The THW still exists, it is a civilian volunteer civil defence unit. They are well equipped and well trained and supplement the regular civil emergency services. They have every sort of vehicle from fire appliances, command and control units, heavy duty road cranes, demountable pumps and even canteen vans.
I operated one of these until 3 years ago and did some repairs and rebuilds and stuff. So feel free to ask. If you are going about 60km/h in 6th gear full throttle, it may be you are in low gear. Changing gears is somewhat tricky sometimes, it may stick in low gear even if the lever is on the left. What you need to do is pull the lever even more to the left, you should hear the air cylinder doing something. If it's sticking, drive the thing, go full throttle, pull the lever to the left and hold it, lift the trottle and back to full throttle. It should shift, if not do it again. Or try to get in in low gear, to make sure where you are. The knob in front of that lever is the middle diff lock. The rear diff lock is the knob right side near the steering column. It would be interesting where it has been in service.
Thanks a lot! thats very helpfull. and pretty much confirms how i figured the levers for the transfer-case, work :) But it doesn't feel stuck in low range (if so, those are some extemely high, low range gears.) i was able to get it up to speeds of 80-90 km/h. But it just took a really long time. And on gear changes, when i hit the max speed in one gear, and then canged to the next, it barely had enough power to pull in that gear. So it really felt like i just couldn't give the engine enough throttle. But i still haven't looked into the whole ting, any further :) Oh, and from the little documentation i have, i seems this served at a depot, in Suderlügum. and was last registered there, in 2016.
@@KJOff-Road/videos 90km/h means it's in high gear, for sure. It's high speed, maybe it will make 92 or 93. So fuel issue it is. There was no THW in Süderlügum, but in Niebüll. Maybe from somewhere else and second life in Süderlügüm. I couldn't find anything.
That would be such a good starting point for a camper build. Off-road capability and a sturdy functional box. There are many of these still around, see if you can sell the box to a fellow Magirus owner at least.
@@KJOff-Road When you have the box off just place it in a barn and use it as a tool box. Crib up to the chassis height, and you have a nice new secure tool storage.
The problem with the engine rpm is likely to be the governor on the injector pump. If the seaĺ goes bad on the rear of the pump it causes a hydraulic problem that stops the governer from opening up.
i drove that type of Truck at THW many years ago 🙂 the trottle problem looks like a swamped diesel filter or the diesel HP pump (nned some maintenance) BTW: the "shut off button" is meant as trottle-brake
Suggestion Remove the shelf's Keep the side folding platform and modified it so the "blue panel" could fold down (some named it 3way) IMO it will make the "flat bed" more practical Also that workinglamp somewhat feels soo coolll
That stop button in front of the seat, is the exhaust brake. But it also works as a stop button. Mercedes used the exact same mechanism, until the late 80:s. I drove a 10 cylinder Mercedes 1932 tanker truck for many years. Same setup, and the VDO gauges and warning lights were very similar. Even the steering wheel.
My 2 cents: careful how you build the roof rack. The noise it makes at highway speed can bring about a lot of regret. But all in all great find. Put the box on a utility trailer for towing dirt bikes, tools and sleeping quarters, what have you, for off road adventures .
German guy here. If you can't get it sorted in your place - maybe I can help. I shortly looked into it: With a buying contract (has to have the VIN in it) German KBA (Kraftfahrt-Bundesamt) should be able to provide the neccessary documents for a small fee.
Ich habe auch schon geschrieben, dass ich mich im Zweifelsfall mal mit meiner Zulassungsstelle diesbezüglich unterhalte. Die Daten müssen ja da sein. Wäre traurig, wenn der Lkw nicht wieder auf die Straße kommt.
@@KJOff-Road Hi, I live in Sweden and had a similiar issue with an former German Ikarus buss. You need to get in touch with the local office too the city where it was registered. There is no central office that has registration documentation in germany it all handled locally. If you have the german numberplate number that helps point you at wich office you need to contact. otherwise i would try taking contact with the THW becouse they probably have documentation on it.
@@KJOff-Road With the THW license plates there are some things to know. Because there are a special organisation, the KBA (Kraftfahrt Bundesamt) can't help you. The vehicles are registered via the THW registration office at the Procurement Office of the Federal Ministry of the Interior. I'm from Germany as well, please get in touch to me, If needed. BR, Martin
Not a camping person, but the tray looks like it has heaps of possibilities and would be a great camper. Remember seeing a few Deutz on the roads down under many, many years ago. The yankee stuff put paid to serious numbers on the road. See an odd one here and there. Have fun, stay safe and win the paper war.
@KJ Off-Road Hi KJ, German guy here who spend quite some time of his early life on THW and those rigs. As already said there is nowadays a centralized license plate „THW- on the actual THW trucks. But they changed the system quite some time ago for all THW , Police , Katastrophic Services and similar agencies Trucks and cars. Even sometimes Fire Trucks. With different letters of course: e.g. the letters from the normal car plates for the capital of the german sub-country (Bundesland) like for example in Hesse the capital is Wiesbaden meaning all police cars in Hesse have „WI- plates. Makes shifting vehicles from one stationary to a different one a piece of cake. That explained here comes the trick for you: BEFORE that centralized practice those Trucks had real local Number plates like any other vehicle. This means your truck probably had TWO number plates in his life meaning two sets of paperwork existed. What you have to do is search the complete vehicle for remaining hints of those number plates, because with having multiple trucks if the same loaded goods and gear we have put frequently the number plate data (or a shortage of that) on the gear and multiple places in that truck. Basically everything removable that could be misplaced after cleaning offsite of these trucks needed to be identified to put it right back. Also: inspect carefully the driver and passenger door. There must have been a time when „THW Ortsverband must have been signed in big letters on that doors. This „Ortsverband …“ means something like Stationary. So, with information of the old first number plate and the city name you look up the actual contacts of the THW of that city and ask them for the favor of a copy of that old paperwork. I know they keep goid records, especially the little ones like the one i was in. If you only get the last THW-123456 Number plate you ask in the THW facebook group for a contact of the city name. You want to find the job role „Schirrmeister“ of that years after the manufacturing date of that truck to hit the jackpot of person knowing EVERYTYhYiYnYg of that truck because it was his duty. And add a year when asking because sometimes they had the new trucks up to a year in stock coming from the manufacturer until all x-dozens of them where produced and then they rolled them out in the new version all at once to the different Ortsverband to make no-one jealous that the other ones already got the new truck. THW people are nuts about their special vehicles and proudly show them off knowing every tiny detail if it - like fire fighters who are the same kind. So as soon as you can name the plates and Ortsverband for specific identification it will be possible to find a person giving more details. Good Luck! Peter
Personally, I'd keep the side platforms, as it will make tying down whatever load you have on it a *lot* easier. I'd love to have something like this to build into a camper, actually, but I very much doubt I'll find one here in the US. Great find, and I wish you the best of luck getting it registered.
