- 55
- 17 532
SLC Radio & Cable
Приєднався 20 гру 2022
CB radio sales and service
Kenworth W900 coax and radio install complete
In this video we are showing the completed install on this truck.
Переглядів: 145
Відео
Kenworth W900 coax and radio install.
Переглядів 129День тому
In this video we just wanted to show the install on this truck, hopefully to help anyone who maybe wanting to do it them selves .
Fractured solder joints
Переглядів 115День тому
This video is just to show that not even new radios don't have problems, and what may cause your new radio to fail.
Ranger RCI X9 cranked up
Переглядів 792Місяць тому
This video is to show how some crank radios, which causes excessive heat and all kinds distortion.
Stryker 497 after tune
Переглядів 300Місяць тому
This video is to show that the Stryker 497 is very capable of achieving 100 watts of power and still have nice clean audio.
Stryker 497 fresh out of the box
Переглядів 379Місяць тому
This video is showing what a stock out of the box Stryker 497 looks like
Brand New Galaxy DX94HP Tune up report
Переглядів 1522 місяці тому
Brand New Galaxy DX94HP Tune up report
Ranger RCI 39VHP PLUS
Переглядів 1062 місяці тому
Customer ran radio with high SWR and was concerned about damage that may have been done. NO DAMAGE FOUND
Galaxy DX88HL
Переглядів 4003 місяці тому
Quick view on mods performed and the results on how they perform
Connex 3300hp tune and aligned, also showing proper analyzer results
Переглядів 3063 місяці тому
Connex 3300hp tune and aligned, also showing proper analyzer results
Just showing how DX Radio shop keeps moving the goal post
Переглядів 1 тис.3 місяці тому
Just showing how DX Radio shop keeps moving the goal post
Why bias should be set by current and voltage
Переглядів 2464 місяці тому
Why bias should be set by current and voltage
Galaxy DX44HP Repaired / Up and running mint
Переглядів 5354 місяці тому
Galaxy DX44HP Repaired / Up and running mint
Stryker 447hpc2/All cleaned up and running mint
Переглядів 7199 місяців тому
Stryker 447hpc2/All cleaned up and running mint
Stryker 955v2 follow up after mods removed
Переглядів 1,6 тис.9 місяців тому
Stryker 955v2 follow up after mods removed
Cobra 29LTD Chrome Mod remove and repair
Переглядів 1529 місяців тому
Cobra 29LTD Chrome Mod remove and repair
Stryker 655 follow up on channel selector
Переглядів 19210 місяців тому
Stryker 655 follow up on channel selector
Very Good Video, Nice and Clear. Great Job, Thanks
I was in a house once in Florida and I thought someone was outside on the property and it ended up that the exhaust fan in the bathroom was picking up shortwave radio or CB and I thought of that episode of Gilligan's Island where his fillings caused him to pick up a radio station.
seeing that open reminds me of pulling them apart when i was in my 20s and adding extra channels and tweaking the power ,,, i probably ruined a few in my time bud i did succeed at extra channels a few times with no issues ,, do people still talk on the cb anymore ?
Yea, on 10 meter rigs converted to 11 meter CB freeband illegally like this guy does
@@timesup6386 Wake up man, The FCC does not give a SHIT about ham radio or cb radio. If they did do you think they would allow high power splatter boxes from rci on the market? Hell no!! There is no money in it for the criminals in our wonderful government. Stand by LOL.
That’s a clean radio! What year is that?
You have a nice setup! Neat and tidy for sure!
Good video and sharp eye! Quality is questionable more often than not on most radios. They are all about the same, manufacture wise..most coming from the same factory.
Nice truck
I heard of people doing some kind of mod that boosts average power
Nice work
How would I be able to send you a radio and would you have time to work on a radio? It’s a superstar older version upper and lower side. It is out of whack.
Best thing to do is give us a call @ 603-732-3175 So we can discuss what your looking for
You got to know your fighting a non winnable fight!.. Do what YOU do and make it known to Your customers that if a problem comes up from your work, you would like first chance to address it to make it right in Black & White! I think that is about all you can do. "SOME PEOPLE" just can't be PLEASED! Good records kept on each job is PRICELESS! Got a Ranger that needs looked at as soon as the budget allows! in Colorado 73's
I enjoy your videos, thanks for showing your work. Learn something new every video. Keep on keeping on brother!
Thanks pal..here we are just trying to help people out and prevent from getting taken from there money
@@slcradiocable641 People always have something to bitch and moan about 🤦♂️🙄.
Do you do anything with the receiver on these or just go with factory?
Good morning sir We only do adjustment if necessary. 99.9% of the time there in good conditio, no need to touch them
3/4 if what was said in this video is wrong.!!!!!
Really Why don’t you explain, I’m sure everyone would love to know what you MAY know
@@slcradiocable641 I did explain, you can't have over 100 percent modulation and this can not be denied regardless of how you try to spin it you bonehead.
A myth...lol lol your no tech ... Anyone that claims the 54 mhz trap circuit being a myth is a damn fool and sine of someone who has zero understanding of RF and transmitters...the 54 mhz trap is directly there to keep the 3 Rd harmonic out of the TX signal ..Lord go back to school son
Anything over 4 Watts is Illegal.... Would not want to get caught...
