How to replace Water Pump Toyota Corolla. Years 1990 to 2002
Вставка
- Опубліковано 25 лип 2024
- How to replace water pump Toyota Corolla years 1990 to 2002
Cómo reemplazar la bomba de agua Toyota Corolla años 1990 a 2002
1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002
Engine types:
1295 cc 2E I4
1331 cc 4E-FE I4
1452 cc 3E I4 (Van)
1496 cc 5E-FE I4 (Van)
1498 cc 5A-FE I4
1587 cc 4A-FE/4A-GE I4
1587 cc 4A-GZE SC I4
1762 cc 7A-FE I4 - Авто та транспорт
Did Toyota deliberately design this engine to make replacing something so simple extremely difficult or what? I've replaced a few water pumps before but have never seen anything like this in all my 55years of life. Thank you for making this video because without it I don't think anyone would be able to diy.
Thank You 👍
Of course they did.
Peter Finn the best english and mechanic teacher in the world! Thanks from Brazil Friend!
Great 😃
4AFE one of the best engines ever made. GOOD JOB!
Yes. Thanks for info. :-)
Why do you say that?
@@bassheadlife492 because I made 900 000 km whit that engine whith no problem
@@Alexo945 how about the transmission?
@@bassheadlife492 two time main bearings
step 1 - remove engine
Hahaha
Thanks Peter! As always you pay attention to every detail.
Thank You for Your feedback. :-)
Great video.
thank you for making this video . its done very well . i must point out that here in america , we have a cartoon character named " boris badenov " . you sound just like him .
Good. 😃👍
Gracias Peter,, me ayudó mucho.
👍
my new favorite guy to watch ,step bye step nice job
👍🤠
Very good diy,I learned a lot thank you
Many Thanks for comment. :-)
Now i sit and wonder why i was too lazy to change the pump when i changed the timing belt... Like i diddn't change the clutch release bearing when i changed the transmission....... Damn it!!!!
Thanks too! I have also a toyota corolla. I replace my timing belt today. Congratulations for the patient and very detailed explanation! Thank you again!
Portugal
Nuno.
Thanks for comment. And greetings to soccer Ronaldo too :-)
thanks for this Peter ...
Thank you
Thanks for comment 👍😀
Most of cases the engine is in the car when you need to replace parts..
Nobody will take out motor for replacing a water pump...i have exactly that car with this engine
Thanks
water pump failed with 10,000 miles left due to o-ring gasket not being replaced correctly,or removing old ring completely from inside o-ring crevice,instead of placing new o-ring on top of old one. Thanks Finn.
Thanks for feedback. 👍😀
Question did you setup the timing mark before or after removing the timing belt?
After and Before
WOW What a job and a pain in the a$$. I think I will look into a water pump delete next time I have my timing belt done on this car. Would be easier to install an electric water pump so that I can replace that easily in the event it fails. Who the hell wants to go through all of this? I bet the repair would be expensive!
Thank you for your message. I have read your message. 😀👍
I changed water pump, timing belt.. but my belt to the power steering and water pump is loose how do i tighten belt ? Does the alternator put tension on that belt to power steering?
The video is very good, very educational and explanatory, it explains how you should not do it.
👍
on a 1994 you need to take the engine mount arm that is hold by 3 bolts to the engine, as water pump slydes out/in that direction. this is working on the car...at first i did not take arm off, i got it out but was not able go put it back in. once i remove the engine arm it took me a few seconds to slyde it back in. remember do not bolt the pulley as you need it to move it atound to bolt the waterpump. then lift the engine until you can bolt the pulley to the pump one bolt a time ( jus grab the pulley with a pressure pliers use a piece of rag or carton to not scrash the pulley.) and bolt it one at the time.
my engine is a 5a and i had a used 7a water pump and it will not fit untill i cut a peace of aluminion off it. it fits fine and works greate.
Thanks and noted 😊👍
Do I have to lift the engine up to get water pump out?
Hi, No. You can replace it without engine lift.
Probably want to loosen the wp pulley bolts before taking off the belts if you don't have access to impacts, you can use an end wrench and large screw driver but it's slower
Thanks ! 👍
is it normal for coolant to come out of my overflow hose on the coolant reservoir on my corolla the car don't over heat and it only do it sometimes. do you think I'm putting too much coolant.
Hi, it is normal.
