Відео

Can you fit 50 gallon water heaters in here?

I see a lot of comment on these pumps that it doesn't make the expected flow rate improvement as per the manufacturers graph. For example 2LPM will be increased to 7LPM (350% increase). In the case of a low pressure gravity fed system that has a mixer tap restricting flow rate (typical scenario), you can't measure the output flow rate of the tap as your point of reference for improvement. That is the restricted flow rate, the flow rate entering the tap will be higher prior to the tap restricting it. That higher flow rate is what the incoming flow rate the pump will be connected to. The higher the flow rate the less it will increase it e.g. 8LPM to 10LPM (25% increase). This video is a good example of that type of scenario where the improvement is quite disappointing. Whilst flow rate out of the tap might be in the region of a paltry 2LPM prior to the pump being fitted it would be incorrect to expect it to increase to 7LPM as per manufacturers graph. The flow rate to the tap could be 7LPM but is restricted down by the tap to 2LPM. Therefore the pump will see an input flow of 7LPM and only increase to 9.5LPM (35% increase), then the tap will restrict this back down 2.5-3LPM resulting in the quite pathetic increase seen in the video.

ua-cam.com/video/8kX8l8JMoJY/v-deo.html If that's the money shot, you're easily impressed.

Remember your tool box tour. You should get a bahco sponsorship

Shocking what was in there lol

That intro was good I subbed just for that great van mate

Would u buy a Bigger van .. Eg a high top transit or LDV , nissan , maxus .. (Ideal so i can stand up inside van lol 🤣

Hello professor, is there a way to find the right part number for a hansgrohe thermostatic cartride? I just moved into a new place, i need to replace it but there is no number on the cartridge. Thx

Best tranzit connect I've seen yo!

Very useful upload but very disappointed with results and they it seams are not cheap

Quick question pal is it only for hot water or can you use it for cold water as well I have the same problem but in the cold water? Many thanks Ahmed

I bought the 20l Dwayne orange bucket a month ago and have use it almost everyday since. Great for under a boiler or in any hard to reach areas under floorboards etc. It has been a great addition to my drain down kit.

Your vids are chaotic mate, can you keep it still for 5 seconds.

useful vid, Just fitted a new small bore mixer and now the flow is rubbish, so I'm going to buy one of these tomorrow. Thank you for the video

Thanks mate. Been looking to swap out the PRD on one of these and seeing how the plastic bottom half pops out has helped me get to the PRD hidden behind the Outlet valve.👍 👍

It maybe outside of spec' but I'm using a home boost to pump a fortic tank output. Fortic tank is in the loft, and homeboost under the bath to supply a bath mixer. Bathroom has cold main feeds so normally severely imbalanced supplies. Works ok even for a shower. Looking at the manual suggests can feed an outside tap so I may have a go seeing if I can get this running off a 12v solar panel / battery setup. These pumps are bit pricey now though.

Its called a street elbow. m n f, what the. . .

Lived the video you make it look so easy👍m

Nice video. Just curious is the hot water cylinder therefore earthed with all the copper pipes? So don’t need earth wires?

Haha that leak at the end... Im 3 weeks into my entry to domestic heating course and just learnt how to fit a unvented hot water cylinder... So its good to see even the pros make the odd mistake 😂

Mate..don’t get a bigger van - the amount of dinks and dents you’ve got on that little one you’d write off a bigger one 😂🤪 lovely set up you got pal! Love it 🤙

How long did you wait for the silicone to dry?

I haven't found out anything about where the hot and cold water connections go.

Must admit I start with top brackets

Kneelmat? Are you a pensioner 😂

Can you fit a water heater in the back of that?

Just got you to 1k ;) - Keep the vids coming dude.

I tell you best tool t use to take hans geohe cartridge out is your tap box spanner. The side you use for basin tap it fits perfectly. Can als use it on prv heads

Hi there,I would need your advice,I've just installed the pump in your video after your recommendation which is replacing a salamander ct 50. From the moment of plugging it in ,the pump won't shut off(I have primed it for a few minutes prior to switching it on).Must mention that the pump is working the bath taps and that's where it is located right under the bath taps -3"of outlet pipe after its flexi hoses.Did this ever happened to you before - not shutting down? Thanks in advance

😂😂😂

Only champions like unvented cylinders good job 👍

Nice vid, nice that you have an apprentice, good to show how it's done, and done well. Was amusing where he was lubricating the male end of that connector instead of the female, you had to jump in there quick before it went wrong!

Nope

What’s the internal diameter of the flexis on these. Are they the tiny 8mm ones that you sometimes see or the 10mm ones? Cheers matey.

Would love to know what you think about this light compared to the Unilite ….???? I’m looking in getting one

How often should the internal bubble need recharging? Have to do mine every 3 months.

DE BLAOUUUU!! 😂

£600 for complete set You for real !!

The big tub needs handles at least 😂

drill pump red nerrad bend it to shape and my yellow tub from artic hayes plus the blue tubs which come in handy when im on my own job done third of the price but if was free id rave about it as well great vid mate keep them coming some great some not so much

280 quid for that drain down,na I don’t think so

Hiya mate. I think the reason you sleeve the pipe is to stop the copper from corroding due to the lime and cement which breaks down the copper. Nice job

I think the nabis basket strainers are the best ones. Has a brass part for screwing in bolt. Mcalpine traps though all day long

Christ that 1st lagging cut was a bit close to your fingers! Haha

You said you'd show the prices on screen. Plus, no price per glove breakdown, which would have shown the relative real cost/value. All you really did was play with the gloves until each one broke.

Same still crap gettting fixings ect

Why do we do it at 20-21mb what is the reason? Thanks

My plumber has suggested this as an alternative to the expensive 2 bar pump fitted at the tank end. So I was keen to see how this improved the flow. Unfortunately your video somewhat skipped over the important part. I think you should have dwelled on the improvement - or lack of - and it would have been good to get the customer to give his impression. Also timings would have been VERY useful. Ie. It takes 45 seconds from the tap being turned on to getting hot water out of it WITHOUT the pump and WITH the pump it was only 20 seconds. That sort of thing.

Nice work! How much would you charge for that?

Liked the mash up