Put the box on the back of an old mercedes chassis - perfect for loads of craftsmen. Double your money? I love that the double cab is just two singles welded back-to-back You'll need to get a type-approval document from the manufacturer - if that is possible, then you might be going somewhere! Lovely project.
Sir that's a super nice work truck. Greeting from Murika. @25:50 It's a diesel it probably has a govener limiting it, it really sounds like 17-1800 rpm to me, that wouldn't be out of the normal. I'd think 2500 would be too fast for that engine to spin, most older diesel engines are booking it at 2 grand
Hi Kasper in my experience you can't go past a sleeping berth, it's just so nice to be able to stop driving late at night and climb into bed. I'm looking forward to seeing what you do with this gem.
O yes. I know the sound off those air cooled Deutz engines so well. As a much younger bloke I served in the South African defense force. " yes South Africa did have a proper defense force back in those days. " and they're vehicle of choice was the Magirus Deuts. And yes, I was a driver. Fantasticly well built old trucks.
Known as SAMIL and SAMAG. South African license built magirus trucks. South Africa only imported a small amount of actual magirus Deutz trucks. Around 2500 units if I recall correctly. How ever produced around 16 000 SAMAG, SAMILs locally.
@@spotty4710 The SAMAG and SAMIL all used ADE engines though, the Deutz engines were only used in those branded Magirus, and also in aircraft tractors and such, along with use in the fire engines on all bases. The tractors used the Deutz engines, a Borg Warner automatic truck gearbox, and a modified Mercedes differential, along with a prop shaft that was basically 2 universal joints welded together, as the tractor was that small. But with it all being made from bent steel plate, thinnest being 6mm steel as covers, and then going to the chassis, made from 25mm steel plate welded to make the U channels and such, so that you had a 16 ton aircraft tractor, locked forever into first gear with a pin. Those were wicked fast on take off, though when they were involved in accidents, invariably the damage was to what they hit, and possibly a new coat of yellow paint on the tractor. I did rebuild one that caught on fire, memorable in that they used every fire extinguisher in the area on it before the brigade arrived. not worried about the tractor, but because of what it was towing when the wiring loom caught fire.
It is a nice color Olaf, now i want one of those that box simply gave me so many ideas it would be awsome to convert into a explorer vhecicle the box allows for that making the kitchen and stuff acesseable from the outside and in the middle enough for a bed and bathroom simple awesome, plus lots of rom on the cabin.
@@KJOff-Road Trust me, im a professional backseat youtuber 😂. it is time for you finally have some color in your fleet i know that deep matte blue is a bit to take in but give it some time for your eyes to adjust to it and you will find it not so bad. Also i dont know if you read my other comment about a rev limiter or the mechanism being stucked on low gear and the leaver being disconected somehow. BTW hows the shed renovation going? :)
german THW (federal agency for technical relief = blue) or fire trucks are always a good sign, low kilometers and still regularly checked and maintained
what a beautiful and clean country...and what a cool vehicle with so many possibilities...GL on chasing the paperwork..let us know what ideas you plan asap..
Interesting that you were allowed to drive it home. I live in Croatia and have an LDV Convoy van I used to move my stuff from UK in 2011. I've been doing some welding to get it back in roadworthy condition but again I'm not sure if I will be allowed to register it on Croatia plates.
Had this brand of truck when I was H.G.V.1 driving back in the 80's you could always rely on this no matter what, good old double bunk plenty of room when away for 6 weeks on jobs in its day a good truck to have.
I did a little research, and that truck has the Duetz F6L413 engine, which is a 4 stroke 9.6 L. V-6. It appears to be turning plenty fast RPM-wise (max is 2300 at WOT), but someone else mentioned the little lever between the seats as being for either a 2 speed axle, or the splitter for a secondary gearset in the transmission. Most likely, you were stuck in low range through the whole trip! If it's anything like the control valve for the PTO, it's probably worth looking into. I love the design of the body on that thing. It would be perfect for a tool truck at a racetrack, or for on site heavy equipment service!😉👍👍
I was in the South African Defense Force in mid to late 70's and drove a 10 ton long nose Magirus there. Cannot remember the vehicle Description numbers but it was one of the most reliable vehicles I've ever driven.
The truck is so old with so few kilometers on the clock... it hasn't even had the "major inspection" yet, the problem with the "speed" could be that the injection pump needs an oil change because old oil becomes "sticky" over time. The problem (which someone else posted) with the leaky seal on the pump comes from "many kilometers driven", but with less than 50k on the clock it is more likely "swamped oil" so that the pump cannot turn on fully. (I speak from experience, because many mechanics don't want to do this oil change because it is a huge mess)
100% agree . Strip out the rear body and turn it into living space . Aluminium sheet where the side roller doors are . Insulate with celotex sheet materials . Solar on the roof . Honest it would make a fantastic camping vehicle . Much nicer than sleeping in the back of the cab . Nice truck .
Great little truck. Pity the storage setup on it doesn't suit your needs, it's clearly well built and very functional. It needs to find another truck that needs it.
First time viewer. Haven't checked your other videos yet, but think that box would make a fantastic mobile service box for working on cars/trucks. Set on a trailer, it would leave the tow vehicle free to run for parts, supplies, or lunch !
DEFINITELY KEEP THE DROP DOWN SIDES !!! you will kick yourself if you get rid of it !! As to lack of RPM ? .. could it have a rev limiter ?? Ether Mechanical ore electrical ?
I used to drive a Maggy Deutz 8 wheel tipper. Great bit of kit not the most powerful but that Air-cooled engine was so reliable. It never gave us any problems. Not the quietest engine and it had its own peculiar sound. But us Drivers loved them..
Hi, and I like your new truck. Here In the Uk, older trucks like yours are converted into Stock Car transporters with the crew cab ideal for family and mechanics to all ride along to race meetings. Anyway, good luck With your registration paperwork.
Starting it in 5th to break the clutch loose is going into my Farm-Fix memory bank. Subscribed. Also I have a Deutz BF6L913 I am going to put into my 1976 Ford F250 (I'm American) soon here.
