Відео

Do you have any idea if they make a replacement screen mine went out on my remote .So I can replace it.

My tv starts and is working fine but after an hour or so it just turns off. Do you think it is the same issue?

Looks great. Which stepper motors did you use?

Yeeeeaaah. I’m just gonna send this thing back to the retro store… I have the tools to do it… but this is a lot of sticker piling and screw outing just to get to the lens to clean it 😂

Thanks man, you saved me in 2024 Worked with my sa ct370

This video saved mi TV, thak you so much!

What if your tv has vertical lines? I mean they're barely noticable but theyre right donw the middle. How do tou fix that?

Only reason I was tryna watch was to see how to take the speaker off the x540 and you cut that part

I no joke have the same LG TV but in the 45 inch model and the HDMI ports have broken off for me as well. You’re much smarter than I am so it looks like I might just have to be in the market for a new TV 😢

How did you know the usb charge port was your problem ? I’ve done ohm tests on all 4 of my solders to the circuit board and they seem to be communicating just fine. How did you know that was your problem ??

Glad I looked here first, save a buddy $50 for a $0.50 cap. Thank you

Instead of using dowels, I assume you could just glue the pieces.

The video is pretty cool, except for the music. I had to skip over the opening demo.

It stopped updating like where it says verifying would that also have anything to do with the hard drive?

M2 screws!

@vantzis

Very informative and interesting. Thanks for sharing Ben

But my guy, disconnecting things doesn't repair anything. That cable is there for a reason. I don't see much troubleshooting here actually.

You can roughly explain what was technically done. Is the circuit feedback cut off? What is the reason for the malfunction? Is the board current low? Or is there a fault in the display matrix? In the event that we do not know the solution with pasting, which part must be replaced? Your fix worked, Thanks.

Gorgeous work!

Yoo

You could probably make this a bit better by having multiple options for drawing. You could use less memory to draw complex shapes For example, instead of just being able to draw a line from point A to point B, you should add a small flag (a handful of bits or a byte for ease of coding) that tells it if you want to draw a line, Bezier curve (quadratic or cubic), or arc between the points. if you specify a line, it will expect two points to follow if you specify a quadratic curve, you can expect 3 if you specify a cubic curve, you can expect 4 an arc could be defined in multiple ways. An easy one for this application might be 2 "root" points for start and end, and a 3rd point somewhere along the arc. Then, you could easily calculate the points along the path in the arduino which uses far less memory than storing all the points beforehand. In fact, fonts are stored as lines and bezier curves, which means you could have another flag for text with a start (x,y), the length of the text (chars) to know when to stop looking, the font size (and name/ID if you want to be fancy with it), and the actual characters to write.

Nice out of the box thinking here. Great job.

3:58 can i connect both the ends of a same strip to two different switches. Situation can be, either of the switch is powered on OR both of them are powered on at same time. Will it cause short ckt or any other problem? In your ckt diagram, you have connected only one end of the LED strip.

Writting support comment. Was here before 1 mln views.

Chuck them in the bin and just get some proper cans.

How did you get it apart

I use this workaround in a Samsung TV 32” and it works. The PWR BLU was the same, number 6, but the connector has more pins. Thank you so much for sharing it.

Do you recommend using the hot air gun Was that flux you added in the video

Damn, i owe you a tv man, thanks.

Kinda reminds me of replacing the digitizer on an old android (before they started gluing the screens down.) I used to buy the replacement parts on Amazon for $20 and do all my own phone repairs. If you're pretty handy and pay attention well, you should be able to do this! 💪😎

Unfortunately, the average person would not be able to do this. How much would this repair cost on average?

Thank you for this! the TV works now, but not it’s overheating from the tape, what should I do?

My 75in model #qn75q60taf went out a few wks ago and samsung told me $600 to fix!! Of vourse i declined and bought a new 75in for half off. Thought i got a good deal but wish i wouldve seen this prior!! I still have old one so im gonna buy board and if it works sell it!! 🤞🏾

The world needs more yous broooh big up, I may not be able to fix this but the knowledge is enough for me 👌💯👍

Can you replace the entire LED strip if needed?

What gauge wire is that on the internals?

Holy shit baked mine for 8 minutes at 350 and it works again

I just get a blue backlight screen, no matter which pins I'm taping :/ help please! The blue Screen stays on when I place the tape on a specific part on the pins.

ice cube tray - genius.

Worked thank you very much for this video

Can you send me a controller

Bagaimana kalau display nya tidak menyala...? HT-CT780, sudah tekan tombol Dimmer pada remote, masih juga tidak menyala. Jadi tidak bisa pilih menu WS...?

What's a DVD player...