Відео

Should these be set up with compressionless (SIS) housing, or can they use the older style cantilever brake cable housing?

Can you do a video about how to replace the cables please?

Thank you that worked!

Do Gates, make allowances for a the weight the bike i.e. a loaded touring bike.

Wow...what I lifesaver. I had a rear wheel rebuild, switched out my handlebar, etc., and when I got the bike back together, the gearing was totally off: I could only access gears 1-6 on the shifter, and those gears didn't correspond to the "actual" 1-6. I thought I had really screwed something up somewhere and was not expecting anything like this straightforward solution. Bless you for sharing/posting this!

Great video - thanks! I'd really appreciate a similar instructive video on the recommended procedure and step by step guide for adding the gear cables on a Raven Twin with cable splitters and and Ex box Rohloff hub, as if you were putting them on for the first time.

Internal gears typically switch relative to the cable tension & position. Its more obvious with a remote shifter like on the handlebars. The old 3 speeds had a site window to center the cable tension on 2nd gear, pulling it either side of center for 1st & 3rd.

thanks! I had some trouble getting 13 shifts and hence 14 gears out of the shifter box, asymmetrically tightening one of the cables via the tensioning screw worked out in the end.

What brand of rear rack is that?

What a weird design, I'm 44 and I've never seen this before 😮

Part numbers required # 53243 new chain # 12630 eccentric bolts # 16620 new eccentric shell for nomadMK2 # 12076 eccentric tool # 11187 chain splitter needed . Also the chain comes with a quick link . All can be purchased from SJScycles.com

The same way you remove slack from cable brakes.

Thank you. I was envisaging cables going twang and bits falling on the road! Nice design and nice demo.

My brand new Rohloff wouldn't go into 13th and 14th gear, I followed your instructions to the tee (after a failed attempt) and now they work perfectly....Thank You!!!!.........just make sure you follow her steps exactly, I put the cap on before I rolled to 14th gear and it didn't work.... I rewatched and did it perfectly. your video is much appreciated :)

Its a pleasure to see a well oiled machine in action. And no, I do not mean the bicycle. Thank you team Thorn. Every word on the excellent Thorn service rings true.

Can the shifter numbers be calibrated to the actual gear settings?

HUGE thank you - I've developed an issue where the Rohloff is only giving me 13 gears and this very short video (plus the other one of yours titled "Problem with Rohloff gears") has told me more than all of the 15-minute long videos ever managed to do. I do think some mechanics (like computer nerds) make it more complicated than it needs to be sometimes. So, thanks for keeping it simple!

Thank you for the clear and concise demonstration. I'm having trouble getting Gear 14, so this will be my first port of call. I love my Rohloff, but the cable box (X-box, as you're calling it) always seems to give me grief every time I remove the wheel and replace it. Twist shifter is also very "waggly"

Lazy

Thanks for this, I was assuming I would have to take the twistgrip apart, phew!

Would this work for me? Because i cant get my bike into gear 14? Thx

Excellent clarity and brevity

Hey, I have two wires one is black and one is white. It connects to taillight but in which order, there is a plus signal and ground signal on the rear light, which goes where, I tried both ways and it doesnt work, could it be that wires are disconnected somewhere...

Looose couple rides wtf?

Nice one ! is there a video on removing a rear wheel on a Nomad ?

Great help🤗🤗❤

It’s easier if you don’t loosen the pinch bolts too much. Just enough to move the eccentric bottom bracket is enough.

Tune!!! 😎

If it dont have does things