Відео

Make sure you put the fuse back in the right spot or that the fuse is still good.

ya, even tried the spare fuse and no luck…yours just worked right away? Did you put it in the water?

@odubbya right away. Didn’t put it I. The water. Is the IBR light on on the dash signaling there’s an issue with the IBR system?

No lights or anything, just stays up..

Retrace your steps. If the Ibr light isn’t on on the dash then it’s not an issue with the fuse. You have to rev the throttle a bit to get the ski to engage into forward mode at which point the bucket will move.

So glad to hear it brother! Thanks for commenting

Thanks for commenting! Makes my day brother

Great video, I did this and it worked but now I can't get the bucket down when I put the fuse back in, any tips ? My Ibr light came on

@@markfitch8617 double check you put the fuse back in the right spot, it’s the bottom right corner. Also verify the fuse is still good. I just did it yesterday and put it in the wrong spot initially, then the IBR light was on and was beeping at me. Once I put it in the right spot it went away and worked right. If it indeed is in the right spot and still not working check trying unplugging the battery for a minute or two. If after that then trace wires for loose connections. After that Id suggest taking it into a shop.

​@NykevOfficial thanks so much!

Yes it’s definitely a torx

@@NykevOfficial is it a torx 20??

@@chinesejohncena9137 most likely. It’s a very common size.

@@chinesejohncena9137yes torx 20 another comment already stated that for his 05 Acura he needed to replace the bulb

Either. Drive 50 miles and it’ll drop off or use code reader.

Haha that made my day! Hope it was helpful brother

Trynna figure that out rn too don’t think so. I think he’s doing the passenger light in the video

Yo! The video is showing the drivers side and yes I did this same exact method for both the the driver and passenger side and it worked pretty much exactly the same just with things mirrored. Good luck gents

You can but the driver side black cover is a much tighter fit. I managed to do it today but man felt like I had to wrestle it in there. I recommend taking the whole fender off around the wheel makes it easier.

Yes Just did it yesterday. Very doable just turn the wheel towards the inside of the car of the side you are working on. If you have large hands might want to take the wheels off.

Screwdrivers, torx bit, pliers, that’s about it

Ignition came with the bike

Thanks for the feedback brother Glad it was helpful

No longer have the car but the bulbs last pretty long. I did have an issue with flickering and traced it back to the igniter cable. Swapped that out and good as new.

Oooh, great idea. Wish I would have thought of that one.

Great idea on removing the tire. I didn’t even think about that.

Great suggestion!

That one got me too at the very beginning, was why Included it for sure

Dang, good luck.

Glad to hear it brother! See ya outside 👌🏽

I had a flicker headlight issue as well. Turns out it wasnt my igniter unit itself but was the cable. It would flicker every time I hit a significant bump in the road. Try tapping, wiggling the igniter cable to see if you ran reproduce the issue. I’ve learned to always zip tie/fasten down loose cables. Overtime the vibrations from driving bend the wires until they snap.

Hmmm potentially, question is where to source one though… and at what price

I don't think so, because I replaced my whole assy and it was streaking as bad as his was in the beginning of the video. The new assy was no better than the one it replaced.

Correct, now that I think about it a newer tighter spring wouldn’t make any difference because the spring wasn’t the issue. The issue is that internal arm being too long and not allowing the arm to articulate far enough to reach the window.

Sounds good. If you like let me know how it goes, would be curious to hear your experience

Just went down to get the set today 😂🤣 Shis a pain in the ass and I gotta fix the passenger side headlight

Yeah I may have taken the battery out to, definitely is a pain

Glad it was helpful! And yes, definitely a pain and not the greatest design as far as serviceability 😅

Yeh can't believe this b.s ! Whoever designed this crap and decided to lock it with that pin screw needs a beating! Once I take that screw lock out im not even gonna put it back what nonsense terrible pita!

Verify if the bulb is good or not. If good then verify if you’re getting power to the connector. And then go from there

Appreciate it brother! Hope it was helpful

Thanks Hahaha I’ll be honest that’s the work/don’t care jacket and I run cold and hate being cold and that thing is real warm. Good luck with it. Feel free to let me know how it goes

Yo, sorry for the late reply. The high beam on the TL isn’t actually a different bulb but the same one. To achieve the high beam there’s a physical flap that rotates out of the way to let the beam shine higher. When you engage the high beams you should be able to hear it. If you can’t hear it then sounds like it might be malfunctioning.

Agreed. Why I made this video to hopefully make it a little less painful

I believe it’s actually a torx 24 or 28 or something around there

Torx 20 Security screw on my 05. Just get yourself a WARRIOR Security 33 Piece bit set from Harbor Freight for $6, has all the sizes you will ever need. Also make sure you have a short screw driver that can take the extension.

Creative, solution for pulling off the splined rod, well done. Glad it helped!

Yes that’s true won’t always work, but if it’s too long then my next suggestion is to file the wafer down to the correct height. If it’s too short though then yeah gonna have to either remove it completely or replace it with a different one

Google the part number. Product listings can change over time but part numbers never do. I bought mine straight from the dealer.

Haha well don’t live under your privileges! You bought the car, use it up! The switch is on the front wiper stalk, it’s a ring that you rotate instead of moving stalk up and down.

@@NykevOfficial you know I won't remember that. It rarely rains in California except for this year. I recently found out how to turn on the fog lights! I showed my GF how to turn on her 2001 4Runner fog lights and she didn't realize she had those!

Interesting! Let me know if it did!

You’re welcome! Glad it helped

Solid

Glad it helped!

Yeah good question. I’m sure there’s some sort of rhyme or reason to their designs and locking coding but if I were the manufacturer I wouldn’t necessarily want that to be public 😅. Glad it helped!

Oh really? How come. I was able to do both sides so curious to know the issue you ran into

No problem. Glad it helped

Glad it helped!

Could be a bad bulb, igniter cable, or igniter itself. Recommend swapping out those parts one by one with a known good one to troubleshoot.