco Rueda tabasco mexico
Best welding channel on YT! ❤
Man, this is just what I was looking to have answered and this guy did a fantastic job of explaining! I have watched some of his other videos and this guy is pretty darn good. Interesting that he uses a percentage of the "outside" diameter whereas I was taught using the inside diameter. I personally like a medium tight weave or pitch. Just seems easiest for me on my wrist and arm. I usually stick out the id distance (number of cup in 16ths) except for the root. I will shorten that about a 16th of an inch to point inwards to center of pipe a bit more. Otherwise he is right that it really is a matter of personal preference and comfort level. Love this guy's tutorials tho. Very informational.
The biggest thing here is he’s also not using 2 pieces of metal and tossing the weld under a chop saw to show you the penetration. The more angle you have away from vertical, the less heat you’re putting into penetration, which is bad for thick material, but very handy if your getting down into gauges (22ga instead of say 1/8” plate). He talks about it, but he should have done a chop on each plate to show the difference. It all matters and changes upon material thickness and type. There’s also something to be said about how your argon will perform under high angles…. you better crank up the gas if you’re running that much stick-out. He’s a pretty good welder from the few videos I’ve seen. I too was taught using inner cup diameter and most welding I do is basically “stick-out equals I.D.”, but sometimes I toss a ton out with a huge gas flow to get into a tight corner, or I suck that baby way in to get a good weave and penetration.
@@BlackwaterDSM Good points mike, thank you!
아주 소중한정보 감사드립니다
숙제가 생겨서 좋습니다
항상 잘보고 있습니다. 최고의 용접선생님이십니다.
갈수록 설명이 누구나 알아 듣기 수월해짐이 느껴지네요^^
언제나 유익한 내용 감사합니다!
ua-cam.com/video/qY3VXxzIjOY/v-deo.html
Your tig welding skills are extremely impressive. I mostly do flux core welding at my work, with some stick/tig at smaller intervals.
Shoot tig is where the moneys at for sure, especially aluminum
溶接の仕上がりまで芸術にするのはホントプロのこだわりですね。ブラボー！
A true Grand master at tig welding great video thank you.
와 티그용접 2주차인데 정말 좋은 자료입니다. 나는 한줄 떄우는데도 왜이렇게 오래걸리나 했더니 텅스텐을 5mm보다 3배나 뺴서 오래걸렸던거였어 ..
Здравствуй Джин! Отличное познавательное видео! Раньше не предавал значению вылету вольфрама ставил на глаз примерно 7-10 мм! Спасибо за опыт.
Здравствуй брат. На мой взгляд, я также в основном использую 7 ~ 10 мм. Может быть, многие люди похожи.
Я варю аллюминиевые трубы толщиной 1...2 мм, вольфрам синий, вылет 0мм. Это неправильно?
@@ЮрийДж Если честно я аллюминий варил всего несколько раз и в основном вылет был такой же как и всегда. Такой тонкий я даже не варил. По этому не берусь давать такие советы.
@@ЕгоровАлексей-м3р сегодня попробовал выпустить вольфрам до 5мм. Управлять швом стало на порядок проще. Около часа пробовал разные настройки, подобрал более/менее что-то подходящее, но появилась проблема с самим вольфрамом. Заточки стало хватать ненадолго. Кончик быстро крошится и за день я его почти весь сточил. Щас пересматриваю ролики и ищу есть ли тут что-то об этом. Но в общем мне понравилось
Show, muito bem explicado , um dos melhores canais de solda. Obrigado.
오늘도 너무좋은 정보감사드립니다...다음기대됩니다
Как всегда очень наглядно и понятно. Спасибо
ua-cam.com/video/qY3VXxzIjOY/v-deo.html
Muito obrigado seus vídeos estão me ajudando muito professor
More great knowledge and beautiful welds from a Master of the trade thanks HAGOJIBI 👍👍👍👍👍
This video so very helpful for begginers like me.thank u sir.i watch all videos a lot.
I hear temperature can change the colors that appear. It would be interesting to see this test redone with a temperature read on the different welds.
gracias por la gran ayuda que brindas en tu canal! saludos desde argentina
Thank you .
Спасибо огромное Вам за очень полезное видео .
Probably the best detailed channel. Very well recorded and shown. Thanks
ua-cam.com/video/qY3VXxzIjOY/v-deo.html
유익한 정보 감사합니다
정말 귀에,눈에 쏙쏙 들어오네요 ㅎ
망구 제 생각 입니더 ㅎㅎ
감사합니다 🙏
당신은 당신이하는 일을 아주 잘합니다. 브라질에서의 인사
추석 연휴 즐겁게 보내셨습니까? 파이널 연습중인데 텅스텐 길이가 고민이였는데 너무 감사합니다.
감사합니다. 연휴 마무리 잘 하셔요~^^
Спасибо Джин.Всегда интересно смотреть твои видео,.👍
Thank you bought welding yesterday ... I will study. 👍
Thank you for sharing your knowledge in english.