Nice catch! It really is a shame to remove this cool bed, maybe make it a camper unit and just hitch the trailer behind for hauling 😉 Regarding the paperwork, I would start with the German TUV, with the 1 part of the German document you might be able to get the other part? Good luck and keep us posted! 👌🏻
Congratulations on the acquisition of the ex-THW Magirus. Unfortunately, I didn't watch the video earlier. Here is my tip: There is a website (in German) on which thousands of historic construction machines are presented and discussed, including many ex-THW vehicles. You may be able to get help there. The latter will perhaps come quicker if you register there and introduce the vehicle. As YT generally don't like links in comments, I will send you the link by email to the address you provided in this thread. Good luck
@@KJOff-Road The Magirus Deutz 170D11 is a widespread model that is also used by many fire brigades in addition to the THW. Both areas are known for the fact that vehicles are kept in them for a long time, especially as both fire brigades and the THW have plenty of opportunity to maintain their equipment when not in use. One more thing about the THW: The Federal Agency for Technical Relief (THW) is the German civil defence and disaster control organisation of the Federal Government with volunteer helpers and full-time employees in the portfolio of the Federal Ministry of the Interior and for Home Affairs. The higher federal authority has its headquarters in Bonn-Lengsdorf. The THW was founded in 1950 and has been a federal agency under public law with its own administrative substructure since 1953. The Federal Agency for Technical Relief is therefore a higher federal authority. The THW has local branches in almost every municipality. The equipment with vehicles and other devices is quite comprehensive. They are not a chip shop. The Magirus model under discussion is already quite old. Since ex THW vehicles are widely known for their good condition, quite a few have found their ways to small fire brigades or into private hands. Accordingly, the concerning knowledge should be widely dispersed. The spare parts situation should not be particularly tight either. You just have to find both. Unfortunately (for you) the whole area mainly takes place in German language. In special cases, however, I'd like to help with the research. In such cases, please send me an e-mail to the address you know. I wish you continued success. All the best
Uncle used to run a fleet of these things as dump trucks not this particular model bur the same engine. They where used as snow plows over here in the Highlands of Scotland 6x6 you couldn't kill them😊
I could be wrong but usually that button at your foot you pressed to stop the engine is actually called a decelerator, its used to retard the engine exhaust when travelling down long hills, it helps slow your vehicle down without overheating the brakes especially when carrying a heavy load..! Hope this helps
Always wanted one of these or a bullnose mercedes 1113 for a camper build. Love it. Looking forward to more videos. Good luck sorting out the paperwork.
You could keep the box and put it on a slight foundation ... to use as a "tool shed for outside" (garden hoses and so on) ... and as a "sunroof sitting lounge". That way you still have it in case you want to "go on a safari".
That Box would make an ideal base for the construction of a camper, and with those step sides it opens up possibilities for slide outs or canvas extenders to increase the usable space, along with the under body boxes for storage etc, even if it is not used on the current chassis
Dude can you show me the NATO jumper connector at some stage, if you think of it please, interested. I spent near 200 euros on some 350 amp andersons for my winch and , well thats too much! Lovely truck. I dont know jack about those air cooled engines, never seen one, very interested to know more, find it hard to comprehend how it would keep cool under load. That IFA was a beaut. Great content.
Thanks! And yeah, that is definetly too much! The round Nato style connector are usually more expensive than the "Anderson" connectors. and even then, a set of nato connectors should only be about 100-150 euro.
Cool truck, very useful. That bed has got to worth something to someone, it should help to offset the cost of the truck if can sell it to someone who wants to build a service truck. Hope you get the paperwork sorted, I am sure you will have some subscribers who will help you out😀👋🇬🇧
Hej KJ. Gammelt jern kan man bedre stole på end det moderne med elektronik. Jeg har betalt depositum for en Volvo Viking 4X4 Ex mili fra 1863. At hente den bliver en tur på ca 800 Km. Sjov at se din beretning. Tak
Kaspar, I thought getting imported vehicles registered in Australia was hard, we have it easy, no need to find history etc for it, so long as the numbers match the export/import documents no sweat. a tray keepin the drp down side platforms and a ramp would to me be ideal and use the box as tool storage and centre aisle of the box as somewhere to store long lengths of steel, and when you showed the middle on left side of the box instant location for a decent compressor. my thoughts but hey I'm Aussie. Pete
@@KJOff-Road I recognize the blue/white paint on the truck. This was from THW of Germany, a civil defense service team. Germany also has a dedicated water rescue team known as the DLRG.
It shouldn't be too difficult to get remade German THW paperwork from the THW itself or the road authority where she was stationed back in her active THW-time I reckon. Biggest issue might become that everything needs to be in German, officially translated and/or officially seen and approved by a notary. You might even get a full history of maintenance and repairs, should they have taken that on micro-film before selling her. Crazy archives in most of those places in Germany.
i suggest a sleeping cabin where teh backseats were and a storage unit in teh center of teh vehicle and then ANOTHER sleeping compartment with a fold OUT tent system at teh end like a caravan camper . the center storage unti should have folding out cooking stations for small meals so u can BBQ in teh wild ^^
GKW I. It has a winch. Used to drive the thing a for a while in the early 2020s. The only disadvantage is the ventilation - you wont see anything if you have people with wet clothes in there with you.
It sounds like the governor is sticking at high RPMs. A little Marvels Mystery oil in the oil for about 30 minutes and then an oil change might solve the problem. The box might be a good idea to keep and modify. It would hold a vehicle and keep the vehicle from the weather.
Is there really an issue with the engine? When you liftes the cabin I could not see a turbocharger. If that is true the engine would probably not go over 2000 RPM. The sound ofthe engine at around 26:00 seems to support this. Before you undertake some big repiairs you may want to check the datasheet. The sound remeinds me strongly of our old Mercedes 407 from the Red Cross. This engine didn't have a turbolcharger either and the range of RPMs was very low too.