1) if you overfill coolant, it will eject excess coolant through the overflow
2) If you have air in the system, possibly you need to bleed the system or you have a failing radiator cap which is not holding the correct pressure and allowing coolant to flow to the reservoir prematurely.
hi peter..can use inpact wrench on this job?
Yes
yes...it's so easy to get at water pump WITH ENTIRE ENGINE OUT OF THE CAR!....lol do it with the engine still in the car.Go ahead & try to remove the pulley...YEAH RIGHT! I just did it with engine in the car with a friend.Had to leave water pump pulley on,take 12mm & 10mm bolts out of water pump casting,using engine hoist to raise/lower engine to get at bolts with a wrench.then pry on engine at where engine mount bolts onto engine towards drivers side as my friend wiggled out the water pump out of the 1 inch or 2 of space to do so....
Thank You 👍😁
My '97 Corolla appears to have a water pump leak. I am planning on getting it replaced. The current timing belt has about 45,000 miles on it. Is it worth replacing the timing belt at the same time or should I just replace the water pump?
Thanks for comment. 👍😀
How long does a bomb has of use life? this because i have a corolla 2015 and i only has 73 000 KM with the original and I have already have to change it?
Hi, this was use in 200 000 miles.
I know it's self explanatory, but you still should've mentioned to mark the timing points on the cam gear and crank atleast BEFORE REMOVING THE TIMING BELT... Jesus...
Ok
Hi.
Why do you rotate the camshaft twice with the belt on? Whats the significance of those two clockwise rotations? 🤔
Check settings
@@PeterFinnTheCarDoctor I dont understand?
My car is overheating, i dont know if its a water pump or the fan radiator...temp goes up in traffic but it goes down when un run in a hi way...what do you think is the problem?
Hi, easy Job ! Replace new radiator first. Then water pump.
Radiator is new
Then thermostat replace ! What car and model you have ?
Ae92 i remove the thermostat long time ago...tropical weather
Hi! Thanks for your video. I have a 4A-FE and the little rubber pipe near the water pump has broken. Do you know the diameter of the pipe? Tks
I have to find engine...👍
@@PeterFinnTheCarDoctor, Tks!
@@PeterFinnTheCarDoctor My friend, I have already found the dimensions of the flange. Do you have a video of how to change the shock absorbers of the Corolla 93-97? Where? Thank very much!
What a nightmare having to pull all that off just to get to that one bolt under the timing cover.
And there i was thinking it would a simple job to replace it.
Thanks 👍😀
to fasten the harmonic balancer bolt all you need is to turn the pulley bolt wile the spark plugs are in. that forse is enough, do is a couple of times.....the pulley and bolt turn in same closed tighten direction so bolt will never come loose....this is for people with no tools ok, if u have tools use them. and fallow the doctor orders. and to loosen it, look for video on you tube to loosen it with no tools. i done it many times it is safe.
Thanks and noted 😊👍
I was going to do this myself...mechanic wants to charge only $100 including the pump so i will let them do it
Great !
did the engine start?
Yes
1.5 engine?
1.6
Is this a Non-Interference engine????
Yes
Peterr is it possible to replace the water pump on a 91 camrry without taking the engine out? XD
Yes, maybe
Anybody can remove a water pump from an engine that sits on the floor why don't you show a video of doing it while it's in the vehicle so people can see how to remove it out of the
Noted
22:27 Selfuse.
He having hard time trying to take parts off .what a dope try doing it when the motor still sitting in the engine bay like us real mecanic
Crankshaft bolt is the hardest bolt to take off in the motor industry. It's clearly this guy does not a real mecanic
Yes, the Bolt is Hard.
My engine runs at a normal temperature, but my gauge goes to Hot when it is at normal temperature? Have you had this problem?
Yes, you have a issue. Temp must be in normal level. Check coolant level and thermostat
Peter Finn the Car Doctor I took the thermostat out to check flow. I used a thermal gun to check temperature. Everything is running normal. Temperature from gun shows normal. My gauge says it’s hot. But temperature is 144 degrees Fahrenheit?
Peter Finn the Car Doctor thank you. I found the issue. I had a loose connection between the battery and fuse box, which caused an interference with the temp sensor and cooling fans.
@@patrickrhodes8227I have that exact issue right now. Gonna try what you did and see if it works.
You did not show the method steps to reinstall the water pump and skipped over those steps?
Good comment 👍