Відео

How tight were the bolts that held the bed to the frame?

Thanks for the video got Bullnose I need change bed on.

I have one like that with an Onan. About 50 hrs total time. It is a little fussy to start after sitting awhile. I usually have to prime it with starting fluid down the carb a few times before it picks up fuel on its own.

I used to be a Ford Tech this is way cool I had no clue you could do this. I am restoring my Moms 91 I lost her in 2017 the truck has been on the back burner for years out in the weeds I have had just too mnay projects . Somebody ran a red light and plowed into my GMC so been with out a truck so this I why I finally started on it . Thank you for posting love thje video. How did you learn how to do this ? Was the bolts rusted on the bed

Lost this channel for a while, hoping to see an update on this rig !

thanks for posting this. very helpful

how much do you think the bed weighs?

👍🏻👍🏻👍🏻👍🏻👍🏻

Fuel goes bad in 2 or 3 weeks, my friend...

Any more on this truck? 👌🏼

Takes atleast 10.5V while cranking for the injectors to open up. Good cranking is always important for these engines. I know it's almost a year old video but it's good to know 👍

I use Hot Shots Everyday treatment in my Diesel fuel

How do you like the b/r trailer? I see they are affordable, but will they hold up over time.

outstanding

When you have to use starter fluid, spray some WD 40 after to help it have some oil to your piston ,

Use Thompson water seal and mix 50 50 with diesel, Spray it on with pump up spray tank, will make it last a long time and Redo as needed, also on bottom of truck use 1/2 coffee cup of Dawn dish soap, 1/2 gallon of water, One gallon of Diesel, Shake well, Spraying bottom of pickup for three or 4 days, depending on the rusty parts, spray this on will make the bottom look like new after you presser wash it off, on mine did this everyday for about a week, It was on a trailer and took it to the car wash and it looks great now, Did this in the oil field years ago,

You supposed to remove all orings and gaskets before you spray with carb cleaner

Carburetor cleaning stretches orings

Had80. And too 85 96and a 97tell me.....

Great video. Ty

I dont know if you were in the army..but thats exactly how i used to tie down my dozer in the rear

What’re the chances you could send me a video of the wiring for the potentiometer? My 10,000 has no output and the potentiometer was broke. I replaced it and cannot find the pictures I had taken of the wiring to the control board prior to disconnecting it.

on my car trailer I used deck paint. it has grit in it, and it sealed the wood. seems to hold up well, had it on there for 2 years without anything peeling up or anything.

Thanks man!

I made the mistake of buying a used Pittsburgh engine hoist that was to short for my 92 f150 extra cab long bed the arm hoist didn't reach to the middle of the bed it was a pain in the bud but was able to remove it to replace both fuel pumps now putting the bed back on will be a different story 😅

Did you replace any components of the dual tank harness?

Nice video.

Great method. Must do this on mine. 8 ft bed though. I own an engine lift !

Try adding pressure to touch fuel tank while cranking...

That no oil pressure/long crank issue is the low pressure oil pump not being able to supply enough pressure for the hpop. Melling makes a much better low pressure oil pump for the 7.3L. Just make sure you grease the gears of the pump so it helps with priming. The gauge on the dash is reading base oil pressure only (low pressure).

Do you have a part # for the Carb you ordered?

You didn't show how to remove them bolts plus you filming against the sun the holes also no information where is the harnes for the tail lights and how to disconnect them..... wasted time

The flashing OD light is likely the TPS. A functioning tach sensor is necessary for the TPS to work properly. I had a bad TPS and tach sensor on my 1993 7.3 IDI that dogged me for years. When the OD light flashes the truck goes into limp mode. Another possibility is the speed sensor. All three have to be healthy and the TPS adjusted correctly for the OD light to quit flashing. Also the TCM capacitors are known to go bad which will throw error codes so the OD light flashes.

I'm in NY and bought a "1994" F150 that came from Tennessee. I think it's a junkyard Frankenstein. When I went to buy new front brake calipers, my calipers were held on by slide pins. But all the 1994 calipers were held on with two bolts. I figured out when servicing the rear universal that the tag said 1992. So what I have, I think, is a 1994 body sitting on a 1992 frame. I guess that means I have a "unique" vehicle. But, like you, I have leaky gas tanks and bad sending units. So I was wondering what could I do for tail/brake lights if I decided to leave the bed off and drive around like a flat bed? Are there kits I could splice in or plug into the existing wiring harness that you've heard of? I guess I'd have to bolt them onto the rear frame or something.

Use a comalong inboth loops , hook it to tha back bumper and tilt it over

donde consigo uno

I always say to the ol lady "would you rather I have a project or a side piece it's up to you"

When I the sound a diesel car running my blood also runs,I like diesel sound like nobody,s business.especially from Ford ranger trucks like F100 up wards,I own a Isuzu KB 2,5diesel but dream one day I will have the f 100orf350model 1990 to 2000🇧🇼 from Botswana

Thanks for the great video! Keep it up.

You the man 100

Beautiful truck 🇧🇼

That wheel super crooked when you’re driving straight. You can prob take the steering wheel off and realign it. Only has one nut behind the horn holding it on

Led 3rd brake light can cause transmission issues as well.

I used final charge pro series coolant in my 93 idi. It’s supposed to protect against cavitation , liner pitting and water pump corrosion and is good for like 3.5 million miles supposedly. I’ve had zero issues with it thus far

Sometimes these ol 7.3 need both batteries and typically require a lot of cranking amps. Prob help to hook up both idk

You need a bigger diameter hose and shop vac. It would make it a lot easier but that was definitely a rough one. Must have been some squirrels

lol at the wife part! My wife ask me if we are going to have a used car lot as a front yard

My 97 f350 had the issue with the third brake light bulb was blown and a diesel shop wanted to put a new tranny in it. I did some research and for 2 bucks fixed it with a new bulb.

cps and check fuses first as there's some stuff that run off the cps fuse

Thanks for posting !