Olaf the truck may have a rev limiter, i know now adays companys put a speed limiter of 90kmh on trucks so maybe it was some kind of rev limiter since it was a rescue truck maybe it could be used as a auto tanker and later converted to a utility truck i dont know just look out for a rev limiter or maybe its just stuck in low gears and the leaver is not connected or just falling apart. but good color choice
Nice truck. Which year is it? You didn't even tell us. The 4wd is permanent with a center diff, right and only the rear locker? I As for the registration I am not sure if the KBA can really help you with this. They can probably confirm that it is not stolen, but I don't know if they can hand out the paperwork. If they don't or don't have them (I think they only keep them 10 years), you usually need to go to the TÜV, where an Engineer can evaluate it, either confirm the old paperwork if it is still in the KBA data base or use the standard registration for this type to fill out new papers. Then you have to take these to the kba to make them legal papers (at least if you wanna register it here). As the THW is a federal service, like the German army, it is possible it was never even publicly registered in the same way a car or normal truck would be. So you could be the first one to actually do it. And you technically did the right thing/used the proper method by shutting it off with the hand throttle. Probably the more correct method, but at least in the fire fighting scene nobody does it that way because you could forget to reset the hand throttle and somebody else might not be able to start it because he doesn't know. The button you called a stop button is you exhaust brake. It is just not regulated so it let's you turn of the engine. It also seemed to carry fire fighting equipment, even tough it was a THW truck. There were some labels for hoses and branches/hose nozzles. So the big space in the back was probably occupied by portable pump powered by a beetle flat four. I only personally came in contact with its successor, the 120-23 AW when doing my fire fighting fundamental course. It was a pump truck 2500l tank and a PTO driven pump in the back with basically the same cab, but as a 9 seater. So it had a second bench in the back behind the drivers seat, facing backwards. And if i remember correctly they were wooden too or at least really basic and hard. Even tough this was a truck from 1990 it was so much more crude and basic compared to the 80's Mercedes NG 1222 in our department. And your truck sounds nice, but the Deutz 6cyl can't compare to the Mercedes V6 engines, like the Om421 in the 1222. They just have this unmatched rumble due to their layout. It's Incredible. Which incidentally just recently has had a similar issue to your Iveco where the lockers wouldn't work because the actuation was seized. Sadly the local government decided to not spend any money on things not totally necessary so they just told the workshop to deactivate the switches. Which funny story they did by just cutting the air supply to the secondary consumer circuit of the four way protection valve. What they failed to consider, however, is that the the pto driven pump uses air from this circuit to clutch in and select the pto gear when you turn it on in the back. You couldn't even use the manual PTO switch because its also air powered. And sadly that's a trend with the workshop we use. It really hurts to see how this thing gets bodged up in the last few years of its service that started in '88. And luckily we noticed when practicing and not during an actual emergency. The only things to fail up until now where plastic air hoses used by the company that build by the company adding the fire fighting equipment, the mercedes hoses were always fine. And recently the clutch slave cylinder died and the lockers didn't work. Pretty good record, although it has only done 23.000km. I always thought I'd buy it if it goes out service, but looks like they want to get rid of it far quicker than I expected. So I probably won't have the money and funds to do so. Sadly.
Nope, all the THW vehicles do have normal registration papers like civilian ones, the only specialty is we have number plates mentioning „THW and a number“, and no regional number oh, and we don‘t have any insurance papers, there is no insurance company, but the federation itself which is liable in case I am driving a kind of grandson of this truck, a Mercedes Benz AXOR 1829 4x4 in our THW unit, after 10 years it has 16.500km
Well, i see a few things have already been awnsered by some of the others, here :) But i have to be honest. because of all the air-actuators on the transfer case, are not really working, i'm still not entirely sure if it is permanent 4x4 or not? but i don't think it is? And also, i looks like it only has a diff. lock in the rear. but again, none of it is working right now, so i could be wrong. Currenly i'm just going off what little data i have been able to find, on these. And thanks for that explantion. it makes sense that the exhaust brake is just choking it off. :) I can see what you mean about not re-setting the hand throttle. i already did that a couple of times, myself. Haha :) And yeah, i have also seen a lot of bodge-jobs done on fleet vehicles, simply to cut costs. it's a bit sad, honestly :/
@@KJOff-Road From what I could gather the posts in the "allrad-lkw-gemeinschaft" forum those trucks should only come with permanent 4wd with center diff. Additionally, that they came standard with a locker for said center diff. The one for the rear diff was optional. Which i guess is okay, because the center one should be more important. Doesn't help if your rear axle is locked, but one of the front tires has no grip and so only this one tire on the front axle turns. The exhaust brakes make the experience even better with their relatively untamed sound. Especially if you sit in the back and can also hear the air escaping the actuators etc. Its really sad with these things. That truck is basically pristine. Okay, it has some troubles with age, but they only come out because they don't care for preventative maintenance (if an air hose leaks they just cut out the leaking centimeter and just replace it with a hose connector. The whole truck is litered with them. Why don't just replace the whole pvc line?). Their plan is to replace it with a truck only ten years younger. However, our truck has these problems since around 3-4 years. So the "new" truck will probably be the same in a few years.
This is sweet ! What a unit ! There something about those old trucks. I have my licence for a 7T5 pls help me justify myself the cost and place to store it ahah
The THW still exists, it is a civilian volunteer civil defence unit. They are well equipped and well trained and supplement the regular civil emergency services. They have every sort of vehicle from fire appliances, command and control units, heavy duty road cranes, demountable pumps and even canteen vans.
I operated one of these until 3 years ago and did some repairs and rebuilds and stuff. So feel free to ask.
If you are going about 60km/h in 6th gear full throttle, it may be you are in low gear. Changing gears is somewhat tricky sometimes, it may stick in low gear even if the lever is on the left. What you need to do is pull the lever even more to the left, you should hear the air cylinder doing something. If it's sticking, drive the thing, go full throttle, pull the lever to the left and hold it, lift the trottle and back to full throttle. It should shift, if not do it again. Or try to get in in low gear, to make sure where you are.
The knob in front of that lever is the middle diff lock. The rear diff lock is the knob right side near the steering column.
It would be interesting where it has been in service.
Thanks a lot! thats very helpfull. and pretty much confirms how i figured the levers for the transfer-case, work :)
But it doesn't feel stuck in low range (if so, those are some extemely high, low range gears.)
i was able to get it up to speeds of 80-90 km/h. But it just took a really long time.
And on gear changes, when i hit the max speed in one gear, and then canged to the next, it barely had enough power to pull in that gear.
So it really felt like i just couldn't give the engine enough throttle.
But i still haven't looked into the whole ting, any further :)
Oh, and from the little documentation i have, i seems this served at a depot, in Suderlügum. and was last registered there, in 2016.
@@KJOff-Road/videos 90km/h means it's in high gear, for sure. It's high speed, maybe it will make 92 or 93. So fuel issue it is.
There was no THW in Süderlügum, but in Niebüll. Maybe from somewhere else and second life in Süderlügüm. I couldn't find anything.
You had some beautiful countryside to enjoy looking at while you were on your way home!
That would be such a good starting point for a camper build. Off-road capability and a sturdy functional box. There are many of these still around, see if you can sell the box to a fellow Magirus owner at least.
I have seen a lot og these, turned into camper rig's :)
Sick of hearing about Campers
@@KJOff-Road When you have the box off just place it in a barn and use it as a tool box. Crib up to the chassis height, and you have a nice new secure tool storage.
The problem with the engine rpm is likely to be the governor on the injector pump. If the seaĺ goes bad on the rear of the pump it causes a hydraulic problem that stops the governer from opening up.
i drove that type of Truck at THW many years ago 🙂
the trottle problem looks like a swamped diesel filter or the diesel HP pump (nned some maintenance)
BTW: the "shut off button" is meant as trottle-brake
Suggestion
Remove the shelf's
Keep the side folding platform and modified it so the "blue panel" could fold down (some named it 3way)
IMO it will make the "flat bed" more practical
Also that workinglamp somewhat feels soo coolll
That stop button in front of the seat, is the exhaust brake. But it also works as a stop button.
