Відео

You and others I have seen are informative but no one shows the vehicle starting and running.

never had a issue with these been doing it for 38 years at a ford dealership, you didn't do it right

Loved your content. Liked your Chickmunk sound. Lol!

Thanks. What happened to the old knock sensor? Did you remove it or keep it?

Nice truck 🤠

Nicely done Ken.

This didn’t work for me. I’ve put the sensor in 3 different spots on the intake. The wire in my harness was red that was on the left. Had 2 wires on one end , red and white that I cut off but the business end going to sensor only had the one red wire on the left. Truck still has rough idle.

I'm gonna watch you so I know what to do on my floor pans.

Glad to see you back at it Ken! Pretty good progress.

Where you get the sensor ?

Looking awesome

Thanks so much man this is the best video out there. Finished the job in like 30 minutes with electrical tape. Your the man. And for anyone wondering i used a 1 inch bolt for the sensor

That was a lot of work. I enjoyed following along for the whole project.

Thank you for showing this video

Mahalo!

Thank you for this video I have a frontier I have to replace the sensor Can you purchase the connector separately from Amazon??

Call those pumps "clicker clacker" pumps

Check your trackbar

Great vid! Will be a big help for something I’ve been dreading on my 02 Overland

Bring engine to 3500 rpm’s and see what it does

Wish the volume was higher One leg is not putting out Properly the board

Great work. Do you have any info about changing the belt on a grasshopper 729T6 • Optional Hydraulic Lift Assembly?

I did this mid today on a 2000 pathfinder 3.3L. So far so good.

Thank you!!! You just saved me from tearing apart my whole brake system trying to figure out why my front brakes kept acting up.

Hai my name sak i have been working on the same engine missfire i even change distrubutor on still

Nice job Ken! And hello. 👋

Isn't the root suppose to point to sparkplug #1? I'm confused.

Feels like I’m watching a classic old time diy videos with this kind of quality of camera I like it ❤

Everything done just like video/ still po325/ can t figure it out....?? Catalytic converter shot?

I have the 99 3.3. Sometimes that code will set, most times right now I can go for miles, days, weeks. Its intermittent on mine. Should I try plugs wires cap and rotor button replacement first? Mine uses NO OIL between 3000 miles oil changes so that eliminates rings and such. Runs great when banging on all 6. About 17 to 19 MPG, a little better on trips, which is nominal for that sled.

lol

Great idea thank you. I have a bunch of those LED Baurima light bars from amazon, was trying to think of an easy attachment method. The bungi cord was just the right idea!

hi ken, it was raining alot this weekend and i left the hood a little open but covered while charging the battery, today i noticed the jeep had trouble starting, if i let go off the accelerator it stopped, do you think water damaged the distrubutor, would it dry off or i gotta change it and the spark plug wires ran smooth...the jeep also vibrated upon startup, rough..but then settled, just wont ignition if i dont put foot on gas, and if i let go off the pedal, jeep stops...

I've got a 65 comet also. Those floors sure were known for rusting out. I'll be fighting the same fight sir. I've posted a video of it on my channel if you want to see it.

I have an extra one from my mustang

Grease in the hub on a regular basis saves a job like that.

Que Acer cuando no está generando electricidad

Do you have to change the valve when your truck won’t stay running won’t idle ?

Off the top of my head, I think rods are 5.565 or somewhere in the ballpark

These distributors last around 10 years. Terrible design. I’ve put two in mine since 2006

A big difference Ken. 👍

After you get the floors done you'll have good standing.😁👍

You're gonna have this puppy done in no time.😎👍

Yep you got that fender looking real nice.

A little bit every day goes a long way.😎👍

UR making a lot of progress Ken . Wow Big difference ! 👍

Ok excuse me top shock mount

Whats the name of that part u needed to tightened you never mentioned what it was the part

Dumbest video ever

What type of grinder is that you are using?