텅스텐 길이조절이 중요한것을 이제 느끼고있습니다
길이조절에서 토치각도가 변화되고 그속에서 용융풀이 변화차이가 용접에 큰영향주고 그것을 얼마나 숙련됨에따라서 기량차이가 나는것같습니다
과학적입니다
感谢师傅的详细讲解，感谢。
Спасибо друг ! Как всегда всё очень наглядно и познавательно (-:
If you maintain the same angle of the torch the tungsten length will not change he puddle size or shape. The angle with which you grind the point on your tungsten will have more effect on puddle size and shape. A long narrow needle point will have a larger puddle that a short pointy cone.
Ai sim mestre está uma bela aula e apresentação de como se faz diferente formas de soldagem na regulagem do tungstênio obrigado pela apresentação 🇧🇷🙏
I am not a welder, but really enjoy your knowledgeable and interesting video ...
Adoro seus vídeos o melhor do UA-cam tô aqui 3 horas da manhã assistindo 😅 quando a gente gosta do que faz não tem hora certa 😂😂😂
Seus vídeos são maravilhosos obrigado por compartilhar seus conhecimentos 👏👏👏👏
Gracias maestro por enseñarnos su técnica saludos y bendiciones.
Cómo siempre muy buenos videos gracias por la esplicasion sigue así 👍
Excelente explicación, muchas gracias por compartir tus conocimientos
와 와 와 와 와 와 와 !!
비드가 왜 이렇게 좁게만 나올까 했는데
알고리즘으로 이게 딱 떠서 바로 해결했어요
대박 감사합니다 ㅠㅠㅠㅠ
Excelente, como siempre sus videos con de alto conocimiento y aporte para nuestro aprendizaje . Le agradezco mucho por su tiempo para realizar estos trabajos en videos . Muchas gracias y mucho éxito en su vida .. algún día llegaré a ser un profesional gracias a sus enseñanzas y ponerlas en práctica. 👏👏👏
ua-cam.com/video/qY3VXxzIjOY/v-deo.html
Best presentation TIG welding technic I have saw!!!! Congratulations!
Hail Brazil !
You the best welding !
Реально, полезная информация.
Sei molto bravo nelle tue spiegazioni , imparerò da te , grazie
انا بعشق المهنه دي واتمنى انك تفيدني بالفيديوهات بتاعتك واتمنى من ربنا انه يعطيك الصحه
Great videos! After 30+ years you always show me something or confirm what I've been doing. At 230 amps you're going to get penetration. But how much does tungsten angle affect how deep it is? Your videos do a great service for welder new or experienced. Thank you very much. Please keep them coming. Ol Sparky
We will be making a video on penetration in the future. Thank you.
ua-cam.com/video/qY3VXxzIjOY/v-deo.html
좋은 영상 잘봤습니다. 배우는 단계인데 도움이 될것같아요 ^^
Thank you. You are an excellent instructor!
Parabéns por suas explicações ......ajuda de mais na qualidade das soldas que faço
harika videolar cok şey öğrendim türkçe altyazılar için teşekkürler istanbuldan selamlar
많이 배우고 갑니다...용접결함 관련 용어나 결함 사진이나 영상도 부탁드려도 될까요?^^특히 RT 결함 관련된 거 있으면 부탁드릴께요.용접사라면 어떤결함인지...용어나던가... 본인이 용접사라면 알아야 될꺼 같아서요..부탁드립니다.^^
심심해서 댓 답니다
p:기공,이물질,등등 결함
lf:융착불량
ep:빽 과다
rc:빽 빨림
uc:파이널이나 빽 양쪽끝이 꺼질때 rc랑 비슷
frc:파이널 두줄이상일때 피드와 비드 겹침에 계곡이 심할때
rt결함은 위에 것들이 대 부분
-지나가는 접사가-
@@한철진-q1l 오~몰랐던 용어도 있네요...감사합니다.^^
Excelente, Muchas Gracias, Saludos desde Nicaragua,,,
영상 잘 봤습니다
궁금증이 있습니다
1. 5mm와 15mm 두개를 비교 해보면
비드 색깔이 다른데
어떤 색깔이 더 고품질인지 궁금합니다
2. 5mm와 15mm를 비교 했을때 텅스텐 각도에 따라
입열량도 달리질거 같은데
어떤 길이에서 입열량이 더 적은지
궁금합니다
단정짓긴 어렵지만 단순히 색으로만 본다면 밝은 금색이 더 좋습니다. 글로 쓰기에는 내용이 너무 길것같습니다. 그에 대한 내용을 차후에 영상으로 만들 예정이에요.
@@weldHAGOJIBI 기대하고 있겠습니다냥 !!
