- 136
- 249 817
Bo White Racing
Приєднався 15 лис 2012
Drag racing and Turbo LS builds
Twin turbo LS S10 update. Truck is running and almost ready for the first test drive.
Twin turbo LS S10 on E85. Update video of the progress Iv made the last few weeks. We are about ready for the first test drive.
Переглядів: 1 291
Відео
Turbo LS S10 drag truck update. Engine running at the end of the video.
Переглядів 498Місяць тому
Turbo LS s10 update.
S10 update. Wiring a race truck.
Переглядів 2502 місяці тому
Here is an update on the S10. I been working on the wiring the last few weeks. Enjoying.
Turbo LS S10 update. Welding the waste gate to the turbos!!!!!!
Переглядів 1 тис.4 місяці тому
S10 update. Welding the hot side and welding the waste gate to the turbo exhaust housing.
Turbo LS S10 update and Meziere electric water pump.
Переглядів 9166 місяців тому
Update on the s10 and a look at the Meziere electric water pump part number WP119SHD.
Turbo LS drag truck. Turbo and intercooler placement.
Переглядів 1,1 тис.7 місяців тому
Working the the S10 today. Mocking up the turbo and intercooler.
Installing the wiring harness. Time to start cutting.
Переглядів 1,2 тис.7 місяців тому
Today I started to install the wiring harness. We will need to make some cuts.
New toys/equipment to help build the S10 drag truck.
Переглядів 3717 місяців тому
Got a new welder and a set of scales. Thank you for all the support.
S10 update fuel system complete.
Переглядів 1,9 тис.8 місяців тому
Update on the S10. Got the fuel system completely done.
Turbo LS S10 update. Building a wiring panel.
Переглядів 4439 місяців тому
Turbo LS S10 update. Building a wiring panel.
BTR valve covers and new valve springs installed!!!!
Переглядів 4949 місяців тому
BTR valve covers and new valve springs installed!!!!
S10 project update and new PTC powerglide!!!!!
Переглядів 85110 місяців тому
S10 project update and new PTC powerglide!!!!!
Test fitting the engine. Project update.
Переглядів 1,3 тис.10 місяців тому
Test fitting the engine. Project update.
Removing the wiring on the new project S10.
Переглядів 52711 місяців тому
Removing the wiring on the new project S10.
Ladder bar coil-over relocated | Turbo LS S10.
Переглядів 75411 місяців тому
Ladder bar coil-over relocated | Turbo LS S10.
Looking inside the spare engine to see what rods it has.
Переглядів 735Рік тому
Looking inside the spare engine to see what rods it has.
1992 Turbo LS S10 complete walk around of the combo.
Переглядів 5 тис.Рік тому
1992 Turbo LS S10 complete walk around of the combo.
S10 update squaring the rear end in the chassis.
Переглядів 308Рік тому
S10 update squaring the rear end in the chassis.
Turbo LS S10 update new circle D converter. 252mm pro series converter.
Переглядів 658Рік тому
Turbo LS S10 update new circle D converter. 252mm pro series converter.
truck is really looking good nice craftsmanship something to be proud of....
@@mikeday852 thanks Mike how your car doing?
What rad u using
@@YoungerPrice www.summitracing.com/parts/gri-2-58185-x Here the link.
@@BoWhiteRacing nice I'm running the summit one but don't seem to be cooling it enough
@@YoungerPrice mine got up to around 202 just at idle for 20 min. What pressure is your rad cap? I had a 16 psi but it would get hot so I went to a 24 psi. Also I’m thinking of doing a fan shroud they help a lot.
@@BoWhiteRacing mine is a 16 psi,I guess having a front mount isn't the best either also with these smaller rads were limited to fan selection,
Awesome! Can't wait! Your definitely ahead of me now. Mine has a little more involved though.
Looks good nice job and you sound young great work
Moi j aime bc ❤😅
Le ls super v8 que vous disait sans histoire à bon ❤😊
Such a clean setup can't wait to see it rolling
i wanna get you on DBW one day, its magic
I’m down to try it. Just never messed with it.
@@BoWhiteRacing the benefits are incredible with a little bit of learning, but you can do a much cleaner easier install imo and swap throttles in 1 minute, you can change the stop point and throttle curve, use it with the software for say, traction control or other control factors to close it, if you can crimp the tyco connectors and whatnot yourself, wich it looks like you are judging by the wiring and the dominator already, connectors from monkey fab are approx 40$ shipped and then i use 6/18 wire from amazon for the pedal and throttle run its in a black pvc thick shield so its oil and gas resistant, i have actually been crimping them for friends because the holley one is like 250 plus
@@BoWhiteRacing lmk if you wanna i could help you get your feet wet
@@BoWhiteRacing also sorry to write so much, a ton of the stock throttles are 84mm factory and basically free. so thats a positive. otherwise things like snake eater 92 and 102 work flawlessly
@@SloppyMechanics this is the first time Iv used a Holley dominator. The last 2 time I used the Holly terminator X. I’d like to play with it. Iv seen you do it and it seems like it runs well. And don’t worry about writing to much I enjoy the conversation.
i like the cut of your jib
Looking and sounding good Bo!
Damn got so much room for activities in the bed! Might as well put the rad in the rear haha. Any idea on the front rear weight bias?
@@buiItnotbought it’s 55% on the nose with no weight in the rear.
That's pretty good. I always wanted to build a square body s10 and put everything in the bed. One day
Yea I was going to put the rad in the back but I’m going to do some sticky track racing with it so don’t need as much weight in the back.
It’s my dream to build something like this and just take my old man for a cruise in it 😢 brings a tear to my eye thinking about it
What the actual fuck
Love seeing the progress. Keep up the great work Bo. Hope my build turns out half as nice.
Glad to see you back Bo! Good stuff brother!
Love these updates and what you do brother
@@SloppyMechanics thank you Matt. Just trying to make you hate S10’s less lol.
@@BoWhiteRacing like I always say it’s the owners lol 😂 you’re doing fine
@@SloppyMechanics oh trust me I know. I was in some S10 groups lol I get it. I thought it was funny and never had to worry about the sloppy tax.
🤌
Your attention to detail is awesome. Professional build done right out of your own garage. Great work my man.
@@jamesb5010 thank you I’m trying.
Heck yea, finally started mine last week after a year of working on it 🤘
@@KawiKlx143 hell yea buddy. Not much more to do.
Sounds nasty! Which cam did you go with?
@@BigMikesGarage I went with the sloppy best cam.
@@BoWhiteRacing Awesome! I've got the same cam in my 5.3 7875 el camino build. Hope to have it running soon
@@BigMikesGarage hell yea. Best of luck with it. I like the cam so far. The only other came Iv used is the SS2.
Me
What fuel pump did you use if you don’t mind asking
@@jgilyard4617 it’s a magna fuel 750 pro star.
Would you sell it?
Already have.
Do you happen to have a video of the fuel system setup?
@@chrisFamo yes I do. I’ll also try to cover it in the next video.
Amazing build 😍
Amazing to see the work you accomplish out the driveway with no lift or fancy tools. Keep up the good you're truly an inspiration to watch!
@@Rundown_Racecars trust me I wish I had a lift lol. Thank you I’m glad you like it.
Great job!!
Can't wait to see it rip.
Great job as always!
@@jamesb5010 thank you!!!
Looks great!
@@markeddington278 ready to get to the track.
Getting close!
@@BigMikesGarage it’s about to be done.
How do you install a bump and launch controller?
I’m using the Holley. If you have a Holly I have a video on my channel that shows how to wire and set it up.
what cage do you have in this truck?
@@helloyesh not sure I got the truck with the cage.
What circle D converter? What size
@@genzllabk23.8fastestinnwi8 252mm around 4500 rpm stall.
What stall you running in the power glide
10 Psi 2 Step Test
MAMALONA
What brand fuel line is that?
Red horse www.redhorseperformance.com/hoses/402-series-black-push-lock-hose/
😮😮😮
Good deal that’s awesome sounds great excited to see the progress.
Sounds awesome for a first start up. What cam did you go with this time?
It’s the sloppy best cam.
Cat said peace I’m out dawg
lol she was gone lol. 😂
Woot woot!
Awesome
congrats moving forward
Cat wasn't ready for the open headers
She wouldn’t come back outside lol.
Chevy for life! That S10 is sounding badass!
CHEVY 💪
What kind of shifter did you use?
Precision performance shifter.
getting close