Відео

Did the lights ang gauged still come on strong ?

Thank you this help a lot

just ordered. thanks.

Did you experience any overheating when you had oil in the coolant?

I know this is an older video, but does the truck sit high in the rear?

Butler where?

What can I do if the plunger won’t budge even if I am pressing the button

Nice. This will help me out with my MJ projects.

I just received the exact flares and I only looked at the review stars and not the individual accounts. I have only started on the rears and the alignment is pretty bad. I’ve heard some people say the passenger side has better alignment than the drivers side. Question- does the rubber seal go on both edges, inner and outer? Thanks and great video👍

How are you going to make a video and not actually show wtf you do

How long was the mid pipe you cut?

Well I just took mine to the shop and after I told him what was wrong with it they told me there's no way and that's what's wrong with it but they told me I had to replace all my hoses because oil seeps into the rubber And they need to do a acid flush

Those injectors are a pain to remove. Especially the passenger side. You could just grab a hold of them with your fingers, must add to the equation is a set of angle picks to pull those injector plugs, especially if they never been removed before, some were melted in place due to weather conditions, and normal engine running.

Hope I find part 2 ?

Any differences for a straight drive ?

I was glad to see this cause I have a pioneer Metric ton with the Dana44 and trakLok. I don't see why we wouldn 't just hang the axle over the springs which would ( haven't measured it yet) lift it pretty close to the 4 1/2" amount. I don't like underslung. Comment?? Dandahermit.

You can spread those bracket tabs with a large bolt n nut inside to use as a spreader.

I hope your next video on the rear axle comes next cause I wanna see how you deal with this underslung axle cause looks to me like mounting the axle under the springs will lift this much. My axle is the Metric ton option Dana44.

What company's kit is this?? RC ??

The valve cover you cut 1in from the bafual then a hole on one or both now (why) .?

Thanks for the detailed list in the description. I'm doing this on my 2012 very soon, your video was useful. I like your little ladder setup, lifted Jeeps are great for getting to stuff underneath but not so good for crawling around the engine bay. I use one of those little metal folding chairs for mine.

what brand did you use?

Where did you get the patches from?

So was that the problem? I have oil in my coolant but no issues with the engine running.

Dàmn music ruined it for me.

Damn that sounds good. Mine comes in tomorrow. Can’t wait. I wonder if you started with the intake. Anyways thanks for the vid

Thanks bud! Super helpful 👌

So the speakers in the dash and sound bar are the same size? Just asking so I can put in an order for 4 of them total.

Why did u put on the old model. Should have upgraded to the '14 and above model with the new filter design.

How are these fenders holding up? Are you still happy with them? Thanks!

I changed mine out last night and I don't know who the engineer was behind this but they need a good swift kick in the a$$ .lol

bump stops just pop in?

Thanks for the video!!! Seems like a pain in the a$$ to install, but the results are great!

Installed this on my 2013 after I had a 2" spacer lift. The difference in ride over road bumps was great, stopped wandering. Great bang for the buck !

What speakers did you use from Amazon that were a direct replacement. Oh by the way that was a very nice video. Also gave me some things to look for in the buzzing sound of my sound bar. Thanks

Hi. Where did you buy your cable? I have an 86 & can not find the correct cable. Rock Auto has a 57" cable for it but when mine is out it measures 64 1/2". Thank you!

What JKS doesn't tell you: these brackets are a bolt-on for 07-14 JKU'S. For 2015-2018 JKU'S you're going to have to cut the passenger side upper mount to "clearance" these, at which point you're stuck with them for life. I returned these on account of this because I didn't want to be permanently attached to them. These are a $200 part which exists purely to try and avoid buying the correct $800 part, but they are NOT bolt-on for ALL JKU'S as JKS claims.

Nice!!! What back spacing do those wheels have?

NICE JOB👍LOVE THE WAY YOU PUT YOUR "SWEAT" INTO YOUR "PYPES"👊

don’t happen to know what bump stops you used do you?

I am currently going through this now. My fluid was a lot more thick and gunky. It overheated for the first time ever and when I popped the hood I could see there was oil in my radiator. I replaced the whole cooling system from the water pump to hoses, thermostat and radiator. I flushed twice so far with engine flush and it’s still getting hotter than it’s supposed to before I cut it off (because I don’t want to overheat it again) how many times do you think I need to flush it before the temperature levels out to normal?

Is the process the same for an 88 Comanche?

My Odyssey Extreme lasted like 1.5 years. 🤦🏼‍♂️

I was flabbergasted by this install

I was flabbergasted by this install

Eyeballing these. I'd hard finding someone to talk about barricade other then extreme terrain (that owns barricade). So unbiased reviews are needed

Great video, so i chenged mine out a couple of years ago because i had a leak like you said i thought it was my rear seal. I was checking my fluids yesterday and come to find out that theres oil in my coolant not sure if im dealing with a bad head gasket or its this thing how did it go for your jeep did that solve your problem?

Super helpful video! Thanks for uploading!

I can’t get a clear spec on the torque for the oil cooler housing. I broke one bolt and stripped the hole on the number 2 bolt hole. I have heard 106 inch lbs, and 35 inch lbs I set my wrench to 106 and broke and stripped bolts. The torque felt excessive for so small of a bolt but I was doing what I throughly was right. I got the broken bolt out easily but try to figure out about bolt hole 2 I lost.

How it’s holding up so far my friend thinking about getting this one., does it leaks inside