The NPC mod ....if set up correctly....is a very clean modification. The reduced carrier is one of the keys to the mod...there is no benefit whatsoever to running a high carrier....a high carrier is useless unless you like an overly warm radio. I keep my rangers around 150% modulation and they all have a clean sinewave and very acceptable harmonics on the analyzer. Even the FCC allows 125% modulation on commercial AM broadcast stations so obviously over 100% mod can be done correctly.....and not a dirty signal.
Makes you wonder why other radio shops refuse to show spectrum analyzer and line scope on customers radios they to claim to tune up. One shop charges customers $25 for a tune up report video and all he shows is watt meter.
The customer asked for that radio power to be turned down to 60watt.
Good morning and thank you for following the channel.And no I don't believe that's a fact, if you notice the video and description have been edited (you would only notice this if you saw the original). In the original video he stated that the radio was set up PER MANUFACTURER SPEC. Put all that aside, if he was setting it up for an amp, any good shop would have had the amp on the bench along with the radio to be sure that they where matched together.There are too many variables in setting up a radio with an amp, you just don't say a radio is set to run an amp and let it go, this is why so many people blow up there amps. Also keep in mind every radio and amp (to be run properly) are set up in different ways. Just for example a 2 watt carrier could over drive an amp's output carrier, which would cause it to run hot and eventually cause damage. And the shop you are referencing, doesn't even understand the proper way to set FM deviation. Again thank you for following my channel, and giving me the opportunity to bring such disinformation to my followers who wish to see and know the facts. Regards, SLC Radio & Cable
@@slcradiocable641 Were talking about video on DX radio shop right. His latest video he mentioned that the customer requested him to not say why he was turning that radio down, he wanted to mess with a troll and DX agreed. I have only watched a few videos from that channel. I don't know much at all about his work, i was just watching some videos on Stryker 497 (i recently bought one).
How is the radio doing so far did you leave it stock out of the box I've been wanting to get one but I got a striker 655 I don't know if it's worth the extra money or not
@@jamesdean165 I got my 497 from a different radio shop. Only thing done to it was aligned/tuned. I wouldn't go from 655 to 497. Maybe 955, if you want USB/LSB to talk DX.
Thanks @@ryback6060
Where are you from?
We are located in in New Hampshire .
📻🎙️🎙️🎙️
Can you do a FOTB on my 69 that you got waiting for me ????
great news 👍👍👍
🎉
Nice vid
Keep up The good work
Thank you sir
If any custom PCBs can help? Open to sponsor! (PCBWay zoey)
😂 4 to 1
Omg
What’s your problem?!
😂😂😂😂
If you come to by CB shop again and slander me I will get you for defamation. Stay off my review on Google and Facebook. This is the last warning. I know we got you figured out with little help from some people. DX radio shop has been in business for 38+ years we do everything BY THE BOOK!!!
Keep up the good work👌
Thank you for not carrying on all that stuff that’s going on. I see you are a good tech. Keep moving forward.
Thank you sir ,we are trying to avoid it the best we can
Longer Coaxial Cable.....
That always fixes the problem...LOL
I am hoping those 88’s are still there when I drop mine off so they can have a “Family Reunion”. Mabey it will work as good as my unrepairable Superstar.
you have great work ethics keep up the good work
👍👍👍👍
Have a general Lee that has stopped working. Can I send it to you?
You sure can, give us a call any time .....603-732-3175
Hey brother I wish you a happy 4 as well
Right back at you sir..have an awesome weekend
I call for a truce
None of this would have ever happened if DX radio shop didn't find it so important to keep mentioning my self and many others in his video's. Most others just sit back and take his bashing (as I should to) but as I have said in the past, I'm going to defend my self and unfortunately in doing that i have to bash back.
You are awful!
I think you're both acting unprofessional.
You’re absolutely right … but here’s the issue He finds it to be important to throw people under the bus when ever he see’s fit. This man DX Radio shop, started all this crap weeks ago. And I’m sorry but I’m not going to sit back and just let him walk all over me. He doe’s this same thing with a lot of people, he starts the fight and then blames it on the others guy
I don't really understand. I'm guessing you're testing with 50kHz of signal bandwidth? 200Hz up to 50kHz? That's well into the ultrasonic range. Not really sure what the usefulness of that is. All that matters is that you get clean signal without a lot of spill. Physics always wins.
Yes 50kHz bandwidth, and yes i know that's quite a spread, but it's only to show to people the difference in the power gain on the watt meter from a radio that's been cranked or clipped and a radio that's set up correctly. And yes I could use maybe as low as 20kHz, I just choose to use 50kHz,this is all just for demonstration.
nices radio I got the big brother 69vhp rci
he a clown & clown are always stupid he like making himself look like a fool that he is already
I find that any shop that bashes or bad mouths other shops are just as bad as bad shops DRAMA QUEENS STAY THE FUCK AWAY GOLDEN SCREWDRIVERS!!!!!
Agreed 👍🏻
I’ve been telling folks that for years. No one listens
What’s that mean???
CB Shop guys trying to get their ham license overnight lmao!
I’ve really been enjoying your videos. I like your outlook on tuning these radios.
Thank you sir… we are trying to show how it should be done for best performance and longevity