@@DCWERX I had to do hours and hours of research and looking at diagrams to just to find out my car my didn't have one then I had to do more research on running the car on the distributor
How come you put the first resistor in r11 and then cut to you soldering it into r10? Very confused I thought your meant to put them in the exact area labelled on the bag ?
Hello, thank you fir your examples. I'm looking with a dual staged injectors on a v6. Is there a way to attatch a daughter board for a second stage inje tkr system
When assembling, for example if I’m doing the first pack of resistors, do those resistors need to go to a specific place or do all resistors in one baggy work universally with every resistor labbled on the bag?
Does anyone know can this ecu speeduino any vers run a inline 4 cylinder PSA TU5jp4 engine in sequential order. Cause therese a trick to this particular engine. There is not any camshaft position sensor for this and the OEM ecu uses special coil pack to run this engine sequentiall ignition . But i do wanna get an after market one
When assembling, for example if I’m doing the first pack of resistors, do those resistors need to go to a specific place or do all resistors in one baggy work universally with every resistor labbled on the bag?
Hi I have a miata NA 1.6. 1990 I have installed a 30-0300 x-series wideband 450cc injectors . the car works fine, I just have to keep the laptop connected the engine stops if I do not use the laptop it looks like it's losing ignition because dashbord clock not working when does that after it stops it starts very hard. but it works at only idle if I want to leave the engine dies again can be the sensor on the clutch pedal because I can't use the option to decelerate fuel cut off. if I activate it, it does the same thing as with the laptop disconnected if you can help me thanks
Sounds like multiple issues. If you are using a PNP Speeduino Miata ECU then the 5v supply may be faulty. Contact the seller for warranty or replacement. As for the hard start and TPS issue, that may be tune related if all else is good.
Speeduino is an open source product so support is provided by the community. Outside of that, you should contact whoever you bought your ecu from, for support
Depends on which board you go with, where you buy it and if you want it assembled or not. They start at around ~$100 for board + components and go up as high as ~$250 assembled. You can get them from the speeduino store, wtmtronics, diyefi, eBay and a few other sellers
I just built my 1st ECU. I couldn't have done it without your tutorials. Thanks from the uk
You welcome bud.
Do these spediunos work on 4 cylinder cars, like mx5 ?
@@DCWERX Do these spediunos work on 4 cylinder cars, like mx5 ?
Bro you are really talented with the tuning aspect always glad to see content from you
Thank you
@@DCWERX no prob at all I just admire you work bro bless up ✌
@@CULTUREMUSIK I appreciate it man 👍
my MAN!! excellent assist
Wish I could solder as neatly as you 👍great video
Thanks. It took me a bit of practicing to get to that point. After 3-4 boards you get much better
Thanks so much for this dude! Saludos desde Argentina!!
well done !
It should be noted that the 0.4.3d (and later) boards the polarity of the LEDs are reversed and so is the MAP sensor.
thanks for the video
Huge help much love!
Glad it was helpful
Thank you dog very helpful 🙏
Thanks for Schooling us
You should make a video on trigger wheels and ignition settings I'm sure it will get millions of views
What exactly about trigger wheels and settings would you like to see ?
@@DCWERX like how where to find your trigger wheel and how many teeth you should put in or if you don't have a trigger wheel what you should do
@@DCWERX I had to do hours and hours of research and looking at diagrams to just to find out my car my didn't have one then I had to do more research on running the car on the distributor
I see a ton of people needing help with idle on the speeduino and cranking
@@darthbolloful great idea. That sounds simple enough to put a video together covering the subject
I think it took me 4 hours. While I'm not an expert at it, I have populated boards before. For practice, I bought a DSO oscilloscope from Amazon.
4 hours is decent. Depends on how distracted I am, it me takes 3-4 hours
Thanks, is Brazil!
BUENÍSIMOOOO
Thanks !
Very useful.
thanks for sharing
Thanks for the video is really helpful
looks like fun very interesting thankyou
If I was a woman I would marry you. I'm joking but, TY so much man. No words to describe
Geniuss!! 🤩🤩
Hello friend, a question, the kit of components to solder on the speeduino pcb? Could you provide me with the list? thanks greetings
How come you put the first resistor in r11 and then cut to you soldering it into r10? Very confused I thought your meant to put them in the exact area labelled on the bag ?
Hello, thank you fir your examples. I'm looking with a dual staged injectors on a v6. Is there a way to attatch a daughter board for a second stage inje tkr system
When assembling, for example if I’m doing the first pack of resistors, do those resistors need to go to a specific place or do all resistors in one baggy work universally with every resistor labbled on the bag?
If your kit came from a reputable seller, every component should be labeled, so you know exactly where they go
Hi. hello where do I buy a board 0.4 for soldering very thanks,I'm from slovakia
Does anyone know can this ecu speeduino any vers run a inline 4 cylinder PSA TU5jp4 engine in sequential order. Cause therese a trick to this particular engine. There is not any camshaft position sensor for this and the OEM ecu uses special coil pack to run this engine sequentiall ignition . But i do wanna get an after market one
Hi. Whats the difference between the board 04.3 version B to version C? Thanks and congratulations for your good work!!!
When assembling, for example if I’m doing the first pack of resistors, do those resistors need to go to a specific place or do all resistors in one baggy work universally with every resistor labbled on the bag?
Hi, do you know whether i need the stepper motor driver for pwm idle control?
Hey one question can we use 5.6v 2w instead if 5.6v 3w zener!!?
When running a 0.4.3 on a d16 an uln 2003 needs to be used in order to have a working fuel pump?
Yes
Hi I have a miata NA 1.6. 1990 I have installed a 30-0300 x-series wideband 450cc injectors . the car works fine, I just have to keep the laptop connected the engine stops if I do not use the laptop it looks like it's losing ignition because dashbord clock not working when does that after it stops it starts very hard. but it works at only idle if I want to leave the engine dies again can be the sensor on the clutch pedal because I can't use the option to decelerate fuel cut off. if I activate it, it does the same thing as with the laptop disconnected
if you can help me thanks
Sounds like multiple issues. If you are using a PNP Speeduino Miata ECU then the 5v supply may be faulty. Contact the seller for warranty or replacement.
As for the hard start and TPS issue, that may be tune related if all else is good.
Ok. I'll talk to them thanks a lot
great video.... what case is that and where can I get one? thanks.
It's a case made by Hammond. You can get it at wtmtronics.com
Can you pls assets me to get in contact with speeduino.Nobody is replaying me.
Speeduino is an open source product so support is provided by the community. Outside of that, you should contact whoever you bought your ecu from, for support
how much is the speeduino standalone ecu. and where can i order it.
Depends on which board you go with, where you buy it and if you want it assembled or not. They start at around ~$100 for board + components and go up as high as ~$250 assembled.
You can get them from the speeduino store, wtmtronics, diyefi, eBay and a few other sellers
Yeah I see on eBay for 220. How much u charge to tune .my car is a b18c civic . You probly know it .
Do you make a plug an play for a 1995 subaru?
Currently I don't.
Wtmtronics
Hallo
where could i purchase an assembled speeduino
There are a few resellers across the globe but I recommend the Speeduino store, wtmtronics, speedyefi, diyefi and the other authorized resellers
@@DCWERX i need to do one for my m52 e36 turbo project
@@rype36 I think someone makes a pnp speeduino for the m52. Check out the Speeduino forums for details
Hello and thank you for this useful video. But you don’t talk about the wideband controller. I have no idea how to plug it 😂