Відео

Thank you for the information you might find it surprising that the owner's manual doesn't even tell you how to use it it just mentions that it exists. Also at 100% power, the microwave can hardly cook a cheeseburger.. worst microwave don't buy

Thank you

Is there a way to lock in the power level to always be on 80,90 or 100%

You suck

Hello I would really appreciate it if you could help me with this problem I have. , I have a KitchenAid cooktop model KICU568SBL1. It comes with two identical positions on the left side, two positions in the center and two positions on the right side. This Cooktop comes with 3 main control boards, one control board for the two positions on the left side, a central control board for the central position (2 induction positions) and the other control board for the two positions on the right side. It gave me an error code F0 in the positions on the right side. When I checked carefully, that control board had problems and had to be repaired or replaced. I was fortunate enough to get the same control board for that position since it was not available. It was changed correctly. The error code F0 no longer appeared, but I am left with a problem that I do not know how to solve. The problem is that the two positions are reversed, when I turn on the one below on the right side, the one on the top turns on, when it gets too hot I get the H because the sensor is in the correct position and it cancels (flashing 2 and the letter c), this means that there is too much heat. Everything inside is correct (wiring), everything is in its position. I imagine that a reset needs to be done on the control display, does anyone know how I can solve this problem? Disconnecting it from the power is not enough. I would greatly appreciate it if someone could tell me what to do. Has this ever happened to you? . In short, what happened is that the selector changed position and I don't understand why since everything is connected correctly and has been rechecked a couple of times.

Owner's manual is not owner friendly. Wish they had included clear pictures and directions. UA-cam is good to make tutorials about your products.

The left side of the oven door came out how can i put it back in do i need to put it back like that or do i have to take the whole door off to set it back

Show me how to snooze my alarm clock (CASIO) Next time!

Thank you from Detroit 🇺🇲

Thank you worked 😊

This system is junk. Ours stank and now the washer appears to be jammed due to gunk in the pump motor. The built in grinder is not sufficient.

I was looking for something deeper

Stouffer's lasagna brought me here

I read complaints that the utensil basket is tooooo long. You can actually separate the 2 sides from the handle and use just one (or both). There are 2 white tabs that attach the sides to the handle.

This video is amazing! It is must I wanted. I bought Whirlpool washer three years ago and it run well. My wife accidently put more detergents yesterday. Washer did not ran and gave me F8E4 error code. I just watched the video and clean the tray. Now it works again. Thanks.

Why don't yall get the camera even further way from where you're working so people have no idea what youre doing!

Anyone know if this part replaces the one in the KitchenAid dishwasher W11361452A ? Also is the part number - OEM Whirlpool W10861000 Detergent Dispenser ?

I had a manual microwave before and I loved it. I looked for another one but didn't find many and finally settled on this one, but honestly, I don't like the electronics. Would MUCH PREFER a mechanical dial operation.

This video helped me pinpoint that my water hookup, wasn't fully tightened, and would drip occassional setting off the alarm. I could see the issue by removing the foot plate, and running a cycle, and in the front leff I could see water dripping from the brass 90 degree elbow, which I could easily tighten up with some pliers. I posted a related video here: ua-cam.com/users/shortstKH7Xddt9JU

OMG! This video saved the day! We thought it was going to be something major. Called My Best Buy Total and they said their coverage only gave us a 20% discount on repairs and it was going to be $99 call out fee + $200 diagnostic + parts. We did exactly what you said to do and it turned out to be a full drip tray. You saved us a small fortune! Thank you so very much!

is there some magical control lock function for the KDPM704KPS dishwasher with pocket door, and top control panel. I cannot believe KA would have made a dishwasher in the last 2 years without a control lock that cost $1489.00 msrp , Please tell me this is not the case. I keep hitting the a button when wiping down the counter. The dishwasher door is not opened. It seems like it pauses or stops. I need to be able to lock out the top controls. This is the model with the led runway lights inside for illuminating the cavity. Does Control Lock have to be activated maybe before the cycle. I have prodry button, and top 2 rack button. I understand both of these can depending on model can activate Control Lock with 3-4 second press.

Thank you

Excellent, thank you so much.

Is the power level same with temperature?

In the video the head lock on the right side of the machine is not engaged. I have been playing with the adjustment screw to get the lock to engage enough to secure the head. My machine is pretty new, used it only a couple of times. The head was jumping rather violently when I was working on a bread dough. So violently that the lock lever moved and disengaged the lock. This should not happen on a new machine! I discovered the adjustment screw on my own and was able to see how it worked but in doing so some paint chipped off the dough blade and is now in the dough. I grew up with a KitchenAid mixer and don't recall it ever being a problem. I am not so thrilled with my new machine after this experience.

Thanks it works for GE too.

Yay! Straight to the point east tutorial!! Thank you!!

But it says A1

Power level: PL 10 0:25 PL 5 0:31

My wire broke

Thank you so much 🙏🏻

Stupid video

Worked perfectly. Removed drip tray and emptied. Thank you:)

Thank you for your help 👍

This video is entirely worthless without showing the part number on the bag.

So I have to do this each time I cook something? Why can’t I set a default power level?

Rename the video "installation troubleshooting tips"

Can I make it more than 10?

These are all designed the make you buy the extended repair warranty.This video is a waste of time.

After you set it to 5 does it go back to 10 after its done or stay at 50%

Thank you!

This was an amazing video. I had no idea how the spring worked and spent a good solid 15 minutes trying to fin-angle with it. Imagine my surprise when the alignment holes appeared in my field of view when you mentioned them :)

What is the power level to cook pizza

Thank you for this video Im learn More about microwave, I watch video fron México 🇲🇽 👏🏻 👍🏻

Thank you the button was right in front of my face and I still didn't flipping see it !!!!

I have the KFP720081 and I can't take the bowl off😢

my spring got bent. where can i get a spring only

Thank you , it worked !

Where can I install the range

Worthless ass video