Mercedes used the exact same mechanism, until the late 80:s.
I drove a 10 cylinder Mercedes 1932 tanker truck for many years. Same setup, and the VDO gauges and warning lights were very similar. Even the steering wheel.
Ah, that would make sense :)
Thanks!
My 2 cents: careful how you build the roof rack. The noise it makes at highway speed can bring about a lot of regret. But all in all great find.
Put the box on a utility trailer for towing dirt bikes, tools and sleeping quarters, what have you, for off road adventures .
German guy here. If you can't get it sorted in your place - maybe I can help.
I shortly looked into it: With a buying contract (has to have the VIN in it) German KBA (Kraftfahrt-Bundesamt) should be able to provide the neccessary documents for a small fee.
Ich habe auch schon geschrieben, dass ich mich im Zweifelsfall mal mit meiner Zulassungsstelle diesbezüglich unterhalte.
Die Daten müssen ja da sein. Wäre traurig, wenn der Lkw nicht wieder auf die Straße kommt.
Would be great to have German help if he ends up needing to contact a German bureaucratic system 👍
Danke
Thanks a lot guys. it's good to know :)
I may get a hold of you, if needed :)
@@KJOff-Road Hi, I live in Sweden and had a similiar issue with an former German Ikarus buss. You need to get in touch with the local office too the city where it was registered.
There is no central office that has registration documentation in germany it all handled locally. If you have the german numberplate number that helps point you at wich office you need to contact. otherwise i would try taking contact with the THW becouse they probably have documentation on it.
@@KJOff-Road
With the THW license plates there are some things to know.
Because there are a special organisation, the KBA (Kraftfahrt Bundesamt) can't help you.
The vehicles are registered via the THW registration office at the Procurement Office of the Federal Ministry of the Interior.
I'm from Germany as well, please get in touch to me, If needed.
BR, Martin
Love the THW colours. They do have the coolest surplus sometimes.
Not a camping person, but the tray looks like it has heaps of possibilities and would be a great camper.
Remember seeing a few Deutz on the roads down under many, many years ago.
The yankee stuff put paid to serious numbers on the road.
See an odd one here and there. Have fun, stay safe and win the paper war.
I think that it is a really cool looking truck! 👍
OK, those sides of the bed are very cool!! It would make an awesome overlander...
@KJ Off-Road Hi KJ, German guy here who spend quite some time of his early life on THW and those rigs.
As already said there is nowadays a centralized license plate „THW- on the actual THW trucks. But they changed the system quite some time ago for all THW , Police , Katastrophic Services and similar agencies Trucks and cars. Even sometimes Fire Trucks. With different letters of course: e.g. the letters from the normal car plates for the capital of the german sub-country (Bundesland) like for example in Hesse the capital is Wiesbaden meaning all police cars in Hesse have „WI- plates. Makes shifting vehicles from one stationary to a different one a piece of cake.
That explained here comes the trick for you:
BEFORE that centralized practice those Trucks had real local Number plates like any other vehicle.
This means your truck probably had TWO number plates in his life meaning two sets of paperwork existed.
What you have to do is search the complete vehicle for remaining hints of those number plates, because with having multiple trucks if the same loaded goods and gear we have put frequently the number plate data (or a shortage of that) on the gear and multiple places in that truck. Basically everything removable that could be misplaced after cleaning offsite of these trucks needed to be identified to put it right back.
Also: inspect carefully the driver and passenger door. There must have been a time when „THW Ortsverband must have been signed in big letters on that doors.
This „Ortsverband …“ means something like Stationary.
So, with information of the old first number plate and the city name you look up the actual contacts of the THW of that city and ask them for the favor of a copy of that old paperwork. I know they keep goid records, especially the little ones like the one i was in.
If you only get the last THW-123456 Number plate you ask in the THW facebook group for a contact of the city name. You want to find the job role „Schirrmeister“ of that years after the manufacturing date of that truck to hit the jackpot of person knowing EVERYTYhYiYnYg of that truck because it was his duty.
And add a year when asking because sometimes they had the new trucks up to a year in stock coming from the manufacturer until all x-dozens of them where produced and then they rolled them out in the new version all at once to the different Ortsverband to make no-one jealous that the other ones already got the new truck.
THW people are nuts about their special vehicles and proudly show them off knowing every tiny detail if it - like fire fighters who are the same kind.
So as soon as you can name the plates and Ortsverband for specific identification it will be possible to find a person giving more details.
Good Luck!
Peter
Personally, I'd keep the side platforms, as it will make tying down whatever load you have on it a *lot* easier. I'd love to have something like this to build into a camper, actually, but I very much doubt I'll find one here in the US. Great find, and I wish you the best of luck getting it registered.
Put the box on the back of an old mercedes chassis - perfect for loads of craftsmen.
Double your money?
I love that the double cab is just two singles welded back-to-back
You'll need to get a type-approval document from the manufacturer - if that is possible, then you might be going somewhere!
Lovely project.
Lovely old Maggie Deutz. They were a very popular 4 axle tipper truck in the UK.
Yep I used to drive on . Great bit of kit..
Appears to have a governor to limit the throttle. Common in the US for fleet vehicles to keep workers from over revving and/or speeding
It could certainly be somthing like that.
My thnking was just that it we be really odd to put somthing like that, on an Emergency vehicle.
Sir that's a super nice work truck. Greeting from Murika.
@25:50 It's a diesel it probably has a govener limiting it, it really sounds like 17-1800 rpm to me, that wouldn't be out of the normal. I'd think 2500 would be too fast for that engine to spin, most older diesel engines are booking it at 2 grand
Hi Kasper in my experience you can't go past a sleeping berth, it's just so nice to be able to stop driving late at night and climb into bed. I'm looking forward to seeing what you do with this gem.
O yes. I know the sound off those air cooled Deutz engines so well. As a much younger bloke I served in the South African defense force. " yes South Africa did have a proper defense force back in those days. " and they're vehicle of choice was the Magirus Deuts. And yes, I was a driver. Fantasticly well built old trucks.
Known as SAMIL and SAMAG. South African license built magirus trucks.
South Africa only imported a small amount of actual magirus Deutz trucks. Around 2500 units if I recall correctly.
How ever produced around 16 000 SAMAG, SAMILs locally.
