Відео

What you need to do with this type of videos that, show how much fork was moving while rusty and how much after cleaning.

I have a similar shimano freewheel and the hub is very stuck, where I can get that tweezer like tool and the socket to do the job? Thanks.

Dzięki.Pomocny film

Meu quadro é soul sl329 essa caixa de direção pega nele?

Who in the hell has a bench wheel laying around !!!

Cleaning FAKE! rust tutorial. Do you know what rust is ?!?

😮😮😮 this idea is absolutely fascinating. I am most definitely going to try it😊. To my knowledge, it's only available here in South Africa, but after completing the project, I'm going to cover it with ALCOLIN SILICONE TAPE to make sure that the inner tube doesn't move around. Thanks a lot for your information. This is going to be fantastic👍.

I prefer to buy new and use my time for more enjoyable activities. Those stems are really inexpensive.

is this a road bike freehub or mtb or the same ?

Lol

My fork doesn't have those two bolts at the bottom please help me

Zbyt lepki smar. Niepotrzebnie.

What's the red stuff that you use on the threads?

I did this but the shifter doesn’t work. Can’t change gear at all.

It works, got it on the first hit

Estou seguindo #brazil

good good good ❤❤❤

Thanks for the video. I needed to verify that I am turning counter clockwise to loosen that bolt. and it wont come off. I removed the freehub casing, bearings, etc but the main part is still in there where the pawls ride or attached too. I have it in Blaster penetrating oil and will give it a shot tomorrow again. I am using 11mm for this one. There is about maybe 1/16 movement left and right when I try to remove it. Any ideas? Maybe I just need to buy a new wheel and move on on this project. I dont know if I can get a pipe wrench and grab that main part and try to loosen that way. I believe the freehub is geared to match the hub to lock in place (for no slipage) and that bolt holds it in place to the hub - so I am thinking that will not work: the bolt has to come out if I got that right.

Was that 120 mm track wheelset made wider for 127mm dropout or made to order part.

Aluminum foil over steel wool.

Thank you for the video. Just a constructive criticism instead of annoying music. It would have been nice to hear someone describe what they're doing

thank you good job

"3de printer kay" 🙏

"dirty 😔"

The wox is important.

Caution: Some RevoShift shifters have small very recessed screws holding the plastic housing together so you can't pry it off with a flat head, as this video shows.

Według mnie nie powinno się mieszać smarów w tak bliskiej i otwartej odległości. Ja bym dał ten łożyskowy na te trybiki i z bani, bo akurat dzisiaj też rozbierałem wolnobieg i smar z dolnej i górnej części przeskoczył. Tzn. przy skręcaniu wolnobiegu nadmiar idzie bokiem nakrętką i przy okazji na te trybiki.

DO NOT USE A RAZOR BLADE THAT HAS BREAKABLE SECTIONS OR A RAZOR BLADE AT ALL ...I DID IT WITH A FINGERNAIL OR SMALL FLATBLADE

I just finished servicing my 40 plus year old Schwinn Montague. There is something special about saving an old bicycle and making perform like new again. Much better than throwing it away....

Zoom produces cheap steel garbage. There should be at least rubber covers on fork. I had to use so much force that fork bent, after a lot of beating and it freed up. Can I still bend back fork legs?

10 Sekunden, schwer angegeben 😂 !

Myslím že to bola zbytočná robota lebo v tých miestach kde si to obrusoval sa stenší vrstva kovu a tým pádom bude mať vidlica v tých miestach vôlu.

Thanks for the video!

Does somebody know, what size steel balls are used in the MF Z012 freehub? And How many on Top and Bottom (as asked in another commend already) Thanks PS: Thanks for the nice and very usefull video :)

Bicycle noob here. Just trying to take that crank model off ( and support too ). After taking the plastic caps off, I dont have a hex there, but a T40 torx hole inside of a 15mm nut. Tried to whallop it counter clockwise with a T40 and a small hammer, but it wont budge. Bike is new, so I dont want to brake anything. Any tips? Do I need a special tool for it?

Always put the shifter first. Then the brake lever.

perhaps use captions instead of talking with that heavy nats accent.

It seems the dust caps on top of the bolts were not put on. Am I wrong?

whats the white thing? il the red is grease but whats the white

On my bike, the gears shift down, but I can't shift up (on the rear wheel). Do you have any idea what could be wrong?

Great job !

After watching this video, the first method was actually more useful and worked, unironically. (if you're replacing the entire headset)

OMG Don't use Torx on hex bolts! ☹

Good Job. But , i like the red paint red

@1:42 I fled from the "music".....

I appreciate the tip, very helpful. Thank you.

CHAIN RINGS ARE NOT POLISHABLE?

Thanks bro :)

One of the best explanations - cheers

Comoda la vita