Aftermarket barrel with new keys - ebay.us/YASfq9 New Ford Ignition lock barrel set - OE Part number 2363729 Check Euro car parts - tidd.ly/3lIO7xA (use discount codes on site) Check "Car Parts for Less" - tidd.ly/2LNEwIn (use discount codes on site) Tools used : Amazon / eBay links Small snap on flat blade screwdriver - ebay.us/S62oNB Needle nose pliers - amzn.to/3b3RZWu
You’re a legend for making this video! Thank you! I’m going to build one of these as a spare to keep in my glovebox for when it inevitably fails! You’ve save me a lot of money 👍
Thank you for making this, have been looking into this since my old ignition lock barrel was changed and thrown away by the previous owner, and it doesn't work with the same key. So glad I finally found some kind of advice/tutorial on how to do this.
Fantastic video. You have saved me hours of work and stress. Thank you very much. First time i've done one of these. Took me a couple of hours but worked first time with your instructions. Regards Peter
Great video , took my old one out and unassembled it to write the numbers down . On mine had to put in position 1 to get the pin to push in to remove and replace from the ignition housing. Cost me £90 for a new lock much cheaper than waiting for it to completely fail. So cheers again saved me a few hundred quid 👍
Just did it. Would have been lost without it.I matched it with excising numbers. So much easier, other than the kit didnt have 4. 4 only 4.3 etc. Still worked. Please not. When pulling the key out. The pegs cant be depressed. I was holding it tight so the pegs didnt pop out. Hold it slack in the hand, so key comes out. It will make sense to anyone doing it. Thank You
Hi, Thanks for the vid! My ignition barrel locked today, leaving me unable to rotate the key.. Could you let me know please, does this mean I can't remove the faulty barrel as you show in the last minute of this tutorial?
Brilliant thank you. Just to speed things up can you write down which number clip comes out of which slot and simply replace with that number or does that not work? A video on getting the barrel out of the car would be good as well ❤
Hi mate its me again 😂, ive got a customer in next week with Transit, he went away and someone tried stealing the van ,snapped a spider key in barrel 😳, i know to remove the barrel you need a key and turn it to press pin,what shall i recommend him if i cant remove barrel fo you think? New steering lock and ignition?
Arr what a pain! Yeah you may be able to drill it out , I’ve had to do it before , just pre worn him it may need a full new lock / barrel if you can’t get it out
Aftermarket barrel with new keys - ebay.us/YASfq9
New Ford Ignition lock barrel set - OE Part number 2363729
Check Euro car parts - tidd.ly/3lIO7xA (use discount codes on site)
Check "Car Parts for Less" - tidd.ly/2LNEwIn (use discount codes on site)
Tools used : Amazon / eBay links
Small snap on flat blade screwdriver - ebay.us/S62oNB
Needle nose pliers - amzn.to/3b3RZWu
Saved my ass at the end mate 😂😂 with 1 minute till closing time i got it done.
Nice one 👍👍
You’re a legend for making this video! Thank you! I’m going to build one of these as a spare to keep in my glovebox for when it inevitably fails! You’ve save me a lot of money 👍
Nice one , glad it will help mate 👍👍
Thank you for making this, have been looking into this since my old ignition lock barrel was changed and thrown away by the previous owner, and it doesn't work with the same key. So glad I finally found some kind of advice/tutorial on how to do this.
👍👍 glad to hear it helped
Fantastic video. You have saved me hours of work and stress. Thank you very much. First time i've done one of these. Took me a couple of hours but worked first time with your instructions. Regards Peter
Great video , took my old one out and unassembled it to write the numbers down . On mine had to put in position 1 to get the pin to push in to remove and replace from the ignition housing. Cost me £90 for a new lock much cheaper than waiting for it to completely fail. So cheers again saved me a few hundred quid 👍
Glad it helped! thanks for the comment 👌👍
Thanks for the video, as Ford claimed there weren’t instructions for this but they also couldn’t build it this saved me 👍👍
👍👍
Just did it. Would have been lost without it.I matched it with excising numbers. So much easier, other than the kit didnt have 4. 4 only 4.3 etc. Still worked.
Please not. When pulling the key out. The pegs cant be depressed. I was holding it tight so the pegs didnt pop out. Hold it slack in the hand, so key comes out. It will make sense to anyone doing it.
Thank You
Cheers for this video, my ignition barrel failed this was perfect to help me rebuild mine.
Nice one , glad it helped and thanks for the comment 👌👍
Thank you, mines started being a pain its sticking every so often the key has to go in a certain way to operate the lock. i think its on its way out.
Great video! Clear information and simplified very well thanks
Thanks 👍
How do you know which number pin goes where? Is it because you stripped down the old and copied that?
Thank you for doing this video!! Any tips for how to get the old barrel out if the key doesn’t turn please?
👍 arr yeah that can be abit tricky! I’ve had to drill one out before
Hi where did you get the berulub fr16 bechem from for the lock Thanks for great video
Thank you I learnt a lot from this video👍
Glad it was helpful!
Would you make this same instructional video but with a tibbe lock? Please and thanks!!!
👍 I will if I get a chance
Hi,
Thanks for the vid!
My ignition barrel locked today, leaving me unable to rotate the key..
Could you let me know please, does this mean I can't remove the faulty barrel as you show in the last minute of this tutorial?
Yes I’m afraid it might be quite tricky to remove mate , may need drilling out
Brilliant thank you. Just to speed things up can you write down which number clip comes out of which slot and simply replace with that number or does that not work? A video on getting the barrel out of the car would be good as well ❤
Yeah you could do that if you have the old ones split ready , if I get the opportunity I will do 👍
Hi what grease do you use for wafers?. Thanks
Great tutorial helped me a lot thanks
Glad it helped! thanks for the comment
Thanks good video, bought the kit from Ford's main dealer charged 80 quid and there was only 6 small springs and no number 13s bizarre!
Glad to help 👍👍 that’s odd!
Vielen Dank, hat mir sehr geholfen. Grüße aus Deutschland
Nice one , thanks for the comment 👍
Do you have a link to where I can get the wafers from please
Can't seem to find em on Ebay so will be ford only now, you can get a built up barrel quite cheap now.. ill attach a link ebay.us/YASfq9
Hi, does it matter about matching the bottom numbers to my original lock numbers?
I can quite remember to be honest mate , it was a while ago I did this and not done 1 recently
Podias decirme donde lo compraste.
Y decir el orden de leer las celdas?
From ford direct mate , think you might beable to get complete build up barrels off eBay now though
Great video
Thanks!
Great video. Thanks. Just done my No problem 👍🏻
Glad it helped
Hi mate its me again 😂, ive got a customer in next week with Transit, he went away and someone tried stealing the van ,snapped a spider key in barrel 😳, i know to remove the barrel you need a key and turn it to press pin,what shall i recommend him if i cant remove barrel fo you think? New steering lock and ignition?
Arr what a pain! Yeah you may be able to drill it out , I’ve had to do it before , just pre worn him it may need a full new lock / barrel if you can’t get it out
good vid. well done
Thanks for the comment , much appreciated 👍👌
Amazing thank yoy
Thank you too!
@diydaly saved my day best video on ford barrel yet amazing keep it up👌👌
@@dariusdmg2157 👍👍
*👍👁🇷🇺*
👌👍😀 thanks for the comment