Відео

A lot of negative people now. People need to start and turn off tv and radios to save themselves from all this anger built up over the year's, since 2020 onwards.

Proper job Top work.

Great vid, thank you!

Ive been re-using 3500 elfbar for about 4 months, poundland fluid and a bit of reverse engineering. #works with cbd too.

Drip formers load of bollox how do you go on if its concrete edge ? Start drilling and pissing about ? Or ashphalt edge ? ..... Prewelt your drip fix it free hand the truth Is these chancers cant put drips on with out them love to see them on a proper job with some tricky detail ... Be sat in van nursing there drip formers scratching there heads . ..seen jobs by these people using chesterfelt £30 a roll took enough off recently torch on toms. Thinking there felt fixers . Its cringe worthy

Got any links for this bud

Worked perfectly on my KZ200

Just the video I’m looking for a roofer with this tool can I ask you what are your thoughts and how much are you cutting

I’m doing this exact job on a 2005 CBR 125. I’ve loosened the fork clamp bolt but I just won’t come out and I can’t separate the 2 parts of the fork. Did you have any trouble with it ?

Buy an edge trim ffs with your cardboard drip 😂😂😂

at this point. just get an actual kit

1. How long takes the recharge? 2. Which voltage/amp range does it take safely? 3. How long it lasts after your charging operation? 4. Did you notice any difference in the vaping power after several uses? Nice video but ...

I just put a 3x1 around the drip edge and torch them over then trim to the bottom. Be doin this since torch on came out and is neat and tidy if done rite. Faster to

That’s some black magic shit bro, run and don’t look back

Just bought this bike for 80 pound of a junkie. Its an absolute weapon lol

for how long should i keep the battery in charge? im scared for it not to explode

Do you bot cut the drip first? I find it so much easier doing that way! All you have to do then is nail them up

What is the make of battery charger that u are using

Edgings perfect! Knife is not the best get a Stanley. Agree on the hook blades much easier to cut the mineral just need better weather in the uk been off the past 4 days with jobs stacking up!

nice bike !

Bottom part is different now

Which renthal sprockets u using??

Exactly how I charge it and can u plz add usb c 2 this mate

Bottom hard man

Shite

Do these work on any Carrera bikes? Thanks

You sir are a legend. A man of the people. Saving the world one vape at a time

Where did you get the rear sprocket form regards Jack

On that edge that is slightly raised what wood / battern do you use ? to give this shape on non gutter sides? ___/|

600,000 broke nittys. Incredible

Nice one mate! Where do I get from the welted drips and curbs for the skylight up stand?

Tried this with 3 different sets of pliers, haven't managed to open a single one sadly but I've managed to mangle the hell out of them hahaha

when we cut our flashings we use a plasterboard square, line it up with top make one mark and off you go! just a little tip!

Nice work. What mortar mix did you use?

Quality job mate 👍 #propertradesman

Great vid. One question. Would you do this method on the side where the gutter will be? Or is it a different method. Thanks

Need a proper knife More clouts in the formers very slow way of cutting drips and marking them Don’t need Two men to fix them Use a hammer stapler to fit drips and formers single handed then nail the formers

Drip formers wrong way round, rough side out, get a stapler hammer , put more clouds in former and I'd put a lathe around first so drip sits straight down over facia board.

Thank you these are a big con don't come with 600 puffs bless

Neat idea for charging,now to make it easier,any rc guys trying this, set your imax b6 to .3 amp charge current and hit go! If it fails to start due to low voltage,jump start it by using the nicd or nimh setting on low current again .1-.3 of an amp and monitor the voltage,watch it come up a bit then stop it,leave for a few seconds and do it again,after a few shots and the voltage has made it to 3v switch back to lipo setting at .3 amp and it should detect it and start charging,as with all lipo cells dont leave it to its own devices! Mine charged up fine and i have two more to charge. At that current it doesnt get warm(also checked with my lazer temp gun) mine stayed around 22.3°c which i checked with other things near me so made it an ambiant temp. Hope this helps someone,our charges keep an eye on things but double check yourself. IF YOURE NOT COMFORTABLE DOING THIS BUY ANOTHER ONE!!!!! Del.

The war looks bad U fucks I want my money back

If customers don't spend this is the end result!😊

Hiya, did you tack on the drip edge or was it primed then tacked? Just wondering as this step isn’t showing on your video. Thanks

I was about to give up then went searching in youtube came to this video too and wow so easy to remove. Tyvm for sharing now its done.

first comment

Could some people please give me a follow! Trying to grow my channel to over 1000subs it would help massively, I didn’t realise this video would get the views it has! If just 5% sub I would be loving life I plan to buy all the best disposable vapes and show how to recharge each one! Please follow for more to come

get on the vlogssss laaaaa

Wait what game is that is it gta?

That was funny lmao

This also needs doing on my house 😱