@@spotty4710 The SAMAG and SAMIL all used ADE engines though, the Deutz engines were only used in those branded Magirus, and also in aircraft tractors and such, along with use in the fire engines on all bases. The tractors used the Deutz engines, a Borg Warner automatic truck gearbox, and a modified Mercedes differential, along with a prop shaft that was basically 2 universal joints welded together, as the tractor was that small. But with it all being made from bent steel plate, thinnest being 6mm steel as covers, and then going to the chassis, made from 25mm steel plate welded to make the U channels and such, so that you had a 16 ton aircraft tractor, locked forever into first gear with a pin. Those were wicked fast on take off, though when they were involved in accidents, invariably the damage was to what they hit, and possibly a new coat of yellow paint on the tractor. I did rebuild one that caught on fire, memorable in that they used every fire extinguisher in the area on it before the brigade arrived. not worried about the tractor, but because of what it was towing when the wiring loom caught fire.
@@SeanBZA the Mk.1 models used deutz. Noted by the smaller grill style than found on the Mk. 2 and 3 models.
Nice ex-German „THW“ truck, Surely low kiliometers and very well maintained.
Just quite old, but good for people who like to fix a few issues.
but in relative good condition.
The little button on the floor next to the little lever is high and low low,it would appear you drove all the way home in low range.😂😂😂
It is a nice color Olaf, now i want one of those that box simply gave me so many ideas it would be awsome to convert into a explorer vhecicle the box allows for that making the kitchen and stuff acesseable from the outside and in the middle enough for a bed and bathroom simple awesome, plus lots of rom on the cabin.
To be honest, i wasn't so sure about the color, at first. But, i think it might be growing on me.
@@KJOff-Road Trust me, im a professional backseat youtuber 😂. it is time for you finally have some color in your fleet i know that deep matte blue is a bit to take in but give it some time for your eyes to adjust to it and you will find it not so bad. Also i dont know if you read my other comment about a rev limiter or the mechanism being stucked on low gear and the leaver being disconected somehow. BTW hows the shed renovation going? :)
german THW (federal agency for technical relief = blue) or fire trucks are always a good sign, low kilometers and still regularly checked and maintained
You scored a nice unit!! Good luck on getting registered
what a beautiful and clean country...and what a cool vehicle with so many possibilities...GL on chasing the paperwork..let us know what ideas you plan asap..
Magirus Deutz what a “cool device” I’m looking forward to the things you come up with.
Greetings from the country of origin.
Greetings Ralf👍👍👍
Interesting that you were allowed to drive it home. I live in Croatia and have an LDV Convoy van I used to move my stuff from UK in 2011. I've been doing some welding to get it back in roadworthy condition but again I'm not sure if I will be allowed to register it on Croatia plates.
Probably the best truck engines ever deutz tough as nails
Had this brand of truck when I was H.G.V.1 driving back in the 80's you could always rely on this no matter what, good old double bunk plenty of room when away for 6 weeks on jobs in its day a good truck to have.
I did a little research, and that truck has the Duetz F6L413 engine, which is a 4 stroke 9.6 L. V-6. It appears to be turning plenty fast RPM-wise (max is 2300 at WOT), but someone else mentioned the little lever between the seats as being for either a 2 speed axle, or the splitter for a secondary gearset in the transmission. Most likely, you were stuck in low range through the whole trip! If it's anything like the control valve for the PTO, it's probably worth looking into. I love the design of the body on that thing. It would be perfect for a tool truck at a racetrack, or for on site heavy equipment service!😉👍👍
I was in the South African Defense Force in mid to late 70's and drove a 10 ton long nose Magirus there. Cannot remember the vehicle Description numbers but it was one of the most reliable vehicles I've ever driven.
Just love the older vehicles...they just seemed better back then. Less electrical problems....
The truck is so old with so few kilometers on the clock... it hasn't even had the "major inspection" yet, the problem with the "speed" could be that the injection pump needs an oil change because old oil becomes "sticky" over time. The problem (which someone else posted) with the leaky seal on the pump comes from "many kilometers driven", but with less than 50k on the clock it is more likely "swamped oil" so that the pump cannot turn on fully. (I speak from experience, because many mechanics don't want to do this oil change because it is a huge mess)
Way that you used to "unstick the clutch" is actually smart! I used it on my man beacuse it had same problem and it works!
That truck is freaking cool!
100% agree . Strip out the rear body and turn it into living space .
Aluminium sheet where the side roller doors are .
Insulate with celotex sheet materials . Solar on the roof .
Honest it would make a fantastic camping vehicle .
Much nicer than sleeping in the back of the cab .
Nice truck .
We had a lot of these in Norway, but I don't think I've seen a double cab before. Very cool!
Great little truck. Pity the storage setup on it doesn't suit your needs, it's clearly well built and very functional. It needs to find another truck that needs it.
First time viewer. Haven't checked your other videos yet, but think that box would make a fantastic mobile service box for working on cars/trucks. Set on a trailer, it would leave the tow vehicle free to run for parts, supplies, or lunch !
Just like those old farmers in the US who salvage the bed off a "dead" pickup, build a trailer base and put the old pickup bed on top of it.
I was thinking that, ideal for a mobile welder or blacksmith.
DEFINITELY KEEP THE DROP DOWN SIDES !!!
you will kick yourself if you get rid of it !!
As to lack of RPM ? .. could it have a rev limiter ??
Ether Mechanical ore electrical ?
I used to drive a Maggy Deutz 8 wheel tipper. Great bit of kit not the most powerful but that Air-cooled engine was so reliable. It never gave us any problems. Not the quietest engine and it had its own peculiar sound. But us Drivers loved them..
Fantastic explanations, it’s amazing all the good work you do repairing and explaining. Many thanks for your dedication.
Hi, and I like your new truck. Here In the Uk, older trucks like yours are converted into Stock Car transporters with the crew cab ideal for family and mechanics to all ride along to race meetings. Anyway, good luck With your registration paperwork.
Oh it has the the air cooled v6 diesel, of course! I was slow to put two and two together. Awesome! It sounds like a normal diesel?!
Starting it in 5th to break the clutch loose is going into my Farm-Fix memory bank. Subscribed. Also I have a Deutz BF6L913 I am going to put into my 1976 Ford F250 (I'm American) soon here.
Putting an old Air-cooled Deutz in and ol' f250 is a wild idea!
But i'm all for it!
Nice!
A former „Bundesanstalt für Technisches Hilfswerk“
Magirus
You mean THW ?
@@WindgonnerTHW is the shorted name
Nice catch! It really is a shame to remove this cool bed, maybe make it a camper unit and just hitch the trailer behind for hauling 😉
Regarding the paperwork, I would start with the German TUV, with the 1 part of the German document you might be able to get the other part? Good luck and keep us posted! 👌🏻
Very cool truck Kasper - looks like you have a few wee jobs to keep you busy!
A beautiful air-cooled V6 engine. Deutz F6L714, built for eternity.
