Відео

There is no dB killer to remove . Only the catalyst

@@StavroFix Can you teach me how to get this effect? I tried a lot, but I couldn't do it either

@@nikolozkaulashvili9652 actually that was not my motorcycle. The only thing you need to remove is the catalyzator. Is 4 screws . But you ll need to buy the decat pipe for this location.

Nie trzeba

I don't get what you mean. Feature on what ?

Water feature means like a fountain or waterfall in your yard 😊​@StavroFix

You need to ask seller 😉

Removing the cat I don't think is ok with law. Was only for track days , there is legal. Anyway montage is 10 minutes work!

The place i dropped it was about 2 meters. No issues

@@StavroFix what was the maximum depth of the pump?

@@sowaxl pump can dive whole inside. There I had no more than 30cm depth . If I get your point

A large water fountain

@@nicholasmartin4150 i would say sure it can , but you ll need to adjust somehow the pressure. It is very quiet so is ok for such a job

Always was working , automatically calibrated after few minutes ride each time!

Następnie raz młotek do kotleta i widelec ! Super zestaw na budowie

Ja mam bardzo mała pola, i jeszcze żyje 😜 ale na grube roboty też nie polecam.

Thank you mate 😃

2007-2011 είναι ίδιες. Η δικιά μου ήταν του 10. Η φίσα πρέπει να είναι εκεί.

@@StavroFix A oκ φιλε ευχαριστω πολυ

I think i tried on 0.5cm , not sure i t was long time ago.

What you mean with STL? Still ? If still , then yes 😁

Wesołych Świąt ! 😊 Tak, bardzo tańsze niż orginalne inserty !

@@StavroFix byłbym wdzięczny, gdyby istniał link do elementów złącznych;)

@@sergeysergey911 moje kupiłem bardzo dawno temu ale te zrobią to samo fas.st/nfqkXA Mufa dwugwintowa M8x25mm zapisz i znajdziesz

@@sergeysergey911 teraz przypominałem sobie gdzie kupiłem moje inserty , przez AliExpress było ali.ski/tOa81x 😁

@@StavroFix dziękuję bardzo, zasugerowałeś mi najlepszą opcję))

English ?

No, nothing changed there

No idea , bought and sold like this. Probably previous owner did sth there.

8*18 et40

I usually don't change it ,because it is a trouble , you are right 👍

As you should know, different materials require specific drill bit types and they have an 'ideal speed' for the differing materials. It's all a question of torque... Thus, bench and floor-mounted pillar drill-presses have used the multiple pulley and belt system since the early days of machine engineering. In most applications in which drill-presses are used, materials tend to be either of one type or other - Ex; a carpentry shop where wood is the common material; or a metal-working/machine shop, where different metals are utilised. In the former, it is probably unlikely that the speed would require changing that often; in the latter case, again, speed changes might be infrequent. What is most important thing about the drill-press ? ACCURACY. Minimal run-out/deviation, especially using high-speed drills smaller than 3mm; absolute parallel boring. These are the criteria for such tools and that is most often reflected in the price. Non-belted, geared bench drills are a great all-rounder, but lack accuracy as not enough attention is given to ensuring zero run-out. Great for quick parallel boring in wood/plastic/ even metal, IF you're not too concerned about fine-scale accuracy. Otherwise, I see your comment as simply laziness. If you want an all rounder then go for the geared bench drill (lime-green 710w jobby...). if you're machining metals on a regular basis, then the belted pillar drill is probably a better choice.

Same was to my friend and after 2 months gave the stock back on

I also had wobbling in first days . Try place something hard and straight close to the chuck and press it down to fix the gap. If this ll not work well . Place this hard thing on the chuck and hit it from down with a hammer ( this one fixed mine ) don't ruin your machine but I was not so gentle at this moment 😜. Good luck and thank you for your comment ☺️

@@StavroFix I'm not sure what you mean at all. It's the quill that's loose inside the housing. Everything is fine until you lower the bit into the workpiece. the further down you go the more free play there is. It's a problem when you have an uneven surface because it walks, mainly towards me. I can mitigate it slightly by pushing against it while lowering. Maybe I could put strapping round it or something.

You just need to push it slowly back . Once the one side is in position, then you push all the way around and it fits back again.

😂😂

Truth is, that is not a nice everyday use sound !

Na twardej ziemi, nie da rady tak dobrze , na prawdę 😂 Problem z ta glebogryzarka jest że nie jest tak ciężka i jak jest twarda ziemia to skacze.

Never had an issue with it , contact your supplier. Also check if the plug is well fitted and give some contact spray ! Good luck 🤞

Wczoraj sprzedałem już! Dziękuję 🙂 12.000 kilometrów miał tylko.

This is a friends Moto . He removed after some time . He said that there was a loss of power on high RPM. Second reason his girlfriend on the back couldn't afford the noise !

Wenn ich die Maschine gekauft habe ich hatte keine Ahnung wie eine solche Maschine funktioniert. Mit der Zeit habe ich auch besser geworden. Grüße aus Polen 😊 war ich damals im Region Stuttgart 😊

Without ! The last part of the exhaust remains the same

Enjoy Man !!!!!

Buy a decat pipe . You just have to remove the catalyzator!

@@StavroFixmake a video on how you’d do that for this bike

@@ilucyyou bike is already sold unfortunately. But was really easy as I remember. 3-4 screws and the catalyst is out , then this replaced with a straight pipe!

in simple terms now is a full system (exhaust and straight pipe) they just removed the catalytic converter and conected the pipes. its a fairly easy job with the right tools. tho it is very recomended to retune the ecu of the motorcycle

Lost back pressure. So lost horse power

Ja , mała pola mam , robi swoj praca bez problemów !

@@StavroFix Kupiłem Lidera 80 cm jestem bardzo mile zaskoczony jak nią świetnie robota idzie.