Відео

Hello mate just a quick one where did you get the bearing for this boat . Or size and please mate thanks for the video very helpful 👌

Hi great video is the bearings the same for ND bait boat 2 please

Its not solder fitting its press fitting thats why theres a rubber in there 😋

Do u do a video replacing propellers

Hi mate Great video I see you rewired your boat do you know what the White Connect is called that the main Power lead connects to the motherboard with thank you for any help

Where do you get the bearings from

Great vid i have ND bait boat same problem can you tell me were to get bearings from and part no Thanks in advance

Hi mate would you have a clue why the motor on my bait boat won't stop

Would you build one for my Ranger please?

Hi.its good your showing people how to change the bearing because some people don't know.the rust on the old bearing must be water rust.iv change many bearings I put the in the freezer it shrink them then fit the bearing in the motor housing then give half hour to warm the bearing then fit the motor shaft.i would not hit with a hammer it could crack the magnets.another way grab a socket the same size as the bearing and a extension bar open a vice put a piece on flat wood the put the end of the motor up pressing on to the wood then put the socket and socket and extension bar get i as level as you can then turn the vice until you fill its fitted. Fitting the motor shaft iv never had to hit a shaft in as hard as you did that was a very tight bearing and you had to really hit it a lot to get it in .the only time I use a hammer is to tap the metal lips back over to hold the motor back together.that new bearing sounded to loud to me. Fitting new bearings they must be fitted good if the bearings are not fitted good and soled they will make a noise.A lot of bait boats ware the motor sits at the bottom of the boat and the shaft goes straight out all way let's water in. Some bait boats ware the motor housing and motor fit under the boat there is one rubber seal soon as that seal worn in comes water and that's the end of that motor.i have my shafts on a angle water never gets.in ever.

Hiya I have an old dyna-craft mk2 bait boat I'm trying to restore/ upgrade, I can't find any information on it anywhere. Do you know what size pump/motor it has and how to remove it.? Be grateful for any advice. Thanks Terry

Brilliant mate

I've got an anatec catamaran with very similar motors, and anatec want 90quid for two, what would be your advice for near like replacements, am running it on 2s batteries, might even go 3s if the next brushed motors allow me to, thinking the mtronics m600?

I think my big lake bait boat has normal RC car parts inside it comes Friday interesting stuff thanks for sharing.

i’ve got the bearing number if anyone needs it 625-2rs

many thanks top job my nd just done the same thing do you have a bearing number please

can you tell me how to get the right-hand lever (forwards backwards) to spring back to neutral in all directions as the left lever does please? its doing my head in.

have you read what it stats in the sales write up? I quote Full GPS Autopilot makes finding those spots a breeze, even in the pitch black. Fishing a small hole in the weed? Struggling to find a suitable far bank marker? Got a run in the middle of the night and need to get the rig back on the spot? Easy! Just select the spot from the memory on the transmitter and off the boat goes. When combined with one of the optional fishfinders YOU CAN BE 100% CERTAIN YOU ARE BACK ON THE EXACT SAME SPOT TIME AFTER TIME. THE GPS is so accurate we have managed to fish three rods on the same spot during testing and get them re-placed after dark perfectly, first time, every time. I'm buying a second hand one at the weekend it better be on the money or they will be in court. your advice please, nice video.

Question is, would you start making these if asked?? And how much would you charge to build one ??

can you help me? where can I get a viper x range bait boat door hopper motor?

Great video - where would I get the new bearings from - for a waverunner mk4 with noisy motors so was going to change the motors but may try the bearings first - thanks

Well impressed, now going to build one but from 15mm aluminium tube and a busted rodpod, please can you tell me where you got the mural from in the back ground, thanks,

cool idea I will defo be making one, [ getting on a bit will save me back lol] what frequency is the boat running on only I have a shuttle on 2.4ghz and it knocks out my deeper.

Can you fit the toslon x pilot to this boat instead?

Hi mate I'm looking at doing the extra wire on my boat were can I but the right connectors from??

Nothing worse than dumping your bait 2 feet from the bank when you hit that lever by mistake however the swans love it ! LOL, thanks for the review, regards Matt 👍

I've got the same boat buddy and the GPS is hit and miss ..you can't clip up to the same spot as it misses it by a quite alot ..and the feeding the wires through is a right pain lol but all the rest is spot on 👍

How would you bild one for the lake reaper that dose not ave the lip around the front or the side of the boat thanks😄

Hello pal, nice stand! What are your thoughts on the deeper boat mount? Was thinking of buying one myself.

Hi there. Love the great idea so I built one for my mk 4 waveruuner . The only thing. Did extra quick-release legs. Thanks for great idea. Top man

Top man great job

Nice job mate. Impressed

yes indeedy i need one for my AT standard baitboat.

Any chance of doing a video on the cult ranger it’s self

Cool👍