What a very cool truck. Subscribed now to see what you make of it. A great base for a very interesting vehicle
Awesome video. Thanks for explaining your thoughts.looking forward to next installation..Jason. Boston,UK.
awesome and outstanding.thanks for sharing and taking us along
Man, thats in really nice shape. Hard to believe it qualifies as a classic already! Sounds good too!
Only 46k Kms?!?! That is new!
In Denmark a classic vehicle must be minimum 35 years old
I really like that truck. I think it is going to work out well. I look forward to seeing more of it.
Congratulations on the acquisition of the ex-THW Magirus. Unfortunately, I didn't watch the video earlier.
Here is my tip: There is a website (in German) on which thousands of historic construction machines are presented and discussed, including many ex-THW vehicles. You may be able to get help there. The latter will perhaps come quicker if you register there and introduce the vehicle. As YT generally don't like links in comments, I will send you the link by email to the address you provided in this thread.
Good luck
Thanks a lot. I got your mail 👍
This might be very helpful :)
@@KJOff-Road The Magirus Deutz 170D11 is a widespread model that is also used by many fire brigades in addition to the THW. Both areas are known for the fact that vehicles are kept in them for a long time, especially as both fire brigades and the THW have plenty of opportunity to maintain their equipment when not in use. One more thing about the THW: The Federal Agency for Technical Relief (THW) is the German civil defence and disaster control organisation of the Federal Government with volunteer helpers and full-time employees in the portfolio of the Federal Ministry of the Interior and for Home Affairs. The higher federal authority has its headquarters in Bonn-Lengsdorf. The THW was founded in 1950 and has been a federal agency under public law with its own administrative substructure since 1953. The Federal Agency for Technical Relief is therefore a higher federal authority.
The THW has local branches in almost every municipality. The equipment with vehicles and other devices is quite comprehensive. They are not a chip shop.
The Magirus model under discussion is already quite old. Since ex THW vehicles are widely known for their good condition, quite a few have found their ways to small fire brigades or into private hands. Accordingly, the concerning knowledge should be widely dispersed. The spare parts situation should not be particularly tight either. You just have to find both. Unfortunately (for you) the whole area mainly takes place in German language. In special cases, however, I'd like to help with the research. In such cases, please send me an e-mail to the address you know.
I wish you continued success.
All the best
Uncle used to run a fleet of these things as dump trucks not this particular model bur the same engine. They where used as snow plows over here in the Highlands of Scotland 6x6 you couldn't kill them😊
Another amazing video! I'm pretty good with cars but your casual knowledge, especially of diesel workings, is fully engaging!
My new favorite youtube channel 🙂 Always interesting episodes 👍
I'd like to see a video of what tools you bring, how you transport tools and anything else you can add. Cool truck
I could be wrong but usually that button at your foot you pressed to stop the engine is actually called a decelerator, its used to retard the engine exhaust when travelling down long hills, it helps slow your vehicle down without overheating the brakes especially when carrying a heavy load..!
Hope this helps
I’m driving/working with iveco 160(that one with you wanted)amazing truck
That thing is awesome! Good luck with the paperwork!
Great interaction guys
Such a cool truck, and such a great way to start my weekend. Thanks for a great video KJ
That thing is really cool. And you have some great bike lanes where you live!
Always wanted one of these or a bullnose mercedes 1113 for a camper build. Love it. Looking forward to more videos. Good luck sorting out the paperwork.
You could keep the box and put it on a slight foundation ... to use as a "tool shed for outside" (garden hoses and so on) ... and as a "sunroof sitting lounge".
That way you still have it in case you want to "go on a safari".
That Box would make an ideal base for the construction of a camper, and with those step sides it opens up possibilities for slide outs or canvas extenders to increase the usable space, along with the under body boxes for storage etc, even if it is not used on the current chassis
Maggie D's always seem to sing nicely, no matter which engine they have in them, they ALL have a gorgeous exhaust note.
That's a cool truck. Hope you get the papers sorted
Awesome score there KJ. Shame about the paperwork. Take care & stay safe.
You can’t get rid of that box man. You can’t. It’s literally every man’s dream.
Congrats on the new vehicle. Hope you’ll succeed in getting it registered 🙂
Nice truck! That wouldbe a great truck for my job! Hope you get the papers sorted. Good luck!
I hope you can do the paper work to see what we like, the mechanic work. Good luck!
Dude can you show me the NATO jumper connector at some stage, if you think of it please, interested. I spent near 200 euros on some 350 amp andersons for my winch and , well thats too much!
Lovely truck. I dont know jack about those air cooled engines, never seen one, very interested to know more, find it hard to comprehend how it would keep cool under load. That IFA was a beaut. Great content.
Thanks!
And yeah, that is definetly too much!
The round Nato style connector are usually more expensive than the "Anderson" connectors. and even then, a set of nato connectors should only be about 100-150 euro.
THW is the ones we look up to in civil defence. They are GOOD!!!
Muito bom, havia de ter comprado o camião velhinho também... Merecia a salvação. Abraço 😊
There's normally a return spring on the injection pump lever.
Kan du inte bygga en släpkärra av flaket?
Cool truck, very useful. That bed has got to worth something to someone, it should help to offset the cost of the truck if can sell it to someone who wants to build a service truck. Hope you get the paperwork sorted, I am sure you will have some subscribers who will help you out😀👋🇬🇧
Hej KJ. Gammelt jern kan man bedre stole på end det moderne med elektronik. Jeg har betalt depositum for en Volvo Viking 4X4 Ex mili fra 1863. At hente den bliver en tur på ca 800 Km. Sjov at se din beretning. Tak
Looking forward to this project.
Enjoy your channel and content, Thank you.
Kaspar, I thought getting imported vehicles registered in Australia was hard, we have it easy, no need to find history etc for it, so long as the numbers match the export/import documents no sweat. a tray keepin the drp down side platforms and a ramp would to me be ideal and use the box as tool storage and centre aisle of the box as somewhere to store long lengths of steel, and when you showed the middle on left side of the box instant location for a decent compressor. my thoughts but hey I'm Aussie. Pete
Hah, yeah. it really can be quite a headache. with the system we have, the paper-work is more important than the vehicle itself.
@@KJOff-Road I recognize the blue/white paint on the truck. This was from THW of Germany, a civil defense service team. Germany also has a dedicated water rescue team known as the DLRG.
