Відео

Is the torch still going strong?

A little bit of oil in the collet will help it work smoothly

I learned how to load it but mine is not sending the black bullet loader back up hoping I don’t have to open drum up now

It holds 2 cups of kernels

So it’s been a year, are you still happy with your Milwaukee concrete vibrator?

I’d wondered if this could be done with those wrenches. I knew Snap On and Pittsburgh both had ratchets that would.

I know this is an old video but is the vinyl tubing simple to replace?

Thank you very much! God bless!

Almost got sold one of these, glad i didnt buy. Ill just stick with carrying x4 22 round mags 🙂

how did you pair the remote with the receiver?

Hello Perry, how did you cut the table to fit the stovetop?

Nice review. Any problem with the Spyder bit jamming like a spade drill will do?

Do you have to wait till the oil is hot? What’s the result if you just empty drop everything in at once?

Man that's a nice torch. I love my niner too. Precision and quality is awesome.

Thank you for this video,,it is really informative. What is the sizing of the tubing connecting the outlet valve to the water? How long can i use it to pump?is it 30 minutes,1 hour..??

😩 Promo_SM

What type of lubrication do you use in your popcorn machine motor? That spinning motor needs lubrication when it dries up! It will make noise.

Excelent

This is the best thing I've seen since ice tea! The only correct solution for outside bib! Security and absolute peace of mind!

I’m in contact with a UA-cam channel that uses Flex regularly in real construction projects. He said that the Ryobi impact driver and impact wrench are legit.

You’re not using it right. You have to put a tube on each outlet

I’m wanting to put one in, I have metal siding and easy enough to drill out. I have a plethora of tools so that’s not my issue and your demo is the only one exactly like mine in that there’s almost no room in the basement up toward the ceiling or on the sill plate (sorry if incorrect name for it) but I’ve wanted to replace my normal hose bib whatever it’s called with this Aquor system because for whatever reason when I turn my water on it’s not only difficult (I have lupus and hand strain is a real issue) I also hear a horrendous sound and it sounds like the pipe shakes too. Ik when my bathroom was done 8+ years ago one thing the contractor recommended was a new hose bib (again sorry if I’m saying incorrect names for things) so he replaced it and prior to me knowing about the Aquor system. That’s when I noticed how hard it was to turn the water on and off but the same sound existed even before. Anyways I’ve done several jobs with plumbing now but I’m hesitant to change this sucker out because idk will this Aquor stop that awful sound or make it worse, is there a way to control water pressure as needed and there’s almost no room without drilling through I’m sure important wood structure framing to replace it. I could be wrong on having no room but I noticed this Aquor leans slightly downward in your situation so that could present problems for me too. Sorry lots of questions but it’s hard to find examples like mine

thanks for the quick video

Thank you for posting. I noticed when you clicked the magnet on the wall plate the laser slid down, are the magnets strong enough to keep it from sliding down off the wall bracket?

Come on really !

Good video! Thanks for sharing.

Got mine from Amazon.CA ..., was like $90 Canadian. If you're as tired as I am of banging nails out of reclaimed pallets? Highly recommended! I also picked up a "Pallet Buster".... I've been salvaging pallets for YEARS and my life got a whole lot easier with these two tools. Wish I had acquired these tools earlier! BTW, the ONLY pallet buster to buy is the one with the "swivel heads' on the end. They lift the board out straight from the runners without leaving a huge set of divots on the underside of the board. (The side most often used after planing because of the smaller nail hole)...ONE OTHER THING: IF YOU DON'T WANT a huge divot where the de-nailer slams the nail through....just hold it away from the board so the drive-pin doesn't ruin your board. /wink --- Pallet Buster: www.amazon.ca/gp/product/B00JH41U7M

So is it worth the purchase ?

Your write up was a wealth of knowledge, far greater than the four minute video to back it up. Who is she would do more instructional videos

Does this air pump last a long time and where can I get it

Thank you sir!

Great video, never saw one of those, was only a maintenance machinist for forty years, very interesting but too late now. Thanks for sharing.

Get a HP battery for that thing and it'll have even more power

Anybody know where I can find replacement tips that fit?

Thanks man! I was confused about changing the tip so Thanks!

Cool. I have a hf one. Still waiting for a situation where it's needed.

It doesn’t fit

Where did you get your hard hat strap for the light?

It’s barely visible on the ground but overhead and on the wall it’s great but yea that’s only downside to this laser

👍

How did you open the Weller box, with the plastic pin that held it closed

It doesnt lock in place. Its a pile of shit

Putting the bolt in is cool, but what about breaking it with the indexing wrench? What would differ this wrench vs say, an s-shaped ratcheting wrench?

How r they holding up? I'm currently looks for sum lights.

Numax where you get it at?

Can't wait to get mine. Being a electrician there is usually only one laser level on the jobsite for us. Right now we only have a 6 point bosch laser level. It works but its nice having the horizontal line and vertical line as well as the plum dots for laying out lights.

How did you make it ?

The only thing I really wish they had done in the wall hanger was to put a rivnut 1/4-20 tripod mounting screw. Perhaps I will attempt to drill it and put in a Plus or Riv nut.

I have one and it fits great guess it depends on the phone and case

It never seems to amaze me how dangerous some of you wood turners are, gloves when turning. Skin will give the glove won’t and sooner or later your going to find it out especially when you keep grabbing the wood while it’s turning, a good video on how not to do it