Відео

Amazing video. Love the Trigun theme and also the fact that this thing is so easy to disassemble. Thanks mate.

finally someone provides excellent explanation of ratio's calculation. thanks

Great video! I have a long-running fear of taking apart anything vaugely mechanical, and a long history of things going wrong when I do. I was able to take apart my CM.028, swap out the gearbox for a polarstar box, AND get it all back together with no extra parts! Truly a relief.

My rear sight block pin will not come out!

Thank you

How did it get to rare so fast

So what would be a good motor for a stock build gun, if i didnt wanna hear the whiney noises of the stock motor? Like, whats a good switch that wouldn't cost much but will make the gun more efficient with both fps and rps?

BRUH all my SHS pistons strip! Now I only use REAL DEAL Performance Pistons.

Tips from me: Check the radius in all view, basically 3D. because if not, it may look radiused from outside, but in inside, there are part of the gearbox that if we consider 3D direction of crack, it still needs to be radiused also. It may complicated, but typically, radiusing with 2mm diameter diamond file until it form 3/4 circle is sufficient. 1/2 or less is inadequate

What if I did a 16.1 with a M130 spring ?

Great explanation video. I'm looking at building a faster rps and trigger response. Might buy a boneyard to attempt as I've never taken an AEG apart

What do you Think about changing my 18:1 to 14:1. I already got 1.95jule on m130 (Peru n hybrid v2) and asg 22k motor. The trigger reaction is awesome but i would like to shot Faster in full auto Mode.

Nice video. I´m entire day searching for something like this. But I have question hope you can reply. I´m going to have p90 from cyma. Soooo I want it high rps. So I´m gonna buy 11.1v battery, 13:1 gears, soft spring (I have cca m90-m100). But I wonder what motor. Motor at what rpm should I buy? I heard 18k-22k but that was only one comment.

How do you make a gun from zzzzzk to chk in semi auto

Dude you NEED to make more video content!

Will you make a updated video adding brushless motor in the mix here to see how they stack up?

how bout the rear window. should it be radiused?

Great Video ! Greetings from Argentina 🇦🇷!!

hello friend I'm a newbie in this stuff, should i remove some teeth for building a DMR?

you don't know how much this helped me. thank you so much!

I highly recommend that all you do is make your gun the best it can be. If the part isnt broken, don't replace it. Leave the dsg's to professionals. In fact if you want smdsg rate of fire, it might be easier to hpa your gun with a p* or wolverine.

Nice!

could I get the best of both worlds by buying a 11.1 lipo with high torque engine, high speed low torque ratio gears and a powerful spring. also could an all round higher quality motor have more toque and rpms?

I thoroughly enjoy everything about your informative videos. A professional and intellectual lecture that is both scholarly and basic in its form. Thank you immensely! P.S. The music makes it even better!

Okay, sorry, but this is so half-assed. You should be using the dremel wheel to rough up all the surface areas of the rack that contact the piston when inserted. Also should be using sand paper or a sharp tool to rough up the rack track in the piston. And then after all that, its CRITICAL that all surfaces are free of any oils. I use 99% rubbing alcohol to wipe everything down several times. You can wet some paper towel with 99% and use a small flat head to thoroughly clean out the rack tracks. Also, for anyone watching, never use grinding wheels indoors. That dust gets everywhere. Including in your lungs if you don't wear a mask...

Just a tad bit of advice, show off the before and after clearly to the camera. As a viewer, you basically cannot see what the finished look should appear as with the cylinder installed.

Hi! Do I need the sector gear delay chip with the 12:1 gears?

Severely underrated, mate you're a life saviour for an empty headed bloke like myself.

This is the greatest channel I’ve ever come across when it comes to tech tips

Thanks to this video I figured out that I accedentally bought the same hear set that was stripped by tension so now I have to just replace the spring entirely lol you saved me more than you cost me

I had this piston for 2 years and I just learned that I had to epoxy the toothed rack. I feel so stupid now

my brain just got bigger

Funny how an anime about guns uses this intro music

I have no idea what I'm watching. I'll finnish the video out of pure frustration.

And about the 100:200 and 100:300 gears sets?

ty

ty

Hello can i ask you guys what type of mosfet do i need for my Specna Arms Daniel Defense® MK18 SA-C19 Core™ i will put an 35000 motor in it and i will use a Lipo 9.6V 1300mah Battery? Thank you from Croatia

Hello can i ask you what type of mosfet do i need for my Specna Arms Daniel Defense® MK18 SA-C19 Core™ i will put an 35000 motor in it and i will use a Lipo 11.1V 1300mah Battery? Thank you from Croatia

Ok so i’m doing a trigger response build with these parts: SHS 13:1 Gears SHS High Torque Motor SHS M130 Spring EastCrane(E&C) Reinforced Gearbox 11.1v Lipo Battery

Crazy, I only use SHS pistons. I have 3 SSG builds with 50k-150K shots on them, did not glue the rack. Building a DSG now, I have not glued the rack, at about 6k shots no problems yet.

thanks

Great video

Got a set of 16:1 and the only gear that was different then my stock 18:1 gears was the spur. It had 19 teeth up top not 20. Literally everything else was the same with the rest of the spur and the other two gears. When I did the math it came out to 17.82:1 for my so called 16:1 😑

Thank you so much for this 👊

Pls review or try the ICS Master mods

Love the classical music!

Any thoughts for upgrading a krytac kriss vector?

Love the editing and the music! Pls do more videos :3

What’s the 30k mean? I have always chosen my motor based on tpa and I don’t understand where the 30k comes from?