It shouldn't be too difficult to get remade German THW paperwork from the THW itself or the road authority where she was stationed back in her active THW-time I reckon. Biggest issue might become that everything needs to be in German, officially translated and/or officially seen and approved by a notary. You might even get a full history of maintenance and repairs, should they have taken that on micro-film before selling her. Crazy archives in most of those places in Germany.
i suggest a sleeping cabin where teh backseats were and a storage unit in teh center of teh vehicle and then ANOTHER sleeping compartment with a fold OUT tent system at teh end like a caravan camper . the center storage unti should have folding out cooking stations for small meals so u can BBQ in teh wild ^^
Great purchase and video. Good luck on getting it registered! 👍
Looks like an old THW GKW nice
GKW I. It has a winch. Used to drive the thing a for a while in the early 2020s. The only disadvantage is the ventilation - you wont see anything if you have people with wet clothes in there with you.
It sounds like the governor is sticking at high RPMs. A little Marvels Mystery oil in the oil for about 30 minutes and then an oil change might solve the problem.
The box might be a good idea to keep and modify. It would hold a vehicle and keep the vehicle from the weather.
Is there really an issue with the engine? When you liftes the cabin I could not see a turbocharger. If that is true the engine would probably not go over 2000 RPM. The sound ofthe engine at around 26:00 seems to support this. Before you undertake some big repiairs you may want to check the datasheet.
The sound remeinds me strongly of our old Mercedes 407 from the Red Cross. This engine didn't have a turbolcharger either and the range of RPMs was very low too.
Olaf the truck may have a rev limiter, i know now adays companys put a speed limiter of 90kmh on trucks so maybe it was some kind of rev limiter since it was a rescue truck maybe it could be used as a auto tanker and later converted to a utility truck i dont know just look out for a rev limiter or maybe its just stuck in low gears and the leaver is not connected or just falling apart. but good color choice
Nice truck.
Which year is it? You didn't even tell us. The 4wd is permanent with a center diff, right and only the rear locker?
I As for the registration I am not sure if the KBA can really help you with this. They can probably confirm that it is not stolen, but I don't know if they can hand out the paperwork. If they don't or don't have them (I think they only keep them 10 years), you usually need to go to the TÜV, where an Engineer can evaluate it, either confirm the old paperwork if it is still in the KBA data base or use the standard registration for this type to fill out new papers. Then you have to take these to the kba to make them legal papers (at least if you wanna register it here).
As the THW is a federal service, like the German army, it is possible it was never even publicly registered in the same way a car or normal truck would be. So you could be the first one to actually do it.
And you technically did the right thing/used the proper method by shutting it off with the hand throttle. Probably the more correct method, but at least in the fire fighting scene nobody does it that way because you could forget to reset the hand throttle and somebody else might not be able to start it because he doesn't know.
The button you called a stop button is you exhaust brake. It is just not regulated so it let's you turn of the engine.
It also seemed to carry fire fighting equipment, even tough it was a THW truck. There were some labels for hoses and branches/hose nozzles. So the big space in the back was probably occupied by portable pump powered by a beetle flat four.
I only personally came in contact with its successor, the 120-23 AW when doing my fire fighting fundamental course. It was a pump truck 2500l tank and a PTO driven pump in the back with basically the same cab, but as a 9 seater. So it had a second bench in the back behind the drivers seat, facing backwards. And if i remember correctly they were wooden too or at least really basic and hard. Even tough this was a truck from 1990 it was so much more crude and basic compared to the 80's Mercedes NG 1222 in our department. And your truck sounds nice, but the Deutz 6cyl can't compare to the Mercedes V6 engines, like the Om421 in the 1222. They just have this unmatched rumble due to their layout. It's Incredible.
Which incidentally just recently has had a similar issue to your Iveco where the lockers wouldn't work because the actuation was seized. Sadly the local government decided to not spend any money on things not totally necessary so they just told the workshop to deactivate the switches. Which funny story they did by just cutting the air supply to the secondary consumer circuit of the four way protection valve. What they failed to consider, however, is that the the pto driven pump uses air from this circuit to clutch in and select the pto gear when you turn it on in the back. You couldn't even use the manual PTO switch because its also air powered. And sadly that's a trend with the workshop we use. It really hurts to see how this thing gets bodged up in the last few years of its service that started in '88. And luckily we noticed when practicing and not during an actual emergency.
The only things to fail up until now where plastic air hoses used by the company that build by the company adding the fire fighting equipment, the mercedes hoses were always fine. And recently the clutch slave cylinder died and the lockers didn't work. Pretty good record, although it has only done 23.000km.
I always thought I'd buy it if it goes out service, but looks like they want to get rid of it far quicker than I expected. So I probably won't have the money and funds to do so. Sadly.
At 16:13 he says it is from 1985
Nope, all the THW vehicles do have normal registration papers like civilian ones,
the only specialty is we have number plates mentioning „THW and a number“, and no regional number
oh, and we don‘t have any insurance papers, there is no insurance company, but the federation itself which is liable in case
I am driving a kind of grandson of this truck, a Mercedes Benz AXOR 1829 4x4 in our THW unit, after 10 years it has 16.500km
Well, i see a few things have already been awnsered by some of the others, here :)
But i have to be honest. because of all the air-actuators on the transfer case, are not really working, i'm still not entirely sure if it is permanent 4x4 or not? but i don't think it is? And also, i looks like it only has a diff. lock in the rear. but again, none of it is working right now, so i could be wrong.
Currenly i'm just going off what little data i have been able to find, on these.
And thanks for that explantion. it makes sense that the exhaust brake is just choking it off. :)
I can see what you mean about not re-setting the hand throttle. i already did that a couple of times, myself. Haha :)
And yeah, i have also seen a lot of bodge-jobs done on fleet vehicles, simply to cut costs. it's a bit sad, honestly :/
@@KJOff-Road From what I could gather the posts in the "allrad-lkw-gemeinschaft" forum those trucks should only come with permanent 4wd with center diff. Additionally, that they came standard with a locker for said center diff. The one for the rear diff was optional. Which i guess is okay, because the center one should be more important. Doesn't help if your rear axle is locked, but one of the front tires has no grip and so only this one tire on the front axle turns.
The exhaust brakes make the experience even better with their relatively untamed sound. Especially if you sit in the back and can also hear the air escaping the actuators etc.
Its really sad with these things. That truck is basically pristine. Okay, it has some troubles with age, but they only come out because they don't care for preventative maintenance (if an air hose leaks they just cut out the leaking centimeter and just replace it with a hose connector. The whole truck is litered with them. Why don't just replace the whole pvc line?).
Their plan is to replace it with a truck only ten years younger. However, our truck has these problems since around 3-4 years. So the "new" truck will probably be the same in a few years.
This is sweet ! What a unit ! There something about those old trucks. I have my licence for a 7T5 pls help me justify myself the cost and place to store it ahah
sweet truck dude, perfect overland vehicle?
Is it an Old THW-Truck?
That crew-cab, Would make a great sleeper cab!
She might be old, Still a very good truck!
Deutz Awesome gear !