밝은금색이 더 고품질에 가깝죠. 사실상 눈으로 용입되는걸 보고 간다면 어떤색이던 상관은 없습니다. 산화만되지 않는다면
파란색계열이 입열량이 작은거고 그만큼 용입이 안될 확률이 높겠죠.
그렇다고 색으로 판단은 하면 안되겠죠.
붉은색이 진해지다 거무스리해지는데 파랑계열과 다르게 입열량이 많아진다 소리라 색으로 비교할 필요는 없지만 적당한 전류와 위빙속도가 적정한지 판단하는 최소한의 척도쯤은 될 수 있을거 같습니다. 큰 의미는 없습니다
@@야옹야옹-w5z ua-cam.com/video/qY3VXxzIjOY/v-deo.html
@@슬리퍼-x4t ua-cam.com/video/qY3VXxzIjOY/v-deo.html
Excelente muito bom gostei e foi de grande ajuda suas explicações e tudo mais, seu detalhamento é exelente, vou seguir vc e aguardo mais conteúdo nesse sentido,
용접은 한국이다 역시
Complimenti per il video molto utile per i principianti,come me,avrei preferito la traduzione delle impostazioni della saldatrice Grazie
Esto es algo que mi cerebro ocupa cada mañana gracias
Thanks, sangat membantu... 👍👍👍
Show de bola mano velho vc manja muito!!!!
Parabens...
Se ele fosse bom ,te falaria que essa distância se chama stkaute
@@wiltonmarcos7403 это вопрос воспитания. Этикет не разрешает использовать узкопрофессиональную речь при широкой аудитории. Это допускается только в узком кругу специалистов. Есть новички, которые купили сварку вчера. Они могут что-то не понять. Он воспитанный человек
@@wiltonmarcos7403вы тоже не знаете что такое просак😂
Great knowledge, I assemble machines for processing bread food and production, very useful, thank you
Perfeito essas solda meus parabéns 👊🇧🇷
진심 유익했네요 감사합니다
very good
영상 감사합니다 즐거운 하루되세요
Awesome video. I even learned heard some words like “tungsten”👊
Nice job , ever run the Arkansas bell hole ? Yrs ago I tig the roots from boiler tubes, pipe and triple X main steam line . Never walked the cup always free hand left n right hand . Times have changed . Nice crown on inside ! Great I are sharing techniques!
Друг, ты - лучший! Я мечтаю научиться варить железо так же, как ты.
Thanks for sharing this video, could I ask what is the difference between weld bead and weld seam?
The word for welding beads seems to be different for each country and region. Perhaps a weld bead and a weld seam are sometimes referred to interchangeably.
@@weldHAGOJIBI Got it, thanks for your explanation.
@@amberzhang3170 ua-cam.com/video/qY3VXxzIjOY/v-deo.html
Great video. Didnt understand you but the visual was a perfect explanation! 🙏
there are some subtitles in different languages
Beautiful
Thank you very much, creator. I benefited a lot from you
Gracias por tu información amigo.
ua-cam.com/video/qY3VXxzIjOY/v-deo.html
👍👍👍ARIGATO GOZAI MAS SENSEI VERY GOOD TEACHING ! SENSEI YENI RAY ! HOUSS !!!
고맙슴니다 새해 복 많이 받으세요
Thanks for the useful technique
감사합니다
매번 많이 배우고 갑니다...
혹시 sch80 6g 영상도 올려주실수 있으신가요.
육지자세도 배우고싶습니다.
ua-cam.com/video/qY3VXxzIjOY/v-deo.html
도움이 될 것으로 생각이 드네요 감사합니다
excellentes videos!
I also wanted to see welding on ferrous metal and aluminum. And it’s interesting to know the brand of the rod. Which rod should be used for different metals????
Thailand. Thank you.
Hello. It would be nice to check the depth of the penetration with the difference in the angle setting. Theoretically, the linear energy should be greater at a less acute angle ...
The content about it was uploaded yesterday.
@@weldHAGOJIBI Thanks for the answer, I just watched your video regarding penetration depth. You explained it is very well. Nothing more nothing less. Great knowledge and skills. You could easily have your own private welding school. Regards from Poland
@@freedomofspeech9323 ua-cam.com/video/qY3VXxzIjOY/v-deo.html
많은 도움이 됩니다. 감사합니다
لحام جيد جدا
من فضلك أن ترينا اسهل طريقة لتعلم لحام المشي على الكأس،حركة اليد مع الذراع
شكرا
نحن نخطط لعمل فيديو حول هذا الموضوع في المستقبل.
ua-cam.com/video/qY3VXxzIjOY/v-deo.html
좋은 자료 감사😊
Thailand. Thanks you
Très bonne vidéo, peux tu faire une vidéo sur la soudure quart à quart avec pénétration en épaisseur 3 ou 4 mm ?
Voulez-vous dire un tuyau de 1/4 pouce?
Jak zawsze ciekawy film , pozdrawiam ;)