Відео

Just stumbled upon your channel in the algorithm somehow. Liked and subscribed before I even watched this video, simply from the content and the fact that you are a fellow Aussie based RC enthusiast like myself. Gets repetitive listening to American/European RC Hobby channels 🙄

Merry Christmas!!! I peel the Traxass stickers off and feel much better.

What???

I’d knock that end plate off while it’s out and advance the timing a few degrees! No load on the motor set power supply at 4-5v tops! and advance till it’s screaming and done! Never do this with a higher power motor at full voltage if you like your fingers! Then install and run it on 3-4s and once it’s completely melted or exploded replace it with brushless lol! Nice break in btw!

Nice car. Thanks for showing. Looking forward for the run

Great job explaining how to install the servo saver screw, it can be something else to do.. As for the servo saver lock-nut, I set (all) mine the same way you did, brass tube flush with the opening. Great video and Merry Christmas, Happy Holidays & Happy New Year!!

The preciser you work and check, the less has to be adjusted later😉

Great job mate... As far as I remember, they always came with 4 bearings..

Locktite!!! She's going to blow!

Great video.... A few tips too, rotate those arms and a bit of grease on the threads, well done mate!!!!

Nice job mate... But I hope you won't need to buy a new kit... Loctite 242/243 is generally not considered safe for use on ABS plastic, as it is primarily designed for metal applications and can potentially damage or weaken the plastic due to stress cracking, especially when used on threaded connections with significant stress involved; always consult the product data sheet for specific compatibility information before applying it to plastic materials. This stuff has an oil/fluid that forms as it sets, that's the part that eats ABS plastic... Just a heads up and good luck.

👍🤙😎

Smart move with the steel pinions man!!!! I don't build a Clod without steel pinions, even with stock Clods. Adding a drop of oil on the motor bushings, another smart move, Plus that's a great tip for new comers.. Great Job!!!!!

Nice correction man... The steering isn't all that good on a stock Clod but there are things you can do to get more steering from it... On the knuckles (D1 & D2), you'll see "tabs" that hit the axle tubes/hub mounts, you could cut those tabs off and the knuckles will turn a bit more.. Also, cranking down on the servo saver nut more than what than manual states, just a bit more, the steering won't feel as "sloppy". Good luck with the gear boxes and keep an eye out for that pesky 3mm nut that goes into each gear box. Are you going Box Art or something different?

Hey mate, the top steering link on the servo should go to the front gearbox/servo saver. The way you installed it (as many others have, and a friend of mine did too), it will cause steering throw issues and/or binding. Just a heads up.. Look real good at the manual again..

Cruising along.

Great job so far mate... I just finished my Black Edition Super Clod Buster (still need to paint the body). I just say Clod, cause that's all they are, but with the added chassis braces ugly 4x4x4 grill and the dumb super charger ( I use the smaller air catcher instead), different colors & stickers. If you haven't seen or know of @MarkBryanRC & @robbrennanrc, go check them out as they built their first Clods about a year ago. Also, take a look at @TamiyaTalkRC if you haven't already.... He just built a tribute Clod from a Black Edition kit, looks killer.

Yupp, mine has locktide, too. Too many screws going into metal on this car

First , locktite ! Scary stuff if you get sloppy. Is that locktite 425?

Good to see you back, mate. Enjoy the build!

I put an aftermaret reinforcement plate under the steering servo during assembly on the advice of a friend. It was an excellent upgrade among the 100's available.

Very nice Mate.... Careful using that Loctite, It has a habit of eating Tamiya plastic... Ask anyone who's used it in the hobby... Get yourself some Tamiya AG Thread Lock #54032, it's an Anaerobic Gel.

The clod rabbit hole runs deep! MODS! MODS! MODS!!

And so it begins😉👍

Nice run at 43. Looked very stable

Congrats on the 43! That's a fantastic speed! The GPS issues still plaguing racers, I see. UGH! Hope to see you back in 2025!

Congrats on the 43

What pinion. Set up are you running?

Great run, mate. Way to represent the Aussies!!! We're doing our final run in a couple of days with the new 12x2 so hopefully we'll join you in the 40 club. 😅

Nicely done!

😎👍🤙

Great speed, congrats 👏

Awesome speed on the old Torque Tuned, buddy! The app is really annoying, I found that it helps to completely clear the phone for all kinds of other stuff, give it a chance to talk the damned little box, he he...

Great result👏

29 with a toque tuned is flying.

First!

Ready for a test run

Almost done.

I liked your magic trick👍🏻

Mate, so close to that Clod build. Congratulations! The channel is growing fast. Keep it up 😊

Nice paint on those wheel hex.

The body is killer on there. You should put some wide rear foams on there! Unless that’s against the rules

Awesome run man.

Hey mate, I see you're not on the latest scoreboard. I think you tagged CW-01 creations incorrectly. I think you need to type @cw-01creations46. Try to edit your description, mate. Good luck 😊

Welcome to the fun!

Excellent speed run you had there 👍 You whizzed past me by 1 mph as ive been stuck on 44 mph for the last month or so 😂 I will do the update video tomorrow (Monday) including this speed run time to get your channel up on the board 👍

Nice body choice! Looking to see future runs

Good first run, mate.

Great first pass, mate. The Hornet body was an excellent choice!

Haha horent for the win. Good